Abstract:The motivation to design a more efficient and compact aircraft engine leads to a continuous increase in overall pressure ratio and decrease in the stage number in compressors. Compared to the traditional multi-stage compressor, a single-stage ultra-high-pressure-ratio centrifugal compressor with a pressure ratio higher than 10.0 can significantly improve the engine’s power-to-weight ratio and fuel economy with a reduced structure complexity. Thus, it has great potential to be adopted in the compression system of advanced aero engines, such as turboshaft engines, in the future. However, the highly narrow Stable Flow Range (SFR) of ultra-high-pressure-ratio centrifugal compressors is a severe restriction for engineering applications. This research focuses on the aerodynamic performance of a ultra-high-pressure-ratio centrifugal compressor, and three-dimensional simulation is employed to investigate the effect of Self-Recirculating Casing Treatment (SRCT) on the performance and stability of the centrifugal compressor. Firstly, the parametric model of SRCT is established to investigate the effect of geometry parameters (rear slot distance and rear slot width) on the aerodynamic performance of the centrifugal compressor. It is concluded that SRCT improves the compressor’s SFR but deteriorates its efficiency. Also, a non-linear and non-monotone relationship exists between the SFR and rear slot distance or width. Then, the flow mechanism behind the effect of SRCT is explored in detail. By introducing the SRCT, an additional flow path is provided across the blade along the circumferential direction, and the behavior of the shock wave and tip leakage flow is significantly changed, resulting in the obviously different loading distribution along the streamwise direction. As a result, the mixing and flow separation loss are enhanced in the impeller flow passage to deteriorate the efficiency. On the other hand, the blockage effect caused by the mixing of slot recirculation and mainstream flow near the impeller inlet increases the axial velocity and reduces the incidence angle below the 90% spanwise section, which is considered to effectively stabilize the impeller flow field and enhance the stability.

Effect of end wall boundary layer suction on the performance of high load helium compressor cascade

Effect of Tip Injection on Performance of Highly Loaded Helium Compressor in High-Temperature Gas-Cooled Reactor

Effect of Reynolds number on the aerodynamic performance of highly loaded helium compressor cascade in high temperature gas-cooled reactor

Effect of Leakage Flow on the Endwall Cooling Performance in High Subsonic Turbine Cascade

Similarity and Cascade Flow Characteristics of A Highly Loaded Helium Compressor

Influence of the Tip and Axial Clearances on the Aerodynamic Performance of a Helium Compressor

The Effect of End Wall Boundary Layer on Matching and Corresponding Flow Control Technique for Multistage Axial Compressor

Off-Design Performance Research of an Axial Helium Compressor for Htgr-10 Power Conversion Unit

Research on Effect of Endwall Contouring of Vaned Diffuser on Stable Operating Range of Centrifugal Compressor

Numerical Simulation of Effect of Blade End Slot on Performance of Compressor Cascade

Numerical investigation of boundary layer suction on certain highly loaded aspirated compressor at low speeds

An Investigation on Separation Configurations in Compressor Cascades with Boundary Layer Suction (BLS)

Experimental Study and Performance Analysis on High-Pressure Stage of Helium Compressor

The Endwall Effects of Stators with and Without Simplified Penny Gaps in a High-Loaded Multistage Compressor

Effect of Self-Recirculating Casing Treatment on the Aerodynamic Performance of Ultra-High-Pressure-Ratio Centrifugal Compressors

End-Wall Boundary Layers and Blockages of Multistage Axial Compressors under Different Conditions

Flow quality improvement of the wind tunnel testing for a highly-loaded compressor cascade at high incidence

Aerodynamic Design Method and Experimental Investigation of a High-Load Supersonic Compressor Cascade

Numerical Investigation of the Stator Hub Gap Effects on Aerodynamic Performance of a High-Pressure Compressor

Investigation of non-axisymmetric endwall contouring in a high loaded turbine stator cascade

Effect investigation of single-slotted and double-slotted configurations on the corner separation and aerodynamic performance in a high-load compressor cascade