Abstract:The stacking sequences of fiber-reinforced composites for optimization of turbine blades with the best performance have become a focus of attention. However, the optimization and design principles of its flexural performance are not yet mature. Referring to the problems in previous work, a 3D finite element flexural model of carbon fiber reinforced composites was established based on the Abaqus/Explicit VUMAT subroutine through the Tsai-Wu failure criterion. The influencing laws and optimization mechanisms of different stacking patterns (e.g., different orientations, number of orientation plies, combination of multiple orientation plies, and symmetry/asymmetry structures) on the flexural properties of the composites were systematically investigated, and corresponding design references for the optimization of stacking patterns were given. The results show that the smaller the value of ∣θ−45°∣ (θ represents the angle of the orientation ply), the more obvious the stress reduction of the orientation ply, and the orientation ply located in the outer layer is more conducive to the improvement of flexural performance. As the number of orientation plies increases, the flexural strength and displacement increase, but the stability decreases, in which the laminate with 50 % 0° orientation plies has the best overall performance. In addition, the stability ranking of the laminate stacking sequences for the same 0° orientation ply proportion is: multi-orientation asymmetric > multi-orientation symmetric > single-orientation symmetric. In particular, the [75/02/60/30/02/15] laminate has the best overall performance with the flexural strength of 974 MPa and the Y-axis offset of 0.057 mm, and its stability is 66 % higher than that of the [15/02/75]S laminate. Under the same tensile/compressive stresses, the actual stress of the warp/weft in the orientation ply is less than the maximum ideal stress and the stress of Y-axis direction SY ≠ 0, which delays the fracture of the orientation ply and causes displacement offset, and the increase of the number of orientation plies will aggravate this effect. The obtained highlighted results can provide valuable references for the design and optimization of stacking patterns of plain fabric-reinforced laminates with high flexural properties.

Identifying Optimal Rotating Pitch Angles in Composites with Bouligand Structure

Cross-helicoidal Approach to the Design of Damage-Resistant Composites

Optimization Design and Nonlinear Bending of Bio-Inspired Helicoidal Composite Laminated Plates

Fiber‐reinforced sustainable biomimetic Bouligand structures for hot and humid environments

Increasing the Compressive Strength of Helicoidal Laminates after Low-Velocity Impact upon Mixing with 0° Orientation Plies and Its Analysis

Three-dimensional crack bridging model of biological materials with twisted Bouligand structures

Nested helicoids in biological microstructures

Discontinuous fibrous Bouligand architecture enabling formidable fracture resistance with crack orientation insensitivity

Collaborative optimization for variable stiffness composite laminates using a fiber angle description method based on Archimedean spiral function

Manipulating impact damage modes in composite laminates by helical pitch angle and ply thickness

First-Ply Failure Analysis of Helicoidal/Bouligand Bio-Inspired Laminated Composite Plates

Understanding the helicoidal damage behavior of bio-inspired laminates by conducting multiscale concurrent simulation and experimental analysis

Crack modes and toughening mechanism of a bioinspired helicoidal recursive composite with nonlinear recursive rotation angle-based layups

Investigation on the Influence of Fiber Bundle Undulating Architecture on Tensile Behavior of Filament Wound Composite Laminates

Bending and Vibration of a Bio-Inspired Bouligand Composite Plate Using the Finite-Element Method

An insight into the buckling behavior of double- and cross-helicoidal laminated composite plates inspired by dactyl's club

An analytical study on low velocity impact resistance behaviors of general bio‐inspired helicoidal composite plates

A multiscale fracture model to reveal the toughening mechanism in bioinspired Bouligand structures

Numerical Investigation on the Design and Optimization of Stacking Pattern for High Flexural Performance Carbon Fiber Reinforced Resin Matrix Composites

Manufacturing of bioinspired Bouligand structures using ultrasound assisted 3D printing

Analysis of Pseudo-Ductility in Thin-Ply Carbon Fiber Angle-Ply Laminates