Abstract:Poly(L‐lactide) (PLLA), poly(D‐lactide) (PDLA) and poly(methyl methacrylate) (PMMA) are melt blending with various content of PDLA (0 and 3 wt%) and PMMA (0–20 wt%). The blending pellets then undergoes the melt spinning and hot drawing process to prepare PLA composite fibers. The hydrolysis resistance of fibers is improved by the addition of PMMA and the mechanical property and heat resistance properties increased for the highly oriented crystalline morphology induced by the stereocomplex crystals (SC), which have formed in PLLA/PDLA/PMMA fibers. The SC nanofibrils are detected from the surface morphology of PLLA/PDLA/PMMA fibers after hydrolysis at 60°C for 132 h in NaOH solution. Polylactic acid/poly(methyl methacrylate) (PLA/PMMA) composite fibers with high performance were fabricated using melt spinning technique. The crystallization, lamellae orientation and physical properties of composite fibers were investigated systematically. The addition of PMMA (0–20 wt%) has improved the hydrolysis resistance of composite fibers by preventing water molecules from penetrating and diffusing through the fibers, but the strength and heat resistance were reduced at the same time. The stereocomplex crystallites (SC) formed before spinning by introducing poly(D‐lactide) (PDLA) (3 wt%) in poly(L‐lactide) (PLLA) matrix and acted as nucleating agents to enhanced the crystallization and lamellae orientation of PLLA matrix, which improved the physical properties of PLA composite fibers resultful. The tensile strength of PLA fibers with 3 wt% PDLA and 5 wt% PMMA was increased 31% as well as the boiling water shrinkage and the hydrolysis rate were decreased 30% and 33% in relation to PLLA fibers. Finally, the hydrolysis resistance was further enhanced on the basis of realizing high strength and heat resistance, which is of great significance for preparing durable PLA fiber materials and expanding their application.

Fused Deposition Modeling of Poly (lactic Acid)/almond Shell Composite Filaments

On Almond Skin Powder Reinforced PA6 Composite for 3D Printing Applications

A Surface Modification of Polylactic Acid Composites for Additive Manufacturing with Modified Chopped Carbon Fiber and Modified Nano‐hydroxyapatite

Blending and functionalisation modification of 3D printed polylactic acid for fused deposition modeling

Numerical Calculation and Properties Study on Polylactic Acid (Pla)/nano-Hydroxyapatite (N-Ha) Composite Fluid 3D Printed by Fused Deposition Modeling

Lifting the quality of fused filament fabrication of polylactic acid based composites

Investigation into hydroxypropyl-methylcellulose-reinforced polylactide composites for fused deposition modelling

Reinforcement of Polylactic Acid for Fused Deposition Modeling Process with Nano Particles Treated Bamboo Powder

Carbon Fiber-Reinforced PLA Composite for Fused Deposition Modeling 3D Printing

Study on properties of polylactic acid/lemongrass fiber biocomposites prepared by fused deposition modeling

Preparation of Poly(vinyl Alcohol)/poly(lactic Acid)/hydroxyapatite Bioactive Nanocomposites for Fused Deposition Modeling

Development and Application of Wood Flour-Filled Polylactic Acid Composite Filament for 3D Printing

Toward durable polylactic acid/poly(methyl methacrylate) polyblend fibers with high performance

Comparative Investigations on Properties of Three Kinds of FDM 3D-Printed Natural Plant Powder/Poly(lactic acid) Biocomposites

Effect of Chemical Treatment of Sugar Palm Fibre on Rheological and Thermal Properties of the PLA Composites Filament for FDM 3D Printing

Atomic-scale and Experimental Investigation on the Micro-Structures and Mechanical Properties of PLA Blending with CMC for Additive Manufacturing

Mechanical and Wear Characteristics Investigation on 3D Printed Silicon Filled Poly (Lactic Acid) Biopolymer Composite Fabricated by Fused Deposition Modeling

Preparation Of Plasticized Poly (Lactic Acid) And Its Influence On The Properties Of Composite Materials

Effects of fabrication parameters on the mechanical properties of short basalt-fiber-reinforced thermoplastic composites for fused deposition modeling-based 3D printing

Effects of Rice Straw Powder (RSP) Size and Pretreatment on Properties of FDM 3D-Printed RSP/Poly(lactic acid) Biocomposites

Sustainable improvement in the polylactic acid properties of 3D printing filaments: The role of bamboo fiber and epoxidized soybean oil‐branched cardanol ether compatibilizer