Abstract:The tribological behaviour of Fe–28Al–5Cr and its composites containing 15, 25 and 50 wt% TiC (corresponding to 19.3, 31.2 and 57.6 vol%), produced by hot-pressing process, was investigated under liquid paraffine lubrication against an AISI 52100 steel ball in ambient environment at varied applied loads and sliding speeds. It was found that the wear resistance increased and friction coefficient decreased with increasing of TiC content. The coefficients of friction are in the range of 0.09–0.14 at the given testing conditions. The wear rates of all the materials except the 50% composite are on the order of 10−6–10−5 mm3 m−1, the wear rate for the 50% composite is too low to quantify under the two sliding conditions, (50 N, 0.04 m/s) and (100 N, 0.02 m/s). The wear rates of all the materials increase as applied load increases and the increasing extent diminishes with the increase of TiC content, but first increase slightly and then nearly remains steadiness with increasing sliding speed. The 50 wt% composite has wear resistance about 7–20 times better than pure Fe–28Al–5Cr at different sliding parameters. The enhanced wear resistance by TiC addition is attributed to the high hardness of the composites, as well as support of the oil lubrication film/layer by the hard TiC phase. The worn surfaces of all the materials are analyzed by a scanning electron microscope. The dominant wear mechanism of the Fe–28Al–5Cr and 15% composite is grooving and flaking-off, but those of the 25 and 50% composites are mainly shallow grooving.

Evaluation on tribological characteristics of (TiC+TiB)/Ti-6Al-4V composite in the range from 25 C to 600 C

Effect of Temperature on Tribological Properties of Cu/Ti3AlC2 Composites

Investigation on Tribological Behavior of Ti2AlN/TiAl Composite at Room and Elevated Temperature

Tribological Behavior of In-Situ (cr, Mo)/Fe3al-20 Wt.%Al2o3 Composites at Elevated Temperatures

Insights into Wear Behavior of (tic + TiB)/TC4 Composites Against Different Counterface Materials

The Tribological Behaviour of Fe–28Al–5Cr/TiC under Liquid Paraffine Lubrication

Microstructure and tribological behaviors of laser cladded CuAlMnTi–xTiC composite coatings at elevated temperature

Wear Rate of Titanium Matrix Composite Coating at High Temperature Further Increased by Non-Stoichiometric TixC Oxidation

Investigation on Microstructures and Mechanical Behavior of In-Situ Synthesized TiC and TiB Reinforced Ti6Al4V Based Composite

High-Temperature Tribological Performance of Ti 3 SiC 2 /tial Self-Lubricating Composite Against Si 3 N 4 in Air

High Temperature Tribological Behavior of a Ti-46Al-2Cr-2Nb Intermetallics

The tribological behavior evolution of TiB2/Al composites from running-in stage to steady stage

Dry-Sliding Tribological Properties of TiAl Alloys and Ti 2 AlN/TiAl Composites at High Temperature

Tribological Performance Of Tial Matrix Self-Lubricating Composites Containing Ag, Ti3sic2 And Baf2/Caf2 Tested From Room Temperature To 600 Degrees C

High temperature and room temperature tribological behaviors of in-situ carbides reinforced Ni-based composites by reactive sintering Ni and Ti2AlC precursor

Response of tribological behaviors to microstructural characteristics of Ti-40Al-10V alloy at high temperatures

Investigation on the Elevated-Temperature Tribological Behaviors and Mechanism of Al-Cu-Mg Composites Reinforced by In-Situ Size-Tunable TiB2-TiC Particles

Wear Behavior of Ti6Al4V Based Hybrid Composites Reinforced with TiB2(7.5%) + TiC (7.5%)

Tribological Behaviors of NiAl-Ti3SiC2Self-Lubricating Composites at Elevated Temperatures

Effect of Temperature on Tribological Properties of Tial Based Self-Lubricating Composites

Wear Behavior of TiN/TiAlSiN Nanocomposite Multilayer Coatings from Ambient Temperature to Medium Temperature