Abstract:The unsatisfactory high-temperature performance of commonly used silicon carbide (SiC)-based ceramics calls for a novel approach for their reinforcement. We present the in situ preparation of a SiC-based composite with uniformly dispersed titanium boride (TiB2) particles using titanium carbide and boron carbide as raw materials. Notably, the uniform incorporation of 25 wt%TiB2 results in the SiC–TiB2 composite with excellent tribological and self-lubricating properties at high temperatures. The SiC–TiB2 composite shows a friction coefficient of 0.20 and a specific wear rate of 5.77 × 108 mm3/(N mm), which are 4.75 times and ~ 5.2 times lower than that of the bare SiC ceramic at 1000 °C, respectively. The wear mechanism of a self-mated couple of the SiC–TiB2 composite is unraveled to be the tribo-oxidization. Since intimate contact exists between the oxidizing layer and the transitional layer of the fractured surface, the friction surface possessing plastic deformation properties may transit from brittle to plastic or elastic. The "Pin Effect" exhibited by TiB2 particles in the SiC–TiB2 composite deflects the crack propagation route. Meanwhile, a change in stress distribution, a decrease in the stress intensity of slight crack frontier, and an increase in "the threshold value" of crack propagation occur. The type (I + II) and type (I + III) complex cracks in fracture mechanics propagate non-flatly in the wearing process of the self-mated couple of the SiC–TiB2 composite. Besides, a fine yield deformation zone exists on the crack tip. Consequently, the "threshold value" of crack propagation fluctuates dynamically between "upper bound value" and "lower bound value" following the change in the valid length of actual crack propagation, thus delaying the fracture of the SiC–TiB2 composite.

Interface Characteristics and High Temperature Wear Properties of Refractory Steel Matrix Composite Reinforced by Zoning CTCP/NiCrBSi

Interfacial characteristics and elevated temperature wear behavior of WCp-NiCrBSi/refractory steel composite

Effect of Surface-Modified WC/W2CP on Wear Behavior of WC/W2CP-NiCrBSi/Refractory Steel Composite

Interface and wear characteristics of high-Cr cast iron matrix composite reinforced with cemented carbide particles

High Temperature Sliding Wear Behaviors of Ion Plating Tin Composite Coating with Ion Nitriding As Interlayer on Hot Work Die Steel

Enhancing High-Temperature Wear Resistance by Constructing the Amorphous-Crystal Heterointerface Structure in WO3/TiO2 Composite Coatings

Interfacial Bonding And Abrasive Wear Behavior Of Iron Matrix Composite Reinforced By Ceramic Particles

Interface Structure and Wear Behavior of Cr26 Ferrous Matrix Surface Composites Reinforced with CTC P

Microstructure and Wear Behavior of High-Cr WCI Matrix Surface Composite Reinforced with Cemented Carbide Rods

Interfacial Characteristics of WC Particles Reinforced Hadfield Steel Matrix Composites

Evaluation on tribological characteristics of (TiC+TiB)/Ti-6Al-4V composite in the range from 25 C to 600 C

FABRICATION OF Al2O3/HEAT-RESISTANT STEEL COMPOSITEAND ITS WEAR-RESISTANCE AT HIGH TEMPERATURE AND ABRASIVE

Study on the friction and wear properties of nickel-based-WC-10Ni composite coatings prepared on the surface of TC4 titanium alloy

Fabrication of TiC Particles Reinforced Hadfield Steel Matrix Composite and Its Wear-Resistance

Wear Rate of Titanium Matrix Composite Coating at High Temperature Further Increased by Non-Stoichiometric TixC Oxidation

Dry Sliding Friction And Wear Mechanism Of Tic-Tib2 Particulate Locally Reinforced Mn-Steel Matrix Composite From A Cu-Ti-B4c System Via A Self-Propagating High-Temperature Synthesis (Shs) Casting Route

Interfacial characteristics and wear performances of iron matrix composites reinforced with zirconia-toughened alumina ceramic particles

Interface Property and Two-Body Wear Behavior of High-Cr Wci Matrix Composite Reinforced with Cc Particles

In situ preparation of a SiC–TiB2 composite and its wear fracture mechanism at high temperatures

Preparation and Mechanical Property of the Ceramic-reinforced Cr0.5MoNbWTi Refractory High-entropy Alloy Matrix Composites