Abstract:High-entropy CoCrFeMnNi alloy/aluminide-laminated composites were produced via the hot pressing diffusion sintering method at 1000 ℃. The results revealed that the aluminide structure layer based on the Al13(Cr, Mn, Fe, Co, Ni)4 phase first transforms into Al8(Cr, Mn, Fe, Co, Ni)5 phases with a trigonal crystal structure and then gradually transitions into Al(Cr, Mn, Fe, Co, Ni) phases with a B2 cubic crystal structure under high-temperature annealing. During high-temperature annealing, the elements Ni, Co, and Fe exhibit higher diffusion rates and diffusion amounts in the aluminide layer. The transformation of the aluminide layer is mainly influenced by the diffusion behavior of these elements. The absence of an oxidation interface barrier during high-temperature annealing results in multiple diffusion mechanisms, leading to the predominance of lattice diffusion and interface diffusion, which control the growth kinetic of the Al(Cr, Mn, Fe, Co, Ni) phase layer. The hardness indentation of the B2-Al(Cr, Mn, Fe, Co, Ni) phases, obtained by high-temperature annealing, shows no cracks and exhibits a multi-slip system characteristic of ductile aluminum compounds. This ductile behavior helps to reduce the deformation resistance in the hard and brittle layer and decreases the likelihood of delamination failure during plastic deformation. The bending strength of high-entropy/aluminide-layered (HAL) composite materials after high-temperature annealing reaches 1000 MPa, with the main energy dissipation modes being the plastic deformation of the ductile layer and fracture of the hard and brittle layer. Dynamic impact failure forms mainly include plastic deformation and delamination, with impact strength and energy consumption reaching 2317 MPa and 4750 J/mm3, respectively. This study provides phase formation sequence and dynamic mechanical properties of high-entropy CoCrFeMnNi/B2 structure aluminide-laminated composites which proved to be a new type of composites with good impact resistance.Graphical Abstract

Characteristics of Fe-rich Intermetallics Compounds and Their Influence on the Cracking Behavior of a Newly Developed High-Pressure Die Cast Al–4Mg–2Fe Alloy

The Microstructure characteristics and fracture behavior of the polyhedral primary iron-rich phase and plate-shaped eutectic iron-rich phase in a high-pressure die-cast AlSi10MnMg alloy

On the characterization of primary iron-rich phase in a high-pressure die-cast hypoeutectic Al-Si alloy

The characterization of Fe-rich phases in a high-pressure die cast hypoeutectic aluminum-silicon alloy

Microstructural Evolution and Elevated-Temperature Strengthening Mechanism of Co-free FeCrMnNiV0.2Alx High-Entropy Alloys During Annealing

Preparation and properties of FeNiMnCuC0.2Alx high-entropy alloy

Microstructure and mechanical properties of Al-Fe-Co-Cr-Ni high entropy alloy fabricated via powder extrusion

Effect of Fe, Mn, Ce on the Microstructure and Mechanical Properties of Al-Mg and Al-Mg-Si Die Casting Alloys

Investigation of mechanical behavior, constitutive modeling, and fracture criteria for as-cast Al0.3CoCrFeNi high entropy alloy

Characterization of high-pressure die-cast hypereutectic Al-Si alloys based on microstructural distribution and fracture morphology

Revealing the influence of Fe on Fe-rich phases formation and mechanical properties of cast Al-Mg-Mn-Fe alloys

Enhanced ductility in high-pressure die casting Mg-4Ce-xAl-0.5Mn alloys via modifying second phase

Characterization of externally solidified crystals in a high-pressure die-cast AlSi10MnMg alloy and their effect on porosities and mechanical properties

The Microstructures and Properties Changes Induced by Al:Co Ratios of the Al CrCo FeNi High Entropy Alloys

On the characterization of microstructure and fracture in a high-pressure die-casting Al-10 <i>wt</i>%Si alloy

Influence of Introducing Zr, Ti, Nb and Ce Elements on Externally Solidified Crystals and Mechanical Properties of High-Pressure Die-Casting Al–Si Alloy

High-entropy CoCrFeMnNi alloy/aluminide-laminated composites with enhanced quasi-static bending and dynamic compression properties

Microstructure and Impact Behavior of Mg-4Al-5RE-xGd Cast Magnesium Alloys

Forming mechanism of equilibrium and non-equilibrium metallurgical phases in dissimilar aluminum/steel (Al–Fe) joints

The roles of solidification cooling rate and (Mn,Cr) alloying elements in the modification of β-AlFeSi and hardness evolvements in near-eutectic Al-Si alloys

Effects of Aluminum on Microstructure and Compressive Properties of Al-Cr-Fe-Ni Eutectic Multi-Component Alloys