Abstract:In order to investigate the effect of grain boundaries on the mechanical response in the micrometer and submicrometer levels, complementary experiments and molecular dynamics simulations were conducted on a model bcc metal, tantalum. Microscale pillar experiments (diameters of 1 and 2 μm) with a grain size of ~100–200 nm revealed a mechanical response characterized by a yield stress of ~1500 MPa. The hardening of the structure is reflected in the increase in the flow stress to 1700 MPa at a strain of ~0.35. Molecular dynamics simulations were conducted for nanocrystalline tantalum with grain sizes in the range of 20–50 nm and pillar diameters in the same range. The yield stress was approximately 6000 MPa for all specimens and the maximum of the stress–strain curves occurred at a strain of 0.07. Beyond that strain, the material softened because of its inability to store dislocations. The experimental results did not show a significant size dependence of yield stress on pillar diameter (equal to 1 and 2 um), which is attributed to the high ratio between pillar diameter and grain size (~10–20). This behavior is quite different from that in monocrystalline specimens where dislocation ‘starvation’ leads to a significant size dependence of strength. The ultrafine grains exhibit clear ‘pancaking’ upon being plastically deformed, with an increase in dislocation density. The plastic deformation is much more localized for the single crystals than for the nanocrystalline specimens, an observation made in both modeling and experiments. In the molecular dynamics simulations, the ratio of pillar diameter (20–50 nm) to grain size was in the range 0.2–2, and a much greater dependence of yield stress to pillar diameter was observed. A critical result from this work is the demonstration that the important parameter in establishing the overall deformation is the ratio between the grain size and pillar diameter; it governs the deformation mode, as well as surface sources and sinks, which are only important when the grain size is of the same order as the pillar diameter.

Microstructure and Strength of a Tantalum-Tungsten Alloy after Cold Rolling from Small to Large Strains

Microstructural Evolution of Ta-4%W During Cold Rolling

The Microstructure and Strength of a Tantalum Alloy: Influence of Temperature

The characteristics of forged tantalum and dynamic constitutive modelling

Effects of Tantalum Concentration on the Microstructures and Mechanical Properties of Tungsten-Tantalum Alloys

Molecular Dynamics Simulation of Nanocrystalline Tantalum under Uniaxial Tension

Properties and Structure of Ta and Ta-W Alloys During Cold-Roiling Process

Evolution of Deformation Microstructures of Cold-Rolled Ta-2.5w Alloy with Coarse Grains at Low to Medium Strains

Effect of the Severe Plastic Deformation on the Corrosion Resistance of a Tantalum–Tungsten Alloy

The evolution of cold-rolled deformation microstructure of {0 0 1}〈1 1 0〉 grains in Ta-7.5 wt%W alloy foils

The Evolution of Dislocation Microstructure in Electron Beam Melted Ta-2.5W Alloy During Cold Rolling

High Strain Monotonic Deformation-Structure And Strength

Evolution of Texture and Deformation Microstructure in Ta–2.5W Alloy During Cold Rolling

Micro-Mechanical Response of Ultrafine Grain and Nanocrystalline Tantalum

Control of Microstructure and Properties for Tantalum-Tungsten Alloy Component Manufacturing in Cold Forging and Subsequent Annealing Process

The Evolution of Cold-Rolled Deformation Microstructure of {001}〈110〉 Grains in Ta–7.5wt%W Alloy Foils

Effect of Cold Rolling on Microstructure and Properties of a Novel Ni-W-Co-Ta Heavy Alloy

Strain Path Dependence of Microstructure and Annealing Behavior in High Purity Tantalum

Texture Evolution, Microstructure, and Superelastic Properties of Different Cold-Rolled Ti-Zr-Nb-Sn Strain Glass Alloys

The evolution of shear bands in Ta-2.5W alloy during cold rolling

Microstructures and Deformation Mechanisms of Cr26Mn20Fe20Co20Ni14 Alloys