Abstract:Application of high-voltage spinel LiNi0.5Mn1.5O4 cathode material is the closest and the most realistic approach to meeting the midterm goal of lithium-ion batteries for electric vehicles (EVs) and plug-in hybrid electric vehicles (HEVs). However, this application has been hampered by long-standing issues, such as capacity degradation and poor first-cycle Coulombic efficiency of LiNi0.5Mn1.5O4 cathode material. Although it is well-known that the structure of LiNi0.5Mn1.5O4 into which Li ions are reversibly intercalated plays a critical role in the above issues, performance degradation related to structural changes, particularly in the first cycle, are not fully understood. Here, we report detailed investigations of local atomic-level and average structure of LiNi0.5Mn1.5O4 during first cycle (3.5-4.9 V) at room temperature. We observed two types of local atomic-level migration of transition metals (TM) ions in the cathode of a well-prepared LiNi0.5Mn1.5O4//Li half-cell during first charge via an aberration-corrected scanning transmission electron microscopy (STEM). Surface regions (similar to 2 nm) of the cycled LiNi0.5Mn1.5O4 particles show migration of TM ions into tetrahedral Li sites to form a Mn3O4-like structure. However, subsurface regions of the cycled particles exhibit migration of TM ions into empty octahedral sites to form a rocksalt-like structure. The migration of these TM ions are closely related to dissolution of Ni/Mn ions and building-up of charge transfer impedance, which contribute significantly to the capacity degradation and the poor first-cycle Coulombic efficiency of spinel LiNi0.5Mn1.5O4 cathode material. Accordingly, we provide suggestions of effective stabilization of LiNi0.5Mn1.5O4 structure to obtain better electrochemical performance.

Monitoring Structural Changes during Electrochemical Cycling of Solid-Solution Spinel Oxide MgCrVO 4

LiNi0.5Mn1.5O4 cathode microstructure for all-solid-state batteries

Structure Change of Orthorhombic LiMnO2cathodes During Electrochemical Cycle for Rechargeable Lithium Battery

Unravelling the Impact of Reaction Paths on Mechanical Degradation of Intercalation Cathodes for Lithium-Ion Batteries.

Ultraporous, Ultrasmall MgMn2O4 Spinel Cathode for a Room-Temperature Magnesium Rechargeable Battery

Boosting the Electrochemical Performance of a Spinel Cathode with the In Situ Transformed Allogenic Li-Rich Layered Phase

Oxide spinels with superior Mg conductivity

Mg(Al, Fe, Mn, REE)2O4 Spinel Prepared from Pelagic REE-Rich Clays and Application as Magnesium-Ion-Battery Cathodes

Surface Magnesium Substitution at Spinel Lithium Manganate 8a Tetrahedral Sites for Suppressed Manganese Dissolution and Enhanced Cycle Stability

Unconventional irreversible structural changes in a high-voltage Li–Mn-rich oxide for lithium-ion battery cathodes

Insight into the cation migration and surface structural evolution of spinel LiNi0.5Mn1.5O4 cathode material for lithium-ion batteries

Phase Transition Mechanism of ZnMn 2 O 4 Spinel Oxide with Electrochemical Magnesium-Ion Insertion

Tracking the Structural Evolution at Atomic-Scale in the Spinel Mn3o4 Induced by Electrochemical Cycling

Study on Electrochemical Behavior of the Positive Electrode Mg1.2mn1.8o4 in Magnesium Ion Battery

Fine nanostructure design of metal chalcogenide conversion-based cathode materials for rechargeable magnesium batteries

Research Development on Spinel Lithium Manganese Oxides Cathode Materials for Lithium-Ion Batteries

Electrochemical Behavior And Surface Structural Change Of Limn2o4 Charged To 5.1 V

Solid-State Electrolytes for Rechargeable Magnesium-Ion Batteries: From Structure to Mechanism

In‐Situ Lattice Tunnel Intercalation of Vanadium Pentoxide for Improving Long‐Term Performance of Rechargeable Magnesium Batteries

Insight into the Atomic Structure of High-Voltage Spinel Linio3mn1.5o4 Cathode Material in the First Cycle

Crystallographic‐Site‐Specific Structural Engineering Enables Extraordinary Electrochemical Performance of High‐Voltage LiNi 0.5 Mn 1.5 O 4 Spinel Cathodes for Lithium‐Ion Batteries