Abstract:This paper presents an experimental investigation of the sample thickness effect on the concurrent flame steady spread behavior. Two configurations, ceiling flame and floor flame, as the fundamental diffusion combustion problems and representative scenarios of horizontal flame spread, are concerned herein. PMMA samples with thickness (delta) of 2, 3, 4, 5, 7, 9 mm were employed including both thermally-thin and thermally-thick conditions. A wind tunnel was used to provide the uniform concurrent airflow ranging from 0.3 m/s to 1.2 m/s in 0.3 m/s intervals. Flame characteristics and basic parameters to quantify the flame steady spread process have been studied, including flame spread rate (FSR), equivalent pyrolysis length as well as heat flux feedback in both pyrolysis and preheating zones. Results show that FSR decreases with sample thickness, being more sensitive to sample thickness for ceiling flame configuration than that for floor flame configuration. Equivalent pyrolysis length increases with sample thickness and ceiling flame's equivalent pyrolysis length is larger than floor flame's. Convection feedback is dominant under concurrent airflow regardless of the flame configuration, airflow velocity or sample thickness. In pyrolysis zone, the total heat flux to fuel surface of ceiling flame configuration is larger than that of floor flame configuration for thin samples due to buoyancy, but it decreases rapidly as sample thickness increases. In preheating zone, the heat flux decreases in power law for ceiling flame configuration while a piece-wise fitting is found for floor flame configuration, which is interpreted based on their inherent flame characteristic difference hence the thermal boundary layer conditions between these two configurations. To analyze the sample thickness effect on concurrent flame spread, a characteristic solid temperature (T*) is proposed by theoretical analysis, as an essential parameter to be used in the concurrent flame spread model to represent the coupling effect of heat input in gas phase and in-depth heat loss into the solid phase (or namely thermal inertia controlled by a characteristic thermal penetration depth). The calculated non-dimensional characteristic solid temperature (theta) shows to be less sensitive to flame configuration and concurrent airflow velocity for relatively thicker samples because the thermal penetration depth will tend to approach a limit. A general trend of its variation with sample thickness (delta) can be employed to predict the heat loss into solid phase and its predictive capability is verified by the experimental results. This work advances the fundamental understanding of the sample thickness effect on concurrent flame spread mechanism. (C) 2021 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Effectsof Equivalent Diameter on Verticalpmmacombustion in Natural Convection Environment

Heat Transfer Blockage Effect of Small-Scale PMMA Flame under Exterior Heat Radiation

Experimental Study on Coupled Combustion of PMMA Counter-directional Flame Spread in the Horizontal Direction

Experimental and numerical study of PMMA combustion in counterflow configuration

Effects of Overlap Length on Flammability and Fire Hazard of Vertical Polymethyl Methacrylate (PMMA) Plate Array

Experimental Study on Radiation Blockage of Small-Scale Vertical PMMA Fires

Effect of unheated length on heat transfer in a vertically solid burning

Effect of Forced Convection on the Combustion Chemistry of PMMA Spheres in Microgravity

Effect of Sample Thickness on Concurrent Steady Spread Behavior of Floor- and Ceiling Flames

Exploring the Combustion Mechanism of Single Micron-Sized Aluminum Particles with a Numerical Model

Experimental Study of Upward Flame Spread Behaviors over Thermally Thick Vertical PMMA of Various Sample Widths under Normal Wind

Heat flux and flame spread rate of discrete PMMA in concave building facade with window intervals

Heat and Mass Transfer and Chemical Kinetics in the Combustion of Polymethyl Methacrylate in Air under Free Convection

Study on the influence of restricted distance on fixed-width discrete of discontinuous flame spread

A Mixture Fraction Approach to Predict Polymer Burning

Thermodynamic and Kinetic Characteristics of Combustion of Discrete Polymethyl Methacrylate Plates with Different Spacings in Concave Building Facades

Effects of Combined Surface and In-Depth Absorption on Ignition of PMMA.

Experimental Study on Heat Transfer Blockage in Small Scale Flames

Experimental Study on Mass Burning Rate and Heat Feedback Mechanism of Pair of Unequal Circular Pool Fires of Heptane

Effect of solid surface curvature and wall heat loss on the downward flame spread along the edge of thin PMMA sheets

Effects of the PMMA Molecular Weight on the Thermal and Thermo-Oxidative Decomposition as the First Chemical Stage of Flaming Ignition