Abstract:Abstract. Radioactive waste in Switzerland will be disposed of in a deep geological repository (DGR). Responsible for the planning and preparation of realization of this task is National Cooperative for the Disposal of Radioactive Waste (Nagra). Spent fuel assemblies (SFA) constitute the main high-level waste (HLW) stream that will be disposed in the DGR. Prior to final disposal they will be transferred or transported to an encapsulation plant, where they will be loaded into final disposal canisters. To ensure that the structural integrity of SFAs is not compromised during handling and transportation, it is desirable to characterize the expected mechanical parameters of SFAs after long-term interim storage. Experimental research activities performed at the JRC Karlsruhe include safety aspects of radioactive waste management, encompassing also spent fuel storage and spent fuel/HLW disposal activities. Nagra and JRC have established a collaboration to jointly study relevant properties and behaviours of spent fuel rods, with the support of the Gösgen nuclear power plant and of Framatome, and in collaboration with other partners in Europe and internationally. As part of this collaboration, 3-point bending and impact tests were performed at the hot-cell facilities of JRC Karlsruhe, to determine the mechanical response of spent fuel rodlets under quasi-static and dynamic loads. The structural integrity of fuel rods was also evaluated under different handling scenarios using finite element (FE) analysis. Starting with the construction of a static 3D FE model of a Pressurized Water Reactor (PWR) nuclear fuel rodlet in ANSYS Mechanical, Nagra has developed a series of FE models over the years. Mechanical properties of the original rodlet model were derived through an extensive validation process, using experimental data from the 3-point bending tests. To evaluate the mechanical response of an SFA in different loading scenarios, this model was expanded using 1D beam modeling approach. The development of the simplified 1D models is shown in this presentation. In particular, the effect of the contact formulation between the spacer grid and the rods is discussed. Finally, preliminary results of the bending response of a 15×15 PWR SFA sub-model are presented.

Development of U-frame Bending System for Studying the Vibration Integrity of Spent Nuclear Fuel

A modified small punch testing scheme to investigate the circumferential mechanical behavior of nuclear fuel cladding tubes

Creep-fatigue Properties and Deformation Mechanism of 316L Steel Fabricated by Laser Powder Bed Fusion (PBF-LB/M)

Numerical Simulation Investigations on the Flow Induced Vibration of a Nuclear Fuel Rod with Relaxed Clamping Structures

A Novel Model of Ultrasonic Fatigue Test in Pure Bending

A Novel Ultrasonic Fatigue Test and Application in Bending Fatigue of TC4 Titanium Alloy

An Approach to Estimate the Low Cycle Fatigue Probabilistic Curves of PBF-LB/M 316L Steel from Small Size Datasets Using the Remora Optimization Algorithm

Structural integrity investigations of spent nuclear fuel with finite element modeling

A Particle Finite Element Method Based Partitioned Paradigm for the Axial-Flow-induced Vibration Analysis of NHR200-II Fuel Rod

Application of URANS Simulation and Experimental Validation of Axial Flow-Induced Vibrations on a Blunt-End Cantilever Rod for Nuclear Applications

Study of Fatigue Properties of Graphite Materials under Four-Point Bending

Direct Observation of Fatigue Cracking in the Fuel Plate Using the Scanning Electron Microscope

The high-throughput bridge to the rapid evaluation of fatigue reliability of structural engineering materials

Study on the Structural Evaluation and Optimization of Spent Nuclear Fuel Cask

Experimental Research on Assembly Section Stiffness and Bending Stiffness for Sodium-Cooled Fast Reactor

Analysis of Flow-Induced Vibration of Wire-Wrapped Fuel Assemblies under the Liquid Metal Axial Flow in the Gen-IV Nuclear Reactor

Development and Application of High-Accuracy Metal Fuel Performance Analysis Code Based on Fem Method

Development of In Situ Fatigue Performance Testing Apparatus for Materials Under Coupling Conditions of High-Temperature and Combined Mechanical Loads

A study of ultra-low cycle fatigue failure based on a fracture strain energy model

Fatigue tests of multiplanar concrete-filled steel tubular KK-joints with inner ring stiffeners

Seismic responses of a fuel assembly in nuclear heating reactor