Abstract:This work presents a 14-bit 500 MS/s single-channel pipelined-successive-approximation-register (SAR) analog-to-digital converter (ADC) with an adaptively biased floating inverter amplifier (AB-FIA) as the residue amplifier (RA) and a hybrid reference ripple mitigation (H-RRM) technique to relax the power and area burden on the reference stabilization. Leveraging the adaptively biased architecture in the last stage FIA, the speed and open-loop gain of the proposed two-stage FIA are enhanced compared with the conventional cascode counterpart. Besides, the impact of the reference error on the pipelined-SAR conversion accuracy is alleviated by hybridizing the improved reference ripple cancellation (RRC), reference ripple neutralization (RRN), and reference buffer (RBUF). The improved RRC removes the potential noise coupled from the floating capacitor to counter the decision error during the sub-SAR conversion in the first stage. Meanwhile, the RRN facilitates a rapid reference recovery. These acts constitute the H-RRM, which assists a high-speed and high-resolution pipelined-SAR process with a relaxed integrated reference RBUF with low-power and compact area. The prototype ADC was fabricated in a 28 nm CMOS process; it consumes 6.34 mW total power at 500 MS/s, including 2.4 mW dynamic power of RBUF. It occupies an active area of 0.018 mm $^{2}$ , which the ADC core area of 0.0168 mm $^{2}$ and the area of RBUF with a 2.3 pF decoupling capacitor is 0.00105 mm $^{2}$ . The measured signal to noise and distortion ratio (SNDR) and spurious free dynamic range (SFDR) are 64.2 dB and 80.55 dB with a Nyquist input, respectively, leading to a 170.2 dB Schreier figure-of-merit (FoM) (FoM $_{\mathrm{S}}$ ) and 9.6 fJ/conversion-step Walden FoM (FoM $_{\mathrm{W}}$ ).

A Low Power Residue Amplifier using Incomplete Settled Differential Flipped Voltage Follower

The Design of a Low-Voltage Rail-to-Rail CMOS Operational Amplifier

A Parasitic Elimination Bootstrapped Switch and a Fast Settling Residual Amplifier for High-Speed and High-Resolution Pipelined ADC

A 1.5 Mw 68 Db SNDR 80 Ms/s 2<formula Formulatype="inline"> <tex Notation="TeX">$\times$</tex></formula> Interleaved Pipelined SAR ADC in 28 Nm CMOS

A Residue Amplifier with 85 Db DC Gain and 15 GHz Closed-Loop Bandwidth for 14-Bit 3GSPS Pipeline ADC.

A Low-Power, High-Speed Open-Loop Residue Amplifier for Pipelined ADCs with Digital Calibration

9.4 A 182.3dB FoM<inf>s</inf> 50MS/s Pipelined-SAR ADC using Cascode Capacitively Degenerated Dynamic Amplifier and MSB Pre-Conversion Technique

A Floating-Ring Hybrid Amplifier Insensitive to PVT and Common-mode Variation Without CMFB for High-Speed ADCs

A Direct Feedback FVF LDO for High Precision FMCW Radar Sensors in 65-nm CMOS Technology

A Low Noise High PSR LDO Based on N-type Flipped Voltage Follower

A 14b 500 MS/s Single-Channel Pipelined-SAR ADC With Reference Ripple Mitigation Techniques and Adaptively Biased Floating Inverter Amplifier

A Pipelined SAR ADC Reusing the Comparator As Residue Amplifier

A 10b 1.25GS/s Residue Post-Amplified Pipelined-SAR ADC with Supply-and-Temperature Stabilized Open-Loop Residue Amplifier.

Design of A Reference Buffer with Ultralow Output Resistance for High-speed ADCs

A 13-Bit 312.5-Ms/s Pipelined SAR ADC with Open-Loop Integrator-Based Residue Amplifier and Gain-Stabilized Integration Time Generation

A Wide-Range 12b 150ms/s P-SAR ADC with Open-Loop Residue Amplifier for Ultrasound AFE.

An 871nw 96.2Db-Sndr Pipelined NS SAR ADC Achieving 180.8Db-Fomsndr with a Charge-Efficient CLS-Assisted Two-Stage FIA

A 13-Bit 312.5-Ms/s Pipelined SAR ADC with Integrator-type Residue Amplifier and Inter-stage Gain Stabilization Technique

9.1 A 2mW 70.7dB SNDR 200MS/s Pipelined-SAR ADC with Continuous-Time SAR-Assisted Detect-and-Skip and Open-then-Close Correlated Level Shifting.

An 871 Nw 96.2 Db SNDR Pipelined Second-Order Noise-Shaping SAR ADC Employing Charge-Efficient CLS-Assisted Residue Amplifier

A High Performance Low Power 12-Bit 40ms/s Pipelined ADC