Abstract:In this study, a constitutive model based on microscopic physical mechanism of silicone rubber foams was established. A theoretical statistical model of rubber elasticity considering the effect of dangling chains was modified to build this model. When a strain amplification factor (X) was introduced, the theoretical model could fit the tensile stress-strain data of mono- and bi-modal foam matrix well (Adj. R-Square = 0.9989, 0.9983). Parameters related to the polymer network, namely, average molecular weight (Mc) and volume fraction (ϕ) of chain segments between adjacent cross-linking points (network strands), were calculated by probabilistic method from the number-average molecular weight (Mn), vinyl content (wVi) of the primary polysiloxanes and percent conversion (q) of vinyl groups. The primary and infinite strain amplification factors (X0, X∞) and decay exponent (z), introduced by X and related to the nanoparticles, were obtained by fitting. Inspired by the fact that the actual strain of matrix was lower than that of the foams’, we introduced another item, strain hysteresis item (H, related with the foam porosity and cell structure), into the statistical model as well. With the same above values of Mc, ϕ, X0 and X∞, the model could also fit the compressive stress-strain data of mono- and bi-modal foams well (Adj. R-Square = 0.9948, 0.9985). Interestingly, the strain hysteresis items of the mono- and bi-modal foams almost completely coincided under all experimental strains, which may be attributed to the almost equal porosity and similar cell structure of the two foams. This constitutive model may connect the macroscopic stress-strain behaviour to the parameters of microscopic molecular structures, promisingly providing a basis for the performance improvement and optimization of silicone rubber foams.

How the Aggregates Determine Bound Rubber Models in Silicone Rubber? A Contrast Matching Neutron Scattering Study

Micromechanical Investigation of the Shear Behaviors of Sand‒rubber Mixtures Using a Multibody Meshfree Method

Correlation Between Mechanical Properties and Microscopic Structures of an Optimized Silica Fraction in Silicone Rubber

Effects of Various Filler Surfaces on Tuning the Hierarchical Structures and Reinforcement of Silicone Rubbers

Understanding the Reinforcement Effect of Fumed Silica on Silicone Rubber: Bound Rubber and Its Entanglement Network

Structural analyses of the bound rubber in silica-filled silicone rubber nanocomposites reveal mechanisms of filler-rubber interaction

Linear Rheology of Natural Rubber Compounds Filled with Silica, Short Nylon Fiber or Both

Control of basic aggregate structure: Application and mechanism analysis in nitrile rubber composite materials

Effect of Fumed Silica Aggregate on Filled Silicone Rubber Properties

Dynamics Heterogeneity in Silica‐filled Nitrile Butadiene Rubber

Reinforcement mechanism of silica surface hydroxyl: The opposite effect

Fraction-Dependent Filler Network in Silicone Rubber: Unraveling Abrupt Enhancement in Rheological Properties via Solvent Extraction and DLS Study

Bound Rubber at Interface of Silicon Rubber Reinforced by Fumed Silica Nanoparticles

Understanding the Effect of Filler Shape Induced Immobilized Rubber on the Interfacial and Mechanical Strength of Rubber Composites

Studies on Multilayer Microstructure of Nanosilica Filled Carboxylated Styrene-Butadiene Rubber

Study on structures, dynamics and mechanical properties of styrene butadiene rubber (SBR)/silica interfaces: A fully atomistic molecular dynamics

Linear and nonlinear rheological behaviors of silica filled nitrile butadiene rubber

Establishment of Constitutive Model of Silicone Rubber Foams Based on Statistical Theory of Rubber Elasticity

Formation mechanism of bound rubber in elastomer nanocomposites: a molecular dynamics simulation study

Processing Rheological Behavior of Functionalized Silica/natural Rubber Composites

Effects of rubber/filler interactions on the structural development and mechanical properties of NBR/silica composites