Abstract:Phase change phenomena in microchannels have been projected as an effective option for thermal management of various microscale systems. However, for the design of heat sinks which utilize these phenomena, a clear understanding of the physical mechanisms involved, in the microscale domain, is required. In the present study, a numerical simulation is carried out to predict the characteristics of two phase flow with liquid to vapor phase change, in rectangular microchannels for a range of hydraulic diameters. The annular flow pattern, reported to be the most common in microchannel, has been investigated, with water as the flowing medium. The analysis considers, among other parameters, the effect of surface tension on the flow dynamics, which could be significant in microchannels. The mathematical model is numerically solved using a quasi-three dimensional approach, incorporating the variations in the cross-sectional areas of both the phases along the flow direction. Since it is expected that the continuum approximation may be insufficient in the vapor domain in channels of very small dimensions, an analysis incorporating slip flow at the liquid vapor interface analysis has been performed, where the channel dimensions produce Knudsen number values in the range 0.001–0.1, as suggested in the literature. The liquid film thickness along the flow direction is determined utilizing mass conservation, and the velocity distributions at different locations along the flow direction are obtained by solving the governing differential equations numerically. The two phase pressure drop is calculated for cases demanding slip and no slip conditions. A comparison has been made of the fluid flow characteristics, between the slip and no slip cases for the cases where slip flow is expected. The effects of the imposed heat flux, volume flow rate and channel geometry on the velocity distribution and pressure drop are examined. The predicted pressure drop values are found to increase with increasing heat flux, and decrease with an increase in the flow rate and the channel height. The two phase heat transfer coefficient and the wall temperature of the channel are also determined. The two phase heat transfer coefficient is found to increase with an increase in the vapor quality. It is also noticed that the wall temperature decreases along the length of the channel and the wall temperature at the exit of the channel decreases with decrease in volume flow rate, within the range of parameters used, which is in accordance with observations reported in the literature. The results are found to be in good agreement with the experimental and theoretical results available in the literature.

Numerical Investigation of Heat Transfer and Pressure Loss of Double-Layer Microchannels for Chip Liquid Cooling

Computational Study and Optimization of Laminar Heat Transfer and Pressure Loss of Double-Layer Microchannels for Chip Liquid Cooling

An Experimental Study of Microchannel and Micro-Pin-Fin Based On-Chip Cooling Systems with Silicon-to-Silicon Direct Bonding.

Investigation of Embedded Microchannel Heat Transfer Performance Based on High Power Integrated Chip

Numerical Analysis of Microchannels Designed for Heat Sinks

Numerical Study on Heat Transfer Efficiency and Inter-Layer Stress of Microchannel Heat Sinks with Different Geometries

Simulation of fluid flow and heat transfer in microchannel cooling for LTCC electronic packages

Experimental and Numerical Studies of Fluid Flow Confined in Microchannel

Numerical Investigation of Fluid Flow and Heat Transfer in High-Temperature Wavy Microchannels with Different Shaped Fins Cooled by Liquid Metal

Numerical Analysis of Flow Boiling Characteristics of a Single Channel Heat Sink Subjected to Multiple Heat Sources

Numerical Study on Hybrid Discontinuous Microchannel Heat Sink Combining Manifold with Pin Fins (DMC-MPF) for High Power Electronic Device

Experimental and Numerical Study of Transient Electronic Chip Cooling by Liquid Flow in Microchannel Heat Sinks

Numerical evaluation on the heat dissipation capability of liquid metal based chip cooling device

Embedded microfluidic cooling with compact double H type manifold microchannels for large-area high-power chips

Numerical Analysis of Fluid Flow and Heat Transfer Characteristics of Novel Microchannel Heat Sink

Comparison of cooling performance of nanofluid flows in mini/micro-channel stacked double-layer heat sink and single-layer micro-channel heat sink

Numerical simulation of fluid flow and heat transfer in microchannels with patterns of hydrophobic/hydrophilic walls

On Numerical Simulation Techniques of Stable Crack Growth

High performance heat sink with counter flow diverging microchannels

Flow and Heat Transfer Performances of Liquid Metal Based Microchannel Heat Sinks under High Temperature Conditions

Numerical Investigations of the Thermal-Hydraulic Characteristics of Microchannel Heat Sinks Inspired by Leaf Veins