Abstract:Recently, various miniaturized electronic systems and the rapid increase in power density of microelectronic devices have created additional requirements for micro-scale heat dissipation technology. To dissipate heat in a micro-scale region efficiently, several creative cooling methods for high heat flux dissipation have been designed on the order of 1000 W/cm(2). Due to its high surface-to-volume ratio, the microchannel heat sink has become the most popular one among emerging technologies and an effective tool for high heat flux thermal management. Nevertheless, in common electronic microchannel cooling systems, the traditional parallel microchannel causes a dramatic pressure loss along channel length. In this regard, the manifold microchannel heat sink cooling technology becomes promising with its high heat dissipation potential and moderate pressure drop penalty. The shortened effective flow length compared with the traditional microchannel provides a smaller pressure drop and delays the onset of the critical-heat-flux point. However, while a number of numerical and experimental studies have been conducted for the single-phase flow in the manifold microchannel, two-phase flow boiling in this kind of channel is not widely employed because of its issues with flow pattern prediction. This work develops a new solver based on open source software OpenFOAM to perform the transient process of subcooled flow boiling in the manifold microchannel heat sink. Additionally, heat transfer in the silicon substrate is considered to improve the accuracy of simulation. Similar to single-phase flow simulation for the manifold microchannel, a unit cell model extracted from the whole cooling plate is employed for the two-phase boiling flow to avoid huge computational costs. Through several reasonable assumptions, the symmetry boundary condition is applied on four lateral surfaces in the unit cell, while uniform heat flux is adopted on the bottom wall. A uniform inlet velocity boundary estimated from the total volume flow rate condition is coupled with a fixed temperature value of 7 degrees C lower than saturation temperature. After the mesh independence test, the self-programming solver and numerical methods are validated by comparing numerical results with experimental data. It is determined that the boiling curve obtained by the empirical rate phase-change model with parameters r(1)=r(v)=100 agrees well with experimental results. Furthermore, heat transfer and pressure drop performance differences are caused by microchannel width w(c) and fin width w(f). In comparison to sample A (w(c)=w(f)=15 mu m), decreasing wc and wf simultaneously leads to lower average wall temperature of the heated surface; the channel pressure drop between inlet and outlet surfaces rises dramatically when the widths decrease. When the total number of microchannels in the manifold microchannel cooling plate remains unchanged, increasing wc results in a decreased wf. Based on experimental results, heat sink sample C shows that the pressure loss can be considerably reduced under the premise of sacrificing a small degree of heat transfer performance, which can be attributed to the increased microchannel hydraulic diameter. The manifold microchannel heat sink with w(c)>w(f) is recommended for practical application due to lower pressure loss and average temperature variation.

Simulation and Verification of Pressure Drop in Silicon Microchannel Based on Porous Model Equivalence

PRESSURE FLUCTUATIONS OF LIQUID-LIQUID SLUG FLOW IN CROSS-JUNCTION SQUARE MICROCHANNELS

Simulation of Couette Flow Using Conventional Burnett Equations with Modified Slip Boundary Conditions

SIMULATION AND MICRO-PIV RESEARCH ON CLASSICAL MICROCHANNEL FLOW

Numerical Simulation on Pressure Drops for Air-Water Two-Phase Flow in Micro-Channels

An Experimental Investigation on Pressure Drop of Steam Condensing in Silicon Microchannels

Study on Flow Characteristics of Working Medium in Microchannel Simulated by Porous Media Model

Numerical Simulation of Subcooled Flow Boiling in a Manifold Microchannel Heat Sink

Effects of Distribution Channel Dimensions on Flow Distribution and Pressure Drop in a Plate‐Fin Heat Exchanger

Simulation and Analysis of a Micro-Fluidics Cooling System

Numerical Investigation of Heat Transfer and Pressure Loss of Double-Layer Microchannels for Chip Liquid Cooling

Computational Study and Optimization of Laminar Heat Transfer and Pressure Loss of Double-Layer Microchannels for Chip Liquid Cooling

An Experimental Investigation Of Flow Characteristics For Laminar Flow In Silicon Microchannels

Numerical Simulation of Liquid Film Thickness and Pressure Drop in Microchannel Slug Flow

Thermal Analysis and Experimental Validation of Laminar Heat Transfer and Pressure Drop in Serpentine Channel Heat Sinks for Electronic Cooling

Numerical Study of Laminar Heat Transfer and Pressure Drop Characteristics in A Water-Cooled Minichannel Heat Sink

An experimental study of two-phase pressure drop of acetone in triangular silicon micro-channels

Characterization on the Performance of a Fractal-Shaped Microchannel Network for Microelectronic Cooling

A new stepped-channel liquid cooling plate thermal management system combined with composite phase change materials

Performance analysis on the liquid cooling plate with the new Tesla valve capillary channel based on the fluid solid coupling simulation

Numerical Simulation of Flow Characteristic in Microchannel Between Parallel Flat Plates