Abstract:Longitudinal-torsional ultrasonic vibration-assisted milling is a machining method that can effectively improve the quality of the machined surface. When this method is used for the end milling of TC18 titanium alloy, however, the law of influence on the machined surface and subsurface remains unclear. In this study, we examined the effects of the ultrasonic amplitude, feed rate, and cutting speed on the machined surface morphology, roughness, surface residual stress, and subsurface microstructure in the longitudinal-torsional ultrasonic vibration-assisted end-milling process. According to the results, longitudinal-torsional ultrasonic vibration-assisted end milling can help form more obvious surface microtextures with a more distinct surface texture regularity at large amplitude, small feed rate, and high cutting speed. Compared with conventional milling, longitudinal-torsional ultrasonic vibration-assisted milling generates a larger roughness and surface residual stress and a deeper plastic deformation layer of the subsurface in the case of an obvious highly perturbed layer. In addition, the surface residual stress becomes greater and the plastic deformation layer gets deeper at a larger amplitude. When the amplitude was 5 μm, the surface residual stress was − 450.625 MPa and the depth of the deformation layer was 5.4 μm. The stress and depth increased by 21.55 % and 134.78 %, respectively, compared with those of conventional milling. The increase in the feed rate enhanced the roughness, decreased the surface residual stress, and did not significantly alter the depth of the plastic deformation layer. When the feed rate was 0.01 mm/z, the roughness was 0.383 μm and the surface residual stress was − 479.1 MPa. The feed rate and roughness increased by 42.63 % and 20.62 %, respectively, compared with those of conventional milling. With the increase in the cutting speed, the roughness increased, and the surface residual stress and the depth of the plastic deformation layer decreased. When the cutting speed was 15 m/min, the roughness was 0.31 μm, the surface residual stress value was − 454.7 MPa, and the depth of the plastic deformation layer was 5.7 μm. These three parameters increased by 17.8 %, 18.79 %, and 92.5 %, respectively, compared with those of conventional milling. This research has certain application prospect in surface machining of titanium alloy and quality control of machined surface.

Residual stress prediction in axial ultrasonic vibration–assisted milling in situ TiB2/7050Al MMCs

Theoretical investigation of machining-induced residual stresses in longitudinal torsional ultrasonic–assisted milling

Residual stress prediction in ultrasonic vibration–assisted milling

Numerical simulation on surface residual stress for titanium alloy

Residual compressive stress prediction determined by cutting-edge radius and feed rate during milling of thin-walled parts

Residual stresses in ultrasonic vibration assistance turning cemented carbide

Finite element simulation of residual stress in machining of Ti-6Al-4V with a microstructural consideration

Analytical modeling of milling residual stress under different tool wear conditions

Investigation of Cutting Force in Longitudinal-Torsional Ultrasonic-Assisted Milling of Ti-6Al-4V

Effect of thermo-mechanical loading on machining induced residual stresses in ultrasonic vibration assisted turning of Ti6Al4V alloy

Milling mechanism and surface roughness prediction model in ultrasonic vibration-assisted side milling of Ti–6Al–4 V

Construction of a predictive model for residual stresses in micro-milling of 7075 aluminum alloy

Experimental Investigation on Axial Ultrasonic Vibration Assisted Milling of Cr12MoV

Investigation on cutting forces in ultrasonic vibration assisted milling of particle-reinforced titanium matrix composites (PTMCs)

Calculation of residual stress in ultrasonic vibration assisted grinding considering thermal-mechanical coupling: a numerical-analytical hybrid prediction approach

Modeling of cutting forces in 1-D and 2-D ultrasonic vibration-assisted milling of Ti-6Al-4V

Research on cutting force and surface integrity of TC18 titanium alloy by longitudinal ultrasonic vibration assisted milling

Surface and subsurface analysis of TC18 titanium alloy subject to longitudinal-torsional ultrasonic vibration-assisted end milling

The Role of Material Model in the Finite Element Simulation of High-Speed Machining of Ti6Al4V

Force prediction in ultrasonic vibration-assisted milling

Experimental study on surface residual stress of titanium alloy curved thin-walled parts by ultrasonic longitudinal-torsional composite milling