Abstract:Abstract High-pressure axial piston pumps operate in high-speed and high-pressure environments. The contact state of the slipper against the swashplate can easily change from an oil film lubrication to a mixed oil film/asperity contact, or even dry friction. To improve the dry friction performance of slipper pairs and to avoid their potentially rapid failure, this study examined the effects of material matching on the dry friction performance of the slipper pair for high-pressure axial piston pumps. A FAIAX6 friction and wear tester was developed, and the dry friction coefficients of the slipper pairs matched with different materials were studied using this tester. Based on the thermo-mechanical coupling of the slipper pair with the working process, the contact surface temperatures of the slipper pairs matched with different materials were calculated and analyzed for the same working conditions. Following this, the effects of the material properties on the temperature increase at the slipper sliding contact surfaces were revealed. The reliabilities of the temperature calculations and analysis results were verified through orthogonal tests of slipper pairs matched with different materials. The results indicate that the influence of the material density on the friction coefficient is greater than that of the Poisson’s ratio or the elastic modulus, and that the slipper material chosen should have a high thermal conductivity, low density, and low specific heat, whereas the swashplate material should be high in specific heat, density, and thermal conductivity; in addition, the slipper pair should be a type of hard material to match the type of soft material applied; that is, the hardness of the swashplate material should be greater than that of the slipper material.

Fully-coupled Thermomechanical Analysis for Sliding Contact Between Textured Slipper and Swashplate in Axial Piston Pump

Fluid-solid coupling analysis for hydrostatic supporting slipper pair of axial piston pump for seawater desalination

Investigation on Structural Optimization of Anti-Overturning Slipper of Axial Piston Pump

Study on friction performance and mechanism of slipper pair under different paired materials in high-pressure axial piston pump

Numerical and Experimental Research on Engagement Process of Wet Multi-Plate Friction Clutches with Groove Consideration

Thermo-mechanical Coupling Analysis of a High-Speed Actuating Mechanism Based on a New Thermal Contact Resistance Model

A Study on Heat Transfer Model for the Dynamic Contact Boundary Between Piston Ring and Cylinder Liner

FEM Based Simulation Study on Static and Dynamic Properties of Port Plate in Axial Piston Pump

Multi-objective Optimization of Surface Texture for the Slipper/swash Plate Interface in EHA Pumps

Numerical Simulation of Overturning Phenomenon of Axial Piston Pump Slipper Pair

A New Coupled Dynamic Model to Study the Vibration and Lubrication Characteristics of Slipper/Swash-Plate Interface in an Axial Piston Pump

Thermo-Mechanical Coupling Analysis of the Actuating Mechanism in a High Speed Press

Life Cycle Assessment of a Slipper/swash Plate Friction Pair Based on Thermal-Fluid-structure Lubrication State Dynamic Recognition

Impact of the Thermal Effect on the Load-Carrying Capacity of a Slipper Pair for an Aviation Axial-Piston Pump

A Novel Model for Predicting Thermoelastohydrodynamic Lubrication Characteristics of Slipper Pair in Axial Piston Pump

Study on the Load-Carrying Capacity of Surface Textured Slipper Bearing of Axial Piston Pump

Thermal-fluid-structure coupling analysis for valve plate friction pair of axial piston pump in electrohydrostatic actuator (EHA) of aircraft

Relative motion relationship and collision mechanism of slipper-retainer assembly of axial piston machines

Effects of Surface Roughness on the Mixed Thermal Elstohydrodynamic Lubrication Characteristics of Surface Textured Slipper Bearing in Axial Piston Pump

Structural Design of a Cross Wobble Plate Driving Axial Piston Pump Based on ADAMS and AMESim Co-simulation

Modeling and Analysis of the Churning Losses Characteristics of Swash Plate Axial Piston Pump