Abstract:The threat of cascading damage to downstream components caused by the light modulation intensification of laser repaired morphology on the surface of fused silica optics cannot be ignored in high-power laser systems. This paper uses the angular spectrum diffraction theory based on the analysis of repaired surface morphology of CO 2 laser rapid ablation mitigation to study the influence of different repaired morphologies on the downstream 355 nm laser transmission. Studies show that the arc-shaped laser processing lines on the repaired surface are formed by the residual height superposition of the material after laser scanning of two adjacent layers, and the short-pulse laser can substantially suppress the heat-affected zone of the repaired area. The offaxis ring caustic and on-axis hotspot are sequentially generated in the downstream modulated light fields of the conical repaired sites with different diameters. A secondary peak with modulation larger than 3 emerges downstream of the modulation curve.Meanwhile, the maximum modulation and the secondary peak increase with the diameter and cone angle of the repaired site, and the position of the secondary peak appears farther away from the rear surface. The modulations of three repaired sites with cone angles of 15°, 20°, and 25° can finally be stabilized below 3. Overall, the downstream optics should be installed far away from the positions where the maximum modulation and the secondary peak emerge. Additionally, the maximum value and the secondary peak of the downstream light modulation of double repaired sites are larger than that of the single repaired site, and both rise as the repaired sizes increase. Thus, large-scale and large-size repairing of multiple surface damages in the same area should be avoided in the laser repairing of fused silica.

Combined Studies of Surface Evolution and Crack Healing for the Suppression of Negative Factors During CO2 Laser Repairing of Fused Silica

Experimental and Theoretical Investigation of Localized CO2 Laser Interaction with Fused Silica During the Process of Surface Damage Mitigation

Morphology evolution mechanisms and localized structural modification of repaired sites on fused silica optics processed by CO2 laser rapid ablation mitigation

Formation Mechanism of Bubbles in the Crack Healing Process of Fused Silica Using a CO2 Laser

INTEGRATED TECHNOLOGY FOR DETECTION AND REPAIR OF MECHANICAL COMPONENT SURFACE FATIGUE MICROCRACKS USING PULSED LASER

Investigation on the influence of the CO2 laser parameters on the defect healing process of fused silica

Material migration and damage characteristics of fused silica optical surface treated by CO 2 laser/short – pulse ultraviolet laser

Experimental investigation and numerical simulation of defect elimination by CO2 laser raster scanning on fused silica

Formation Mechanism of Surface Morphology in the Process of CO2 Pulsed Laser Processing of Fused Silica Optics

Theoretical and Experimental Investigations of Localized CO2 Laser-Fused Silica Interactions and Thermo-Mechanical Properties of Mitigated Sites

Research on Laser-Induced Damage Post-Restoration Morphology of Fused Silica and Optimization of Patterned CO2 Laser Repair Strategy

Coupled Thermal-Mechanical Analysis of CO<sub>2</sub> Laser Irradiation on Fused Silica

Evolution of Point Defects in Mechanical Cracks of Fused Silica after CO2 Laser Melting

Research Development of CO2 Laser Treatment for Repair Damage in Fused Silica

Incident Laser Modulation of a Repaired Damage Site with a Rim in Fused Silica Rear Subsurface

Repaired Morphology of CO 2 Laser Rapid Ablation Mitigation of Fused Silica and Its Influence on Downstream Light Modulation

Repaired Morphology Induced Optical Modulation in Fused Silica Based on Scalar Diffraction Theory

Modeling of Surface Damage Mitigation in Fused Silica with Carbon Dioxide Laser

Optical Modulation of Repaired Damage Site on Fused Silica Produced by CO2 Laser Rapid Ablation Mitigation

Physical Mechanism of Pulsed Laser Interaction with Fused Silica Optics During CO2 Laser Mitigation Process

Theoretical and experimental investigations in thermo-mechanical properties of fused silica with pulsed CO2 laser ablation