Microtexture, seismic rock physical properties and modeling of Longmaxi Formation shale
Deng Ji-Xin,Wang Huan,Zhou Hao,Liu Zhong-Hua,Song Lian-Teng,Wang Xu-Ben
DOI: https://doi.org/10.6038/cjg20150626
2015-01-01
Abstract:Longmaxi Formation shale of Sichuan Basin is a typical shale-gas system in which the rock is the source, reservoir, and seal, and is also the most important horizon for gas shale exploration in China. The elastic properties of shale rocks vary significantly between reservoirs and within a reservoir due to the wide variety of material composition and fabric anisotropy. The rock properties and corresponding seismic rock-physics properties are not completely known for the Longmaxi Formation shale, thus related theoretical and experimental investigations are crucial for seismic exploitation of shale gas reservoirs and corresponding hydraulic fracturing. The mineralogy and the organic content were determined through powder XRD analysis. Seismic rock-physics properties and their impact factors of the gas shale samples from Longmaxi Formation are analyzed based on acoustic experiments and microtexture analysis with the combined application of SEM and CT scanning, and the rock-physics model for shale is also proposed. Cylindrical cores of a suite of shales from this formation with different organic matter contents were cut and oriented carefully in the direction normal, parallel, and at 45 degrees to bedding planes, and velocities were measured using the ultrasonic transmission technique at a range of confining pressures, which can be used to determine the stiffness and anisotropy properties of rock samples. The results show that the TOC (total organic content) and porosity are controlled to some degree by the quartz content, and TOC and pyrite are mainly located in the pore space, and are not the load-bearing grains. Shale samples can be classified as silica-rich rock. The constitution of the rock frame is also governed by the clay or quartz content, and the rock samples are clay-supported when the clay content is larger than 30% or the quartz content lower than 40%, and quartz combined with clay becomes load-bearing material when clay content is lower than this value. Thus, the seismic properties of those shale samples are controlled by load-bearing grains, TOC and porosity. We observe a "V" shaped trend of P-wave impedance as function of quartz content: P-wave impedance decreases as the quartz content increases till about 50%, after the turning point, the P-wave impedance increases again. Organic-rich shale shows low P-wave impedance and V-P/V-S ratio due to relatively higher TOC and quartz content. Nonetheless, high P-wave impedance is also observed when the quartz content is very high resulting from the variation of load-bearing grains. Preferential alignment of mineral grains is the dominant factor to create the elastic anisotropy of these shale samples at high confining pressure. A strong positive correlation is found between the anisotropy parameters (epsilon, gamma) and the clay content, which follows an empirical exponential relationship: epsilon = 0. 0016V(clay)(1.32), gamma= 0. 0015V(clay)(1.33). Samples with low clay content show negative epsilon and gamma due to the vertically aligned microcracks. C-11, C-33, C-44, C-66 and C-13 are five elastic stiffness constants of typical transverse isotropic media, which also show apparent empirical correlations. Among these, C-13 and C-33 C-44 satisfy an empirical relationship: C-13 = 1. 11C(33)-2C(44), and C-13 and C-12 satisfy an empirical relationship: C-13 = 1. 13C(12). By combined usage of the Self Consistent Approximation (SCA), Differential Effective Medium and the Backus average method to describe the microtexture of shale sample properly, the prediction results of the model fit very well with those measured data at lab and well-logging data, which proves the practicality of the model. Longmaxi Formation shale is variation in mineral composition, organic content and microtexture due to complex depositional and digenetic evolution, which is likely to attributed to the significant difference in seismic rock physics and mechanical properties. Our results can also provide basis for well-logging interpretation and "sweet spot" discrimination by the seismic method for Longmaxi Formation shale.