Abstract:Longitudinal-torsional ultrasonic vibration-assisted milling is a machining method that can effectively improve the quality of the machined surface. When this method is used for the end milling of TC18 titanium alloy, however, the law of influence on the machined surface and subsurface remains unclear. In this study, we examined the effects of the ultrasonic amplitude, feed rate, and cutting speed on the machined surface morphology, roughness, surface residual stress, and subsurface microstructure in the longitudinal-torsional ultrasonic vibration-assisted end-milling process. According to the results, longitudinal-torsional ultrasonic vibration-assisted end milling can help form more obvious surface microtextures with a more distinct surface texture regularity at large amplitude, small feed rate, and high cutting speed. Compared with conventional milling, longitudinal-torsional ultrasonic vibration-assisted milling generates a larger roughness and surface residual stress and a deeper plastic deformation layer of the subsurface in the case of an obvious highly perturbed layer. In addition, the surface residual stress becomes greater and the plastic deformation layer gets deeper at a larger amplitude. When the amplitude was 5 μm, the surface residual stress was − 450.625 MPa and the depth of the deformation layer was 5.4 μm. The stress and depth increased by 21.55 % and 134.78 %, respectively, compared with those of conventional milling. The increase in the feed rate enhanced the roughness, decreased the surface residual stress, and did not significantly alter the depth of the plastic deformation layer. When the feed rate was 0.01 mm/z, the roughness was 0.383 μm and the surface residual stress was − 479.1 MPa. The feed rate and roughness increased by 42.63 % and 20.62 %, respectively, compared with those of conventional milling. With the increase in the cutting speed, the roughness increased, and the surface residual stress and the depth of the plastic deformation layer decreased. When the cutting speed was 15 m/min, the roughness was 0.31 μm, the surface residual stress value was − 454.7 MPa, and the depth of the plastic deformation layer was 5.7 μm. These three parameters increased by 17.8 %, 18.79 %, and 92.5 %, respectively, compared with those of conventional milling. This research has certain application prospect in surface machining of titanium alloy and quality control of machined surface.

Surface Residual Stress of Gamma Titanium Aluminide in Milling Process

Numerical simulation on surface residual stress for titanium alloy

Study on Residual Stress Produced in Milling of Aeronautic Structure

Simulation and Study on Surface Residual Stress Influence of TC4 Titanium Alloy

Surface and subsurface analysis of TC18 titanium alloy subject to longitudinal-torsional ultrasonic vibration-assisted end milling

Finite Element Analysis of the Milling of Ti6Al4V Titanium Alloy Laser Additive Manufacturing Parts

Theoretical investigation of machining-induced residual stresses in longitudinal torsional ultrasonic–assisted milling

Simulation Study on Residual Stress Distribution of Machined Surface Layer in Two-Step Cutting of Titanium Alloy

Investigation of the influence of initial residual stress and toolpaths on milling deformation of titanium alloy

Residual stress prediction in axial ultrasonic vibration–assisted milling in situ TiB2/7050Al MMCs

Catastrophe Models for Cognitive Workload and Fatigue in a Vigilance Dual Task

Experimental study on surface residual stress of titanium alloy curved thin-walled parts by ultrasonic longitudinal-torsional composite milling

Modeling and optimization of surface residual stress profiles in milling of aluminum 7075-T6 alloy

Analytical modeling of milling residual stress under different tool wear conditions

Construction of a predictive model for residual stresses in micro-milling of 7075 aluminum alloy

Finite element simulation of residual stress in machining of Ti-6Al-4V with a microstructural consideration

Residual compressive stress prediction determined by cutting-edge radius and feed rate during milling of thin-walled parts

Prediction and experimental research of abrasive belt grinding residual stress for titanium alloy based on analytical method

Research on cutting force and surface integrity of TC18 titanium alloy by longitudinal ultrasonic vibration assisted milling

Modelling and Optimization of Machining of Ti-6Al-4V Titanium Alloy Using Machine Learning and Design of Experiments Methods

Study of surface integrity of milled gamma titanium aluminide