Evaluation of sand liquefaction under the GIS environment

张凌,施斌,王宝军

DOI: https://doi.org/10.16030/j.cnki.issn.1000-3665.2000.05.005

2000-01-01

Abstract:A method for analyzing the liquefaction potential index under GIS environment is introduced, and the analysis process and the interface with GIS are deciphered in details

What problem does this paper attempt to address?

Characterizing the Liquefaction Potential and Pore Pressure Generation of Silty Sands Through the Energy-Based Approach in the Framework of Critical State Soil Mechanics

Xiao Wei,Jun Yang,Zhong-Xuan Yang

DOI: https://doi.org/10.1061/jggefk.gteng-11910

IF: 3.9

2024-01-01

Journal of Geotechnical and Geoenvironmental Engineering

Abstract:Evaluation of the liquefaction susceptibility of soils is one of the most important subjects in geotechnical earthquake engineering. The energy-based liquefaction evaluation procedure, with a focus on seismic energy propagation and dissipation in soils, has attracted increasing attention in recent years. This paper presents a systematic analysis of cyclic triaxial test data of three series of silty sands through the energy-based approach. The stress-normalized accumulative dissipated strain energy per unit volume required for triggering liquefaction is used to evaluate the liquefaction potential of sands. It is a function of void ratio, fines content, and sand type. The pore pressure generation with the stress-normalized accumulative dissipated energy per unit volume can be simulated by a one-parameter pore pressure model, and the model parameter is affected by void ratio, fines content, and sand type. Unified characterizations of the stress-normalized accumulative dissipated energy per unit volume required for liquefaction and the fitting parameter of the pore pressure model are proposed in the framework of critical state soil mechanics.
Analysis for Influence of Multi-Layered Soil Stratum on Sand Liquefaction

庄迎春,谢康和,朱益军,徐洋

DOI: https://doi.org/10.3969/j.issn.1000-7598.2003.06.026

2003-01-01

Abstract:A new analytical solution which is about shearing stress of sand layer with underlying substratum and upper covering layer under the suppose of known earthquake intensity or layer displacement, is obtained by Laplace transformation; and a new differentiation method for sand liquefaction is proposed. Additionally, the influence of the soil parameters on sand liquefaction is analyzed by computer programming; from which the possibility of sand liquefaction can be judged under different combination conditions. It is of benefit to practical engineering judgement.
Liquefaction Analysis By Gis Method

Bj Wang,B Shi,L Zhang

DOI: https://doi.org/10.1201/9780203739501-19

2001-01-01

Abstract:On the basis of reviews on current practices of evaluating liquefaction, a probabilistic method with the purpose which can interface with Geographical Information System (GIS) better is introduced, the liquefaction analysis process in GIS environment is established, and the interface with GIS are presented in details.
Spatial distribution simulation method for liquefaction index probability

SHI Cheng-wei,FENG Qi-min,JIA Jing

DOI: https://doi.org/10.3969/j.issn.1009-6825.2008.29.070

2008-01-01

Abstract:This paper depicts the probability meaning of sand liquefaction index based on the Code for Seismic Design of Buildings,studies the liquefaction index probability method of analyzing liquefaction possibility index under GIS environment,particularly expatiates the analysis process and GIS application method.Through an engineering example,the spatial distribution simulation analysis process for Zibo city centre liquefaction index probability is expatiated.
Risk-evaluating System of Seismic Site Liquefaction Based on GIS Technique:A Primary Research

汤皓,陈国兴,邵进达

DOI: https://doi.org/10.3969/j.issn.1004-4574.2004.05.021

2004-01-01

Abstract:This paper uses GIS technology and MapInfo to synthetically analyse the potential risk of sandy soil liquefaction of the ground in Huai′an City and the database systems of sandy soil liquefaction also has been built up. Regard the database as the background, the evaluation system for potential sandy soil liquefaction was established that the hazard of sandy soil liquefaction of the ground can be analyzed and evaluated. The research shows that introduction of GIS technique into the evaluation of potential risk of earthquake-induced sandy soil liquefaction of the ground not only can convenience the input,management,inquiry and analysis of the data, make the results directly displayed in the forms of maps, convenience the fast effective judgements of decision making body.
Probabilistic Estimation of Seismic Liquefaction Potential for 2.5 Dimensional Site Based on GIS

TANG Hao,CHEN Guo-xing

DOI: https://doi.org/10.3969/j.issn.1004-4574.2007.02.016

2007-01-01

Abstract:The empirical equation of cyclic resistance ratio of saturated sands with different probability level is utilized to evaluate the earthquake-induced sand liquefaction for 2.5D(2.5-dimensional) engineering site.By the Kriging interpolation method,the identification of sand liquefaction locality of the site can be estimated based on the evaluated results of liquefaction potential at the observation boreholes.Sustained by GIS 3D module,TIN(triangulated irregular network) surface and tetrahedron model are adopted to simulate the geologic body and realize the visibility of liquefaction potential for 2.5D engineering site.The research results show that(1)The Kriging interpolation is an effective method to estimate the liquefaction potential of the unidentified points by the evaluated liquefaction potential results of the observation boreholes.Therefore,it is a preferable way to evaluate the possible liquefaction range for engineering site.In addition,it has a bright application prospects in geotechnical investigation;(2)GIS 3D module is an effective way to realize the establishment of visibility model for site liquefaction potential.Therefore,the research on the 3D visibility for site liquefaction potential based on GIS is worthy of the further discussion.
Probabilistic Evaluation Of Earthquake-Induced Liquefaction Potential For Large Region Site Based On Two-Dimensional Gis Technique

Guoxing Chen,Hao Tang

DOI: https://doi.org/10.1007/978-3-540-79846-0_30

2008-01-01

Abstract:The empirical equation of cyclic resistance ratio CRR of saturated sands with different probability levels is utilized to evaluate the earthquake-induced sand liquefaction for 2D (two-dimensional) large region site. Based on GIS technique, the evaluation results of earthquake-induced liquefaction potential at the observation boreholes can be adopted as the "elevation" in digital elevation model, therefore the identification of liquefaction locality for 2D large region site can also be evaluated by Kriging interpolation method. The research in this paper shows that: (1) The Kriging interpolation is an effect method for evaluating the latent distribution of the site liquefaction potential beyond the observation boreholes. Thus, it is a preferable way to evaluate the possible liquefaction range for 2D large site. (2) Based on ArcGIS software, the Kriging method embedded in the "Spatial Analyst" extension module can be utilized to evaluate the liquefaction potential of the unidentified points by the evaluated results of the reconnaissance boreholes. Therefore, the 2D distribution map of the liquefaction potential for the large region site can be generated.
Evaluation Indexes of Sand Liquefaction Analysed by Rough Set

Nian Ping Liu,Hong Tu Wang,Zhi Gang Yuan

DOI: https://doi.org/10.4028/www.scientific.net/amr.243-249.3087

2011-01-01

Advanced Materials Research

Abstract:Sand liquefaction is a problem of complex evolution of the disaster, there is no accurate way to judge at present, this study put forward an analytical method to improve and optimize the evaluation system of sand liquefaction based on rough set. The significance of indexes are confirmed by calculating rough dependability between indexes and result for appraisement, the result show that SPT blow count has the greatest impact on the evaluation system, the groundwater level has greater impact, followed by the sand depth, epicenteral distance and duration. The proposed approach overcame the subjectivity of traditional weight determination method, so it is more objective and accurate, and it is reasonable and effective to optimize the evaluation index of sand liquefaction.
Risk evaluation of earthquake-induced site liquefaction based on 3D GIS

Hao Tang,Guo-xing Chen

2007-01-01

Abstract:Through Kriging interpolation method, the identification of liquefaction location at engineering site can be estimated based on the evaluated liquefaction potential at the observational boreholes. Sustained by GIS 3D module, the geologic body of site is. simulated and the visibility of 3D site liquefaction potential is realized too. The research shows that: a. Kriging interpolation is an effect method to evaluate the liquefaction potential of the unidentified points by using the evaluated results of the observational boreholes. Therefore, it is a preferable way to evaluate the possible liquefaction range for engineering site. b. GIS 3D module is effective to realize the establishment of visibility model for site liquefaction. Thus, the research in 3D visibility for site liquefaction based on GIS is worth of the further discussion.
GIS applied in 3D evaluation of earthquake-induced site liquefaction potential

Hao Tang,Guoxing Chen

2009-01-01

Geotechnical Engineering

Abstract:In recent years, GIS (Geography Information System) technique was widely applied in the evaluation of the earthquake-induced site liquefaction potential, for it has a strong ability to analyze site information spatially of. In this study, the deficiencies of 2D GIS technique applied in the visual evaluation of earthquake-induced site liquefaction potential were analyzed. Further, 2.5D and 3D modeling methods were introduced by actual engineering examples. First, DEM (Digital Elevation Model) tetrahedron extension technique was utilized to construct visual 2.5D model for site liquefaction potential sustained by GIS 3D module. Second, "block" data structure was adopted to describe the 3D site entity; thus, the visual 3D modeling for earthquake-induced site liquefaction potential can be realized based on Kriging method and volume rendering technique. The research shows that: a) 2.5D site liquefaction potential model possesses 3D visibility impression but can not give the 3D distribution characteristics of site liquefaction potential; and, b) by 3D interpolation method and volume rendering technique, the interpolation results can be displayed in different color label to simulate the 3D distribution of liquefaction potential visually. Therefore, the spatial analysis functions that can not be realized by 2D and 2.5D GIS techniques such as 2D profile cutting and 3D body incision etc. can be comprehended.
Probabilistic Estimation of Seismic Liquefaction Potential for Large Region Site Based on Two-Dimensional GIS Technique

TANG Hao,CHEN Guo-xing,LIU Jian-da

DOI: https://doi.org/10.3969/j.issn.1672-2132.2007.03.008

2007-01-01

Abstract:The empirical equation of cyclic resistance ratio CRR of saturated sands with different probability level is utilized to evaluate the earthquake-induced sand liquefaction for 2D large region site.By GIS technique,the evaluation values of seismic liquefaction potential at the observation boreholes can be adopted as the elevation in digital elevation model and then the identification of liquefaction locality for 2D large region site can also be estimated based on Kriging interpolation method.The research shows that: The Kriging interpolation is an effective method to estimate the latent distribution of the site liquefaction potential beyond the observation boreholes.So it is a preferable way to evaluate the possible liquefaction range for 2D large site.Based on ArcGIS software,the Kriging method embedded in the "Spatial Analysis" extension module can be utilized to evaluate the liquefaction potential of the unidentified points by the evaluated liquefaction potential results of the reconnaissance boreholes.Thus the 2D distribution map of the latent liquefaction potential for the large region site can be generated.
CONSIDERATIONS ON EVALUATION OF SITES LIQUEFACTION

佘跃心,刘汉龙,高玉峰

DOI: https://doi.org/10.3969/j.issn.0495-5331.2003.04.019

2003-01-01

Abstract:The impaction of solum depth and ground water level on critical standard penetration hammer is analyzed in detail, and misapprehensions about that large overburdened effective stress can make sands to liquefy easier are carried. New liquefaction index is presented on the basis of analyzing the liquefaction index of GBJ50011-2001. New liquefaction index has means of obvious probability, and can be applied to the evaluation of site liquefaction and risk decisions.
EVALUATION OF LIQUEFACTION OF SANDY SOILS BASED ON CONE PENETRATION TEST

蔡国军,刘松玉,童立元,杜广印

DOI: https://doi.org/10.3321/j.issn:1000-6915.2008.05.018

2008-01-01

Abstract:Soil liquefaction is a major concern for structures constructed on sandy and silty sites.Soil liquefaction is also a major design issue for large structures such as mine tailings impoundments and earth dams.Therefore,liquefaction evaluation plays an important role in seismic investigation and design of buildings.It is important to determine the soil stratigraphy and in-situ soil state for soil liquefaction.Because of the difficulty and cost constraint of obtaining high-quality undisturbed sand samples,the in-situ test is a perfect method to evaluate the potential for soil liquefaction.At present,numerous methods based on the cone penetration test(CPT) data have been developed for evaluating the potential of soil liquefaction,but the validity is still confused.As a new kind of in-situ test,the piezocone penetration test(CPTU),is receiving increasing attention for assessing the soil liquefaction potential because of its repeatability,reliability,continuous data tracing and cost effectiveness.The methods for evaluating liquefaction potential of soils using in-situ tests are reviewed based on the precious works.Two comprehensive CPTU-based methods for assessing liquefaction resistance of sandy soils are evaluated and compared on the basis of data collected on nine sites in Jining—Xuzhou Expressway,where the actual field performances against liquefaction from CPT data are used as referenced data.It is shown that Robertson method and Olsen method are considered to be fairly accurate in predicting liquefaction resistance of sandy soils.The Robertson method is slightly more accurate than the Olsen method.
Comprehensive evaluation of liquefaction potential for sandy soil of the highway bridge on Yangtze river site under ground surface 15m to 30m

Jianda LIU,Guoxing CHEN,Xuezhu LIU,Binghui WANG

DOI: https://doi.org/10.13197/j.eeev.2007.05.004

2007-01-01

Abstract:The different parameters are adopted, such as earthquake ground motion parameters, soil behaviour indexes and geological burying conditions, in the estimating methods for liquefaction potential of sandy soil in different seismic design codes and some typical estimating methods at home and abroad. So, there are some differences in evaluation results of sand liquefaction potential, when different estimating methods of liquefaction potential for sandy soils are applied in the identical engineering site. It is objective and necessary for multi-methodology in liquefaction estimation of sandy soil employed to give the appropriate and creditable comprehensive evaluation results of liquefaction potential for important engineering projects. In this paper, the estimating methods for liquefaction potential of sandy soils of code for seismic design of buildings in China, the typical estimating methods at home and abroad and the finite-element analysis method are employed in evaluating the liquefaction potential for sandy soils at a site of one highway bridge on Yangtze river under ground surface 15 m to 30 m, in combination with the vibration txiaxial test results. The appropriate and creditable comprehensive evaluation results of sandy soils liquefaction potential are given based on the methods mentioned above, through considering 5m depth and without regard to riverbed scour condition. Moreover, the evaluation standard of liquefied potential for sandy soils is provided including liquefaction, probably liquefied and non-liquefied.
A New Parameter to Evaluate Liquefaction Resistance of Saturated Sand under Complex Dynamic Stress Paths

Bo Huang,Xingyao Chen,Qingjing Wang,Daosheng Ling

DOI: https://doi.org/10.4028/www.scientific.net/amm.405-408.378

2013-01-01

Applied Mechanics and Materials

Abstract:Foundations are often subjected to complex dynamic stresses which result from ocean wave, vehicle or seismic loads. In this paper, four series of tests under different dynamic stress paths were carried out on Fujian standard sand with hollow cylinder apparatus, to investigate its liquefaction resistance. Test results showed different strength of specimens under different dynamic stress paths, when using the traditional evaluation index: maximum cyclic shear stress. A concept named as load efficiency ( E ) was proposed in this paper, which is defined as definite integral of dynamic shear stress on time in a single cycle. E is a new parameter to characterize liquefaction resistance of non-cohesive soil, attempting to normalize the effect of different shear modes, in which the shear stresses are constant or change periodically under different dynamic stress paths. Test results showed that in the isotropic consolidation condition, the relationship between E and failure cycle N f is nearly linear in the dual-log coordinate.
3D Visualization for Earthquake-Induced Site Liquefaction Potential Based on Volume Rendering and GIS Technology

CHEN Guo-xing,TANG Hao,LIU Jian-da

DOI: https://doi.org/10.3321/j.issn:1000-4548.2008.04.020

2008-01-01

Abstract:The researches on visual 3D modeling for the earthquake-induced site liquefaction potential are to resolve the problem of simulating the potential risk of earthquake-induced site liquefaction spatially by 3D reality graphics.And it could be applied to the urban earthquake prevention and disaster mitigation.Firstly,the empirical equation of cyclic resistance ratio of saturated sands with different probability levels was utilized to evaluate the earthquake-induced site liquefaction potential.Secondly,a block data structure was adopted to describe the 3D liquefaction potential entity.Thirdly,visual 3D visualization modeling for the earthquake-induced site liquefaction potential could be realized based on the Kriging interpolation method and volume rendering technique.It was shown that:(1) When the 3D liquefaction potential entity was partitioned by the block data model,the Kriging method can be adopted to realize 3D interpolation.Therefore,the latent distribution of the site liquefaction potential beyond the observation boreholes could be evaluated.(2) Based on the probability evaluation results and volume rendering technique,the Kriging interpolation results were displayed in different color marks to indicate the risk extent of the site liquefaction potential.Thereby,the spatial distributing characteristics and variety trend of the site liquefaction potential could be displayed in 3D graphic form.And also,the 2D profile section and 3D body incision could be generated automatically.
Evaluation Of Liquefaction Potential Of Saturated Sands Based On Resistivity Piezocone Penetration Testing

Guojun Cai,Haifeng Zou,Yan Yang,Songyu Liu,Anand J. Puppala

DOI: https://doi.org/10.1007/978-981-13-0095-0_40

2018-01-01

Abstract:The liquefaction of saturated soils is a major concern for the earthquake damage of foundation. Due to the difficulty and cost constraint in obtaining high-quality undisturbed samples, in-situ testing is commonly applied to evaluating the potential of soil liquefaction. In high risk projects, a comprehensive evaluation based on various methods is usually adopted, and thus the research on new method to evaluate the liquefaction is still necessary. In this research the feasibility of using resistivity piezocone penetration test (RCPTU) for predicting liquefaction resistance is investigated. The resistivity of saturated silts and sands is measured using RCPTU at a test section of Suqian-Xinyi expressway. First, the relationship between normalized cone tip resistance and resistivity is analyzed and can contribute to the evaluation of soil liquefaction based on resistivity. Second, the study on combination of resistivity and soil behavior type index to directly calculate the cycle resistance ratio (CRR) is conducted with the CRR from Robertson modified liquefaction evaluation model as reference. The influence of thin cohesive layers and transition zones is also analyzed. It is shown that the resistivity and soil behavior type index can be used for effective evaluation of liquefaction potential of saturated soils.
Numerical Analysis of Residual Pore Water Pressure Development and Evaluation of Liquefaction Potential of Seabed under Wave Loading

张晨明,王栋,郭莹,栾茂田

DOI: https://doi.org/10.3321/j.issn:0559-9350.2004.02.016

2004-01-01

Abstract:In order to clarify the mechanism of wave induced liquefaction of seabed,numerical analysis based on elastic theory is carried out to evaluate dynamic response of seabed under wave loading.The empirical pattern of pore pressure generation of sand under undrained cyclic shearing is incorporated with Biot's coupling equations which governing vibration and consolidation coupling effects of seabed.A numerical procedure based on FEM is developed to assess the residual pore pressure.The criterion for assessment of liquefaction triggering proposed by Zen and Yamazaki is revised and then the revised criterion is employed to predict the liquefaction potential of the seabed on the basis of computed pore pressure.
IMPROVEMENT OF SIMPLIFIED PROCEDURE FOR LIQUEFACTION POTENTIAL EVALUATION OF SANDS BY SHEAR WAVE VELOCITY

ZHOU Yan-guo,CHEN Yun-min,KE Han

DOI: https://doi.org/10.3321/j.issn:1000-6915.2005.13.028

2005-01-01

Abstract:Evaluation of soil liquefaction potential is an important aspect of geotechnical engineering practice;and several types of evaluating procedures have evolved over the past 30 years. In the current study,the simplified procedure using shear wave velocity measurements for liquefaction potential assessment was improved from the experimental results of undrained cyclic triaxial tests on saturated sands with shear wave velocity measured by bender elements. This improved simplified procedure establishes its correctness and feasibility essentially upon the warranted correlation between liquefaction resistance and elastic shear modulus of sandy soils,which is almost irrespective of soil types and confining pressures. Intensive evaluation of 26 earthquakes and more than 70 measurement sites shows that,the evaluation results using this improved simplified procedure are more consistent with the case history data than those from other evaluation methods within certain ranges of shear wave velocity. A case study is provided to illustrate application of the improved procedure. Additional studies are needed,especially for evaluating the liquefaction resistance of dense soil deposits shaken by stronger ground motions so as to further validate this improved simplified procedure.
A quantitative study of the effects of physical properties and external loads on the liquefaction of saturated sand based on an intelligent numerical cyclic triaxial test system

Wanqing Wu Shangwu Yu Yu Zhou Yueyang Sun Heping Wang Xiaoxiang Yu Zihao Zhao Qinggong Zheng a Marine Engineering College,Dalian Maritime University,Dalian,People's Republic of Chinab Engineering Technology Center for Ship Safety and Pollution Control,Dalian,People's Republic of China

DOI: https://doi.org/10.1080/17445302.2024.2365024

2024-06-15

Ships and Offshore Structures

Abstract:Soil liquefaction would cause significant damage to the safety of cargo transportation. The aim of this article is to conduct a quantitative study of the influence of the main physical characteristic parameters of saturated sand and external loads on its liquefaction. On the basis of the physical cyclic triaxial test (CTT), the finite element simulation model and PSO-BP neural network prediction model and importance analysis model were optimised in this study. Based on this, an innovative intelligent numerical CTT system for saturated sand was constructed. The research results indicate the influence of external load, effective internal friction Angle and plasticity index on the liquefaction of saturated sand is significant, and the average weight is 40.15%, 29.15% and 25.05%, respectively. In this paper, the relevant research provides a theoretical basis for effective control of sand liquefaction and provides new ideas and feasible solutions for subsequent research on sand liquefaction.

engineering, marine

Evaluation of sand liquefaction under the GIS environment

Characterizing the Liquefaction Potential and Pore Pressure Generation of Silty Sands Through the Energy-Based Approach in the Framework of Critical State Soil Mechanics

Analysis for Influence of Multi-Layered Soil Stratum on Sand Liquefaction

Liquefaction Analysis By Gis Method

Spatial distribution simulation method for liquefaction index probability

Risk-evaluating System of Seismic Site Liquefaction Based on GIS Technique:A Primary Research

Probabilistic Estimation of Seismic Liquefaction Potential for 2.5 Dimensional Site Based on GIS

Probabilistic Evaluation Of Earthquake-Induced Liquefaction Potential For Large Region Site Based On Two-Dimensional Gis Technique

Evaluation Indexes of Sand Liquefaction Analysed by Rough Set

Risk evaluation of earthquake-induced site liquefaction based on 3D GIS

GIS applied in 3D evaluation of earthquake-induced site liquefaction potential

Probabilistic Estimation of Seismic Liquefaction Potential for Large Region Site Based on Two-Dimensional GIS Technique

CONSIDERATIONS ON EVALUATION OF SITES LIQUEFACTION

EVALUATION OF LIQUEFACTION OF SANDY SOILS BASED ON CONE PENETRATION TEST

Comprehensive evaluation of liquefaction potential for sandy soil of the highway bridge on Yangtze river site under ground surface 15m to 30m

A New Parameter to Evaluate Liquefaction Resistance of Saturated Sand under Complex Dynamic Stress Paths

3D Visualization for Earthquake-Induced Site Liquefaction Potential Based on Volume Rendering and GIS Technology

Evaluation Of Liquefaction Potential Of Saturated Sands Based On Resistivity Piezocone Penetration Testing

Numerical Analysis of Residual Pore Water Pressure Development and Evaluation of Liquefaction Potential of Seabed under Wave Loading

IMPROVEMENT OF SIMPLIFIED PROCEDURE FOR LIQUEFACTION POTENTIAL EVALUATION OF SANDS BY SHEAR WAVE VELOCITY

A quantitative study of the effects of physical properties and external loads on the liquefaction of saturated sand based on an intelligent numerical cyclic triaxial test system