Abstract:Objective Depositing nano-gold films on the pure titanium substrate by ionic self-assembled mutilayers technique (ISAM) and sintering a special titanium porcelain powder, the study was aim to investigate the effect of the deposited nanogold composite films on the adhesion of porcelain to titanium. Methods Twenty pure titanium specimens were prepared according to ISO 9693 requirement. Grouped according to whether or not depositing composite nano-gold film, nano-gold film deposited pure titanium specimens as the experimental group (AuS);non-nanogold gold film deposited specimens as the control group (S), each group has 10 standard specimens. Field emission scanning electron microscope(FE-SEM) was used to observe the surface morphology of titanium specimen after depositing composite nano-gold films, and further observe the microstructure of the interface between titanium and porcelain after sintered. The titanium-porcelain bonding strength was assessed by three point bending method and statistical analysis. The titanium-porcelain fracture mode of the specimens was determined by Stereoscopic microscope. The distribution of the Au element on the interface of titanium-porcelain was detected by electron microprobe (EMP). Results The titanium-porcelain bonding strength of nano-gold film deposited group was significantly higher than those of the undeposited group[(36.24±3.64) MPa and (30.78± 3.83) MPa, P<0.05 ]. FE-SEM illustrated that the surface of the nano-gold deposited group formed a uniform, dense composite nano-gold film. Stereomicroscope and SEM images showed that the titanium-porcerlain interface of AuS group was continuous and closely, the fracture mode was given priority to mixed mode fracture;while the interface of S group had an obviously crack and occasional bubble, the fracture mode was given priority to interfa-cial fracture. Small, white spots of gold particles could be detected along the titanium-porcelain bonding interface by electron microprobe (EMP). Conclusions Under the conditions of the present study, composite nano-gold films deposited on the pure titanium surface can significantly improve the bonding strength between the Super porcelain Ti-22 special titanium porcelain powder and the preformed titanium specimens.

The Influence of Glass Particle Size on the Interfacial Bonding Strength of Au/ceramic Co-Fired Structure

Improvement of Gold Electrode Conductivity after Cofiring with CaO–B2O3–SiO2 Green Tapes for LTCC Application

Effects of Glass on Densification and Interfacial Bonding of LTCC Co-Fired Ag Electrode

Effects of viscosity and wettability of Pb-B-Si-O glass in silver paste on the co-firing densification of LTCC

Decrease in the camber degree of Au/ceramic co-fired structure for LTCC technology

Effects of Pb–B–Si–O Glass on the Microstructures and Electrical Properties of Silver Electrode for LTCC Application

The Au Electrode Optimized by the Wettability and Viscosity of Glass for LTCC Techonolgy

Effect of sputtering gold coating on the bonding strength between pure titanium and two low-fusing porcelains

[Effect of Sintering Gold Paste Coating on the Bonding Strength of Pure Titanium and Three Low-Fusing Porcelains].

Nanoscaled Interface Between Microgold Particles and Biphase Glass‐Ceramic Matrix

A basic study on improving dental titanium-ceramic bonding by Au nanoparticle film deposition technique

The influence of Bi2O3 glass powder in silver paste on the fabrication of ohmic contacts and its potential effectiveness in solar cells and integrated circuits on p-type silicon substrates

Particle size modulation for effectively optimizing the dielectric and mechanical properties of La2O3–B2O3 based glass-ceramic/ceramic LTCC substrates

Thermal Sintering Matchability Between Low‐Temperature Cofired Ceramic Substrate and Silver Pastes and the Effect of CuO on Silver Diffusion Inhibition

Thermal Sintering Matchability between LTCC Substrate and Silver Pastes and the Effect of CuO on Silver Diffusion Inhibition

Effect of properties and crystallization behavior of BaO‐ZnO‐B 2 O 3 ‐SiO 2 glass on the electrical conductivity of Cu paste

Effect of gold sputter coating time on the bond strength of titanium alloy and porcelain

Fabrication and Characterization of Nickel-Gold Plateble LTCC Substrates Based on Borosilicate Glass/al2o3 System

Effect of Particle Size on the Sintering Behavior, Microstructure and Flexural Strength of Lithium Disilicate Glass-Ceramics

Formation of a Highly Conductive Thick Film by Low-Temperature Sintering of Silver Paste Containing a Bi2O3-B2O3-ZnO Glass Frit

Enhancement of the Bonding Strength of Al2O3 Ceramics Using a Reactive Intermediate Layer Formed by Aerosol Deposition