Abstract:The effect of coating cracking during depth-sensing indentation testing (e.g. nanoindentation testing) on systems comprising thin hard coatings (e.g. TiN) on a less stiff, hard substrate (e.g. steel) has been investigated in order to establish whether, at such small scales, the occurrence of annular through-thickness cracks around indentation sites can be detected from load–displacement plots and whether any accompanying localized debonding of the coating from the substrate can also be identified. Experiments were performed on thin TiN and NbN monolayers, and compositionally modulated TiN/NbN and TiN/ZrN deposited onto hard steel or stainless steel substrates. Above a critical load (Pcrit) in the range 80–500mN, all systems exhibited annular through-thickness cracks around indentation sites. The cracking was found to be accompanied by a discrete change in gradient of the loading portion of the load–displacement curve. Also, analysis of the unloading curves beyond this point showed that elastic recovery was controlled by the elastic modulus of the underlying substrate material alone. The cracking mechanism has been characterized using scanning electron microscopy, coupled with optical profilometry to map the detailed z-displacement of the surface — a procedure critical to understanding whether coating–substrate debonding had occurred. Some cracks were found to show a spiral morphology and the effect of indentation loading rate was investigated to see if appearance of these cracks was loading-rate sensitive. Our results highlight the problems inherent in assessing both the interfacial failure and the interfacial fracture toughness of thin film coated systems at the small contact scales (⩽1μm) associated with crack genesis where it is difficult to confirm the extent of sub-surface cracks by conventional means. We have also demonstrated that both load–displacement and load–displacement squared plots are necessary if a more complete understanding of system behaviour is to be gained. Also, a simple fracture mechanics model for the annular cracking behaviour seen in such systems has been derived and used to estimate a value of Gic (the interfacial work of fracture) as 180Jm−2 for the TiN/ZrN-stainless steel system.

Weakening effect of plastic yielding inception in thin hard coating systems*

Experimental study of a potential weakening effect in spheres with thin hard coatings

Indentation pop-in as a potential characterization of weakening effect in coating/substrate systems

Design for Manufacturing of Cemented Carbide Coated Components Toward High Wear and Impact Resistance Performance

Effects of Elastic Modulus Mismatch Between Coating and Substrate on the Friction and Wear Properties of TiN and TiAlN Coating Systems

Cleavage Cracking of Ductile-Metal Substrates Induced by Brittle Coating Fracture

The effect of the substrate on the mechanical properties of TiN coatings

On the Surface and System Performance of Thermally Sprayed Carbide Coatings Produced under Controlled Residual Stresses

Stress-sensitive fatigue crack initiation mechanisms of coated titanium alloy

Internal Stress on Adhesion of Hard Coatings Synthesized by Multi-Arc Ion Plating

EFFECTIVE MECHANICAL PROPERTY OF NANO COATED FIBER REINFORCED COMPOSITES DUE TO INTERFACE STRESS

Degradation Damage of Stress Corrosion in Epoxy Zinc-Rich Coating/Steel Substrate Systems

The effect of coating cracking on the indentation response of thin hard-coated systems

Strengthening mechanisms of AlCoCrFeNi-WC-Ti coating from first-principles calculations

Plastic Strain Effect in Progressive Multi-Cycle Nano-Indentation Measurement

The investigation of support effect from hard substrate to soft coating of PI/EP-PTFE under different coating thicknesses and frictional contacts

Influences of Interface Properties and Coating Thickness on Fracture Behaviors of Coating/substrate Systems

Enhancing mechanism of TC4 high-cycle fatigue performance by the introduction of hard nitride mono-and multilayer coatings

Analysis Of The Mechanical Properties Of Tin/Ti Multilayer Coatings Using Indentation Under A Broad Load Range

Influence of coating thickness and temperature on mechanical properties of steel deposited with Co-based alloy hardfacing coating

Effect of Coating Thickness on the Stress Distribution in Hip Implants