Abstract:Successful preparation of photopolymerizable ceramic slurries using non-oxide ceramics and their 3D printing is highly challenging as the ceramic powders often possess high UV-light absorbance. Even though pre-oxidation of the powders could improve the slurry printability, the residual oxygen element in the material would eventually deteriorate the material purity and performance. In this study, a separated redox route (pre-oxidation, 3D printing and carbothermal reduction) was proposed to overcome these challenges. SiC ceramic powder was pre-oxidized into SiC@SiO2 core-shell form to lower the UV-light absorbance. It was found that the ultraviolet (UV) light absorbance value of SiC powder at 405 nm decreased 20% from 0.357 to 0.284 after pre-oxidation process. The UV-light penetration depth of SiC@SiO2 ceramic slurries at 40 similar to 55 vol% solid loading ranging from 14.81 to 12.82 mu m, which surpassed two times that for 40 vol% raw SiC ceramic slurry. Different-shaped structures of SiC@SiO2/resin green ceramic bodies were successfully fabricated by vat photopolymerization 3D printing. The oxygen element resided was then eliminated by carbothermal reduction to avoid detriment of SiO2 to the mechanical performance of the SiC ceramics. Phenolic epoxy acrylate resin with 14 wt% pyrolytic carbon (PyC) yield was chosen as the carbon source and thus the SiC@SiO2/resin green body pyrolyzed into SiC@SiO2/PyC ceramics after 1200 degrees C. It was found that after the heating temperature was further raised to 1600 degrees C, most of the pre-introduced SiO2 shells on the surface of SiC particles were in situ transformed into SiC nanowires through carbothermal reduction reaction between SiO2 and PyC, and the content of oxygen element in the ceramic matrix sharply dropped from 20.21% to 2.08%. The results demonstrated that through the proposed redox route, the photopolymerization-related issues including high UV-light absorbance and pre-oxidation-induced impurity for 3D printing of SiC ceramic slurries can be tackled. Finally, high purity porous SiCnw/SiC ceramic components with different structures were produced. This study provides a promising route for the preparation and 3D printing of photopolymerization ceramic slurries using non-oxide ceramics possessing high UV-light absorbance.

Rheology and Curability Characterization of Photosensitive Slurries for 3D Printing of Si3N4 Ceramics

Effects of Stereolithography Process Parameters on the Curing Properties of Si3N4 Ceramic Slurries

Preparation of silicon carbide ceramic slurry for stereolithography based additive manufacturing

Dispersion and Stability of SiC Ceramic Slurry for Stereolithography

The Preparation of SiC Ceramic Photosensitive Slurry for Rapid Stereolithography

Rheological behavior and curing deformation of paste containing 85 wt% Al2O3 ceramic during SLA-3D printing

Optimization of Curing Behavior of Si3N4 UV Resin for Photopolymerization 3D Printing

Formation mechanism of stereolithography of Si3N4 slurry using silane coupling agent as modifier and dispersant

Preparation and optimization of silicon nitride slurries for digital light processing

Preparation of photosensitive SiO2/SiC ceramic slurry with high solid content for stereolithography

Preparation of High-Stability Ceramic Slurry with Gel Behavior for Stereolithography 3D Printing

Preparation of high solid loading and low viscosity ceramic slurries for photopolymerization-based 3D printing

Effects of Particle Size and Color on Photocuring Performance of Si3N4 Ceramic Slurry by Stereolithography

Si 3 N 4 slurry with high solid phase, low viscosity prepared via surface-oxidation and silane coupling agent modification hybrid method

Effect of TMAH as a modifier on the performance of Si3N4 stereolithography pastes

3D Printing and in Situ Transformation of SiCnw/SiC Structures

Rheological Behavior of SiO2 Ceramic Slurry in Stereolithography and Its Prediction Model Based on POA-DELM

A Comprehensive Study on Zirconia Slurry for Stereolithography-Based Additive Manufacturing

Effect of Solid Loading on the Property of Al2O3 Ceramics in Stereolithographic Additive Manufacturing

Effects of Ceramic Powder Coating Treatment on the Curing Behavior, Mechanical Properties, and Microstructure of 3D Printed Silicon Nitride Ceramics

Stereolithographical Fabrication of Dense Si3N4 Ceramics by Slurry Optimization and Pressure Sintering