Abstract:Amorphous alumina films are isotropic and have no grain boundaries, which make them have smooth surfaces, excellent properties, and wide applications in protective coatings, catalysis, and microelectronics. However, high-quality alumina films were usually prepared by vapor-phase approaches which need expensive equipment and long production time. Additionally, amorphous films are long-range disordered, which makes the study of structure–property relationships challenging. Here, a simple sol–gel method is employed to obtain high-quality amorphous Al2O3 thin films. The microstructure, morphology, and mechanical properties of amorphous Al2O3 thin films were systematically investigated. All the Al2O3 thin films heat-treated at 600–800∘C are in amorphous state with ultrasmooth surface (Ra values about 0.29–0.43 nm) and high mechanical properties (elastic modulus ∼170[Formula: see text]GPa, hardness ∼20[Formula: see text]GPa). The mechanical properties (E and H) of Al2O3 films gradually increase with the increase of heat-treating temperature. Additionally, the Al coordination of the amorphous alumina films are analyzed by solid-state NMR and correlated with the mechanical properties. The results show that in amorphous alumina, the presence of tetrahedral Al ([4]Al) and octahedral Al ([6]Al) is helpful to improve the mechanical properties, while the five-coordinated Al ([5]Al) is not conducive to improve the mechanical properties. The results demonstrate that sol–gel method is an attractive alternative to time-consuming and expensive vapor-phase approaches and are useful for scale-up to applications and research of amorphous alumina films.

Structure and Electronic Properties Calculation of Ultrathin Α-Al2o3 Films on (0001) Α-Cr2o3 Templates

Ab Initio Calculation of Structure and Thermodynamic Properties of Zintl Aluminide SrAl2

The Microstructure, Morphology, and Mechanical Properties of Sol-Gel-derived Amorphous Aluminum Oxide Films

Atomic layer deposition of chromium oxide—An interplay between deposition and etching

Structure and refractive index of thin alumina films grown by atomic layer deposition

Preparation and Characterization of Α-Al2o3 Film by Low Temperature Thermal Oxidation of Al8Cr5 Coating

Shrunk Lattice Structure and Interdiffusion Characteristics of 5 Nm Thick Al(2)O(3) Ultrathin Films Sputtered on Silicon.

Preparation Of Alpha-Al2o3 Thin Films By Electron Cyclotron Resonance Plasma-Assisted Pulsed Laser Deposition And Heat Annealing

Molecular Dynamics Study of Substrate Temperature and Incident Energy Influence on the Crystallization Behavior of Alumina Thin Film Deposition Process

Ab initio structure modeling of complex thin-film oxides: thermodynamical stability of TiC/thin-film alumina

First-Principles Calculated Structures and Carbon Binding Energies of Σ11 {101̅1}/ . -0pt{101̅1̅} Tilt Grain Boundaries in Corundum Structured Metal Oxides

Preparation of α- Al2 O3 thin films by electron cyclotron resonance plasma-assisted pulsed laser deposition and heat annealing

First-principles calculations of (0 0 1)α-Al//(0 0 1)θ' interface in Al-Cu alloys: Atomic structure, bonding strength, stability and electronic properties

Stoichiometric reconstruction of the Al2O3(0001) surface

First-principles calculations of γ-Al2O3/Al interfaces

Large interlayer relaxation at a metal-oxide interface: the case of a supported ultrathin alumina film

The Effect of Chromium on the Gamma to Alpha Phase Transition of Alumina Coating Formed on 316L SS by a Cathodic Micro Arc Deposition (CMAD) Process

Mechanical and Optical Properties of Cr2O3 Thin Films Grown by Atomic Layer Deposition Method Using Cr(thd)3 and Ozone

Electronic Structure, Bonding, and Mechanical Strength at the Α-Al 2 O 3 (0001)/L12-Al3zr 2-Al 3 Zr (111) Interface by First-Principles Calculations

CHARACTERIZING CRYSTALLINE CHROMIUM OXIDE THIN FILM GROWTH PARAMETERS

First-principles study of the Ti(0001)/TiAl 3 (110) interfacial properties