Abstract:As well known, sustainability issues represented by the environment and resource protection have been paid close attention nowadays. Natural fiber has been an increasing interest and promising as reinforcing fiber in polymeric composites due to its low density, cost, acceptable specific strength and biodegradation. Even though, the principle challenge for natural fibers used as reinforcement is their internal strong water-absorption ability when the exposed in wet and water environment. Long-term hydrothermal degradation behavior of Glass reinforced composite (GFRP) and jute reinforced composite (JFRP) have been discussed in previous study on the basis of the great amount of physical and mechanical testing results. As former working reported, gained water content increases linearly against the square root of aging time followed by gradual increase trend in longer duration both in JFRP and GFRP. In particularly, JFRP’s weight loss performance occurred earlier with higher value compared to GFRP. However, water absorption and weight loss mechanism, relationship between weight change and retention of mechanical property for JFRP didn’t report and illustrate clearly and extensively. Therefore, in order to figure it out comprehensively, the current study was focus on hydrothermal ageing mechanism and corresponding degraded mechanical behavior. Firstly, 2 layers of deeply dried and natural dried jute woven fabric reinforced unsaturated polyester were fabricated by hand-layup method. The cut samples were immersed into 80°C hot water bath for predetermined durations and inspected by ultrasonic wave. Afterwards, 3-point bending test with acoustic emission (AE) measurement was carried out for aged samples. The weight change mechanism, evolution of internal deterioration and mechanical property along with ageing time was investigated. The result indicated that JFRP can absorb water easily and quickly compared with GFRP owing to jute fiber’s hydroscopic nature. Weight loss was caused as a result of resin particle loss and pectin dissolution from the developed micro-crack owing to hydrothermal water environment. What’s more, internal serious deterioration occurred after 24 hours immersion leading to larger reduction of mechanical property.

Effect of Saline and Alkaline Solution Aging on the Properties of Jute/poly(lactic Acid) Composites

Effect of Low‐concentration Alkali Solution Pretreatment on the Properties of Bamboo Particles Reinforced Poly(lactic Acid) Composites

Effects of Hygrothermal Aging and Cyclic Compressive Loading on the Mechanical and Electrical Properties of Conductive Composites

Enthalpy Relaxation And Embrittlement Of Poly(L-Lactide) During Physical Aging

Effect of short jute fibers on the hydrolytic degradation behavior of poly(lactic acid)

Research on the Aging Effects of Adhesive and Composites on the Degradation Mechanism of Composite Adhesive Joints in Thermal-Humidity-Cycles for Automobiles

Influence of water absorption track and pre‐drying treatment on the long‐term hydrothermal aging behavior of recycled jute fabric‐reinforced composites

Experimental Investigation on Fabrication and Thermal-Stamping of Woven Jute/polylactic Acid Biocomposites

Insight to the influence of alkali treatment on mechanical and tribological properties of a novel carbon/jute hybrid porcine filled polyester composite

Hydrothermal Ageing Mechanism of Natural Fiber Reinforced Composite in Hot Water

Poly(lactic acid)/pulp fiber composites: The effect of fiber surface modification and hydrothermal aging on viscoelastic and strength properties

Environmental Degradation of Starch/Poly(Lactic Acid) Composite in Seawater

Degradation of Mechanical Properties of Flax/PLA Composites in Hygrothermal Aging Conditions

Effects of annealing on the mechanical, thermal, and physical properties of 3D-printed PLA aged in salt water

Reversible and irreversible changes in physical and mechanical properties of biocomposites during hydrothermal aging

Sustainable jute fiber reinforced polylactic acid composite: Thermochemical and thermomechanical characteristics

Influence of structural design on mechanical and thermal properties of jute reinforced polylactic acid (PLA) laminated composites

Influence of fiber volume fraction and curing temperature on mechanical properties of jute/PLA green composites

Effect of steam explosion and silanization of hemp fibers on polylactic acid biocomposites; analysis of mechanical-thermal properties and fungal biodegradation

Aging effect on surface chemistry and sorption properties of atmospheric pressure plasma treated lignocellulosic jute fibers

Impact of In-Soil Ageing Effect on PLA Printed Parts Tensile Properties