Highly Efficient Conversion of Biomass-Derived Levulinic Acid into Γ-Valerolactone over Ni/MgO Catalyst

jinkun lv,zeming rong,jinghai xiu,yue wang,jingping qu

DOI: https://doi.org/10.1039/c5ra12548k

IF: 4.036

2015-01-01

RSC Advances

Abstract:Hydrogenation of levulinic acid (LA) was investigated with Ni/MgO for the production of γ-valerolactone (GVL).

What problem does this paper attempt to address?

Highly efficient Ni-Mn/SiO<sub>2</sub> catalyst for the selective hydrogenation of biomass-derived levulinic acid to -valerolactone under mild conditions

Mengting Chen,Qifeng Zhong,Jiao Ma,Zhiyang Zhang,Yingxin Liu,Zuojun Wei,Shuguang Deng

DOI: https://doi.org/10.1039/d3nj01010d

IF: 3.3

2023-01-01

New Journal of Chemistry

Abstract:Hydrogenation of levulinic acid (LA) to gamma-valerolactone (GVL) is a key reaction in the conversion of biomass to renewable fuels and value-added chemicals. Developing low-cost, highly efficient and reusable non-noble metal-based heterogeneous catalysts is vital but challenging. Herein, non-noble Ni-Mn/SiO2 catalysts with a low Ni loading (2.0 wt%) were designed for the selective hydrogenation of LA to GVL. The results showed that the optimal Ni-Mn/SiO2 (Ni/Mn = 2) catalyst with well-dispersed and small-sized metal nanoparticles (2.21 nm) and moderate acid sites exhibited excellent activity and selectivity and achieved a 100% yield of GVL in a 1,4-dioxane solvent under mild reaction conditions (e.g., 0.8 mol% Ni, 140 degrees C and 2.0 MPa H-2) for 5.5 h and a 100% GVL yield at 180 degrees C for 2 h with a turnover frequency (TOF) of 190.2 h(-1), which is better than most non-noble metal catalysts reported. Furthermore, the catalyst exhibited excellent reusability and could be recycled at least five times with only slight activity loss. This work provides new insights for the rational design of highly efficient and stable non-noble metal catalysts for the conversion of LA to GVL.
Hydrogenation of Levulinic Acid over Nickel Catalysts Supported on Aluminum Oxide to Prepare Γ-Valerolactone

Jie Fu,Dong Sheng,Xiuyang Lu

DOI: https://doi.org/10.3390/catal6010006

IF: 3.9

2016-01-01

Catalysts

Abstract:Four types of nickel catalysts supported on aluminum oxide (Ni/Al2O3) with different nickel loadings were synthesized using the co-precipitation method and were used for the hydrogenation of levulinic acid (LA) to prepare γ-valerolactone (GVL). The synthesized Ni/Al2O3 catalysts exhibited excellent catalytic activity in dioxane, and the activity of the catalysts was excellent even after being used four times in dioxane. The catalytic activity in dioxane as a solvent was found to be superior to the activity in water. Nitrogen physisorption, X-ray diffraction, and transmission electron microscopy were employed to characterize the fresh and used catalysts. The effects of the nickel loading, temperature, hydrogen pressure, and substrate/catalyst ratio on the catalytic activity were investigated.
Highly Efficient Selective Hydrogenation of Levulinic Acid to Γ-Valerolactone over Cu–Re/TiO2 Bimetallic Catalysts

Yingxin Liu,Kai Liu,Meihua Zhang,Kaiyue Zhang,Jiao Ma,Shuwen Xiao,Zuojun Wei,Shuguang Deng

DOI: https://doi.org/10.1039/d1ra05804e

IF: 4.036

2022-01-01

RSC Advances

Abstract:Herein, we report a highly efficient and recyclable Cu–Re(1 : 1)/TiO2 bimetallic catalyst for liquid phase hydrogenation of levulinic acid to γ-valerolactone.
Catalytic Hydrogenation of Levulinic Acid to Gamma-Valerolactone over Ni/ZrO2

Dong Sheng,Jie Fu,Xiuyang Lv

2016-01-01

Abstract:Five kinds of nickel supported zirconia (Ni/ZrO2) catalysts were prepared and characterized by N2 physisorption, X-Ray diffraction and transmission electron microscope(TEM) analysis. The effects of nickel loading and different reaction conditons on the catalytic activity were studied. The results showed that the conversion of levulinic acid increased with the increase of nickel content. It was found that the highest conversion could be achieved over 50 % Ni/ZrO2 and the highest turnover frequency(TOF) was obtained over 30% Ni/ZrO2. The reaction was accelerated with the increase of reaction temperature and much favored in dioxane than in water. The highest conversion of levulinic acid (99.1%) and yield of gamma-valerolactone (91.6%) were achieved after 9 hours under the conditions of 200℃ and hydrogen pressure of 5 MPa in dioxane.
Selective Production of gamma-Valerolactone and Valeric Acid in One-Pot Bifunctional Metal Catalysts

Anqi Wang,Yiran Lu,Zixiao Yi,Ashan Ejaz,Kang Hu,Lin Zhang,Kai Yan

DOI: https://doi.org/10.1002/slct.201702899

2018-01-01

ChemistrySelect

Abstract:In this work, one-pot synthesis of biofuel-valerolactone (GVL) and valeric acid (VA) from biomass-derived levulinic acid (LA) are highly selectively produced on a series of robust Pd-nanoparticle catalysts. These fine Pd nanoparticles are controllably synthesized and confined in the mesoporous channel of MCM-41-derived supports via a green solvent CO2-assited method. A combination analysis tools are used to study physical properties and elucidate the relationship between the structure and performances. The catalytic results display 5 wt% Pd/AlMCM-41 exhibits the best performances of 88.5% GVL yield at the perfect conversion of LA. Moreover, without the isolation of GVL intermediate, it can also efficiently catalyze the one-pot conversion of LA to VA with 45.1% yield. Besides, Pd-nanoparticle catalysts maintain stable structure and good catalytic performances over several runs.
Selective Production of γ-Valerolactone from Biomass-Derived Levulinic acid over Ni/CMK-3 catalyst

Rui Zhang,Xishang Song,Han Wu,Yunqi Zhai,Yina Qiao,Zhihao Yu,Jian Xiong,Xuebin Lu

DOI: https://doi.org/10.1039/d3nj04771g

IF: 3.3

2023-12-25

New Journal of Chemistry

Abstract:The conversion of levulinic acid (LA) into γ-valerolactone (GVL) is a critical reaction for upgrading biomass into high value-added chemicals. The catalyst's stability and activity are strongly correlated with its performance. Based on this, a series of Ni/CMK-3 catalysts with defective mesoporous carbon and nickel-anchored loading were synthesized. The analysis found that the Ni particles were securely implanted in the flawed areas of the C groups on the pores' wall. This ensures that the active sites remain stable. The catalytic reaction yielded 79.82% GVL with 81.91% selectivity under optimal conditions, matching previously reported catalytic performances. The catalyst demonstrated a 97.30% conversion rate of LA and a yield of 79.49% GVL after five consecutive experiments. In conclusion, the catalyst Ni/CMK-3developed in this study exhibits strong stability, excellent structure, and efficient catalytic performance. These properties make it an ideal choice for converting LA into GVL.

chemistry, multidisciplinary
Selective Conversion of Levulinic Acid to Gamma-Valerolactone over Ni-based Catalysts: Impacts of Catalyst Formulation on Sintering of Nickel

Yuewen Shao,Kai Sun,Mengjiao Fan,Junzhe Wang,Guoming Gao,Lijun Zhang,Shu Zhang,Xun Hu

DOI: https://doi.org/10.1016/j.ces.2021.117258

IF: 4.7

2022-01-01

Chemical Engineering Science

Abstract:Selective production of γ-valerolactone (GVL) from hydrogenation of levulinic acid (LA) is challenging over non-noble metal catalysts but attractive due to the promising application of GVL as platform chemical. In this study, Ni catalysts supported on Mg-Al and Ni-Al layered double hydroxides (LDH) were synthesized for hydrogenation of LA. LDH as the precursor could create developed porous structure and facilitate dispersion of Ni species. These factors together achieved selective conversion of LA to GVL with maximum yield of 99% over the 2.25Ni-0.75Mg-Al catalyst. The Ni-based catalysts are not active for the ring-opening of GVL. Mg and Al together in 2.25Ni-0.75Mg-Al suppressed the sintering of nickel species in ethanol, achieving much superior reusability to Ni-Mg. However, in water, the transformation of MgO in either Ni-Mg or 2.25Ni-0.75Mg-Al to amorphous Mg(OH)2 led to the collapse of pore structure and remarkable deactivation of the catalysts, while Ni-Al without Mg species performed much better.
Efficient Hydrogenation of Biomass-derived Levulinic Acid into γ-Valerolactone Under Mild Condition

DU Xian-long,YUAN Jing,CAO Yong,LIU Yong-mei,FAN Kang-nian

DOI: https://doi.org/10.15943/j.cnki.fdxb-jns.2012.05.011

2012-01-01

Abstract:Ir/CNT,a catalyst of high-activity,was used for the hydrogenation of levulinic acid(LA) to y-valerolactone(GVL),and all the factors that affect LA hydrogenation were discussed.The variations of the fresh and used catalysts were characterized by XRD、TEM and XPS.The origin for high activity of Ir/CNT catalyst was investigated through H_2-TPD experiment.It was found that an excellent GVL yield of 99%has been obtained at 50℃and 2 MPa H_2.Finally the simulated biomass-derived substrates containing equimolar amounts of LA and formic acid can be converted into GVL in the presence of Ir/CNT catalyst with enhanced hydrogen pressure.
Catalytic Conversion of Biomass-Derived Levulinic Acid into Γ-Valerolactone Using Iridium Nanoparticles Supported on Carbon Nanotubes

Du Xianlong,Liu Yongmei,Wang Jianqiang,Cao Yong,Fan Kangnian

DOI: https://doi.org/10.1016/s1872-2067(11)60522-6

2013-01-01

Abstract:A new method has been developed for the catalytic conversion of biomass-derived levulinic acid (LA) into gamma-valerolactone (GVL) with molecular hydrogen (H-2) using a series of heterogeneous noble metal catalysts. Excellent yields of the GVL were obtained under mild reaction conditions of 50 degrees C and 2 MPa of H-2 using iridium nanoparticles supported on carbon nanotubes (Ir/CNT). It is noteworthy that the reaction proceeded smoothly in the presence of formic acid (FA, co-produced with LA in equimolar amounts during the acid-mediated hydrolysis of lignocellulosic biomass). Furthermore, the FA remained intact, highlighting the practical advantages of this process for the convenient and cost-effective processing of a biomass-derived LA/FA solution. The method is effective for the simultaneous production of GVL and FA from a wide variety of renewable biomass resources. (C) 2013, Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by Elsevier B.V. All rights reserved.
Highly Efficient Hydrogenation of Levulinic Acid into Γ‐valerolactone Using an Iron Pincer Complex

Yuxuan Yi,Huiying Liu,Ling-Ping Xiao,Bo Wang,Guoyong Song

DOI: https://doi.org/10.1002/cssc.201800435

IF: 8.4

2018-01-01

ChemSusChem

Abstract:The search for nonprecious-metal-based catalysts for the synthesis of gamma-valerolactone (GVL) through hydrogenation of levulinic acid and its derivatives in an efficient fashion is of great interest and importance, as GVL is an important a sustainable liquid. We herein report a pincer iron complex that can efficiently catalyze the hydrogenation of levulinic acid and methyl levulinate into GVL, achieving a turnover number of up to 23000 and a turnover frequency of 1917 h(-1). This iron-based catalyst also enabled the formation of GVL from various biomass-derived carbohydrates in aqueous solution, thus paving a new way toward a renewable chemical industry.
Catalytic Hydrogenation of Levulinic Acid for the Preparation of γ-Valerolactone by CuAgZrO2-graphene Nanocomposite

Yufeng Jia,Hui Lv,Jingbo Mao,Jinxia Zhou

DOI: https://doi.org/10.1039/d3nj05088b

IF: 3.3

2024-03-27

New Journal of Chemistry

Abstract:Hydrogenation of biomass-derived levulinic acid (LA) could produce a high value-added compound, gamma-valerolactone (GVL). However, metal leaching is a major issue in the efficient production of GVL from LA due to the acidity of LA. Some endeavors have tended to focus on the external factors of the catalysts for preventing metal leaching, such as reaction at high temperature and H2 pressure or the esterification of LA with alcohols. Focusing on the catalyst itself, in this work, metal leaching was solved by the selection of suitable catalyst compositions and preparation methods. The CuAgZrGO catalyst was synthesized by regulating the pH of the precipitation system to achieve a one-pot layered assembly of Zr4+, Cu2+, and Ag+ components on the graphene oxide (GO) surface at the atomic level. The catalyst without reduction pretreatment resulted in the complete conversion of LA and achieved approximately 100% yield of GVL, and metal leaching in the LA aqueous phase could be substantially prevented. Under mild reaction conditions, the catalyst exhibits good stability after four times of recycling in the aqueous phase. The positive-titration co-precipitation method controls the Ag more scattered on the surface of Cu and Zr precipitate, which makes CuAgZrGO to be metal-leaching-resistant catalyst for aqueous-phase hydrogenation of LA.

chemistry, multidisciplinary
Synthesis of Γ-Valerolactone from Ethyl Levulinate Hydrogenation and Ethyl 4-Hydroxypentanoate Lactonization over Supported Cu-Ni Bimetallic, Bifunctional Catalysts

Yafei Li,Xiaocheng Lan,Boyang Liu,Tiefeng Wang

DOI: https://doi.org/10.1016/j.jiec.2021.11.048

IF: 6.76

2021-01-01

Journal of Industrial and Engineering Chemistry

Abstract:A stable and highly efficient supported Cu-Ni catalysts for the conversion of ethyl levulinate (EL) to gamma-valerolactone (GVL) was developed. The catalysts were characterized by XRD, TEM, TPD, TPR, and XPS. The support effect of metal oxides (Al2O3, SiO2, ZrO2, and TiO2) revealed that Cu-Ni supported on Al2O3 showed the highest activity for EL hydrogenation to ethyl 4-hydroxypentanoate (EHP) and the subsequent intramolecular esterification of EHP to GVL. EHP intramolecular esterification to GVL in the ethanol solution was a reversible reaction with an equilibrium constant of 24 at 453 K. A simplified reaction kinetic network was established. The solvent had a significant influence on the reaction equilibrium and the catalyst stability. Cu-Ni/Al2O3 in n-hexane solvent gave a higher GVL yield than that in ethanol solvent, and showed better recyclability than that in toluene solvent. With optimizing the conditions, CuNi/Al2O3 gave 99.9% conversion and 98% selectivity to GVL with a space-time yield of 1.13 gGVL gcat(-1) h(-1) in n-hexane solvent with good recyclability. (C) 2021 The Korean Society of Industrial and Engineering Chemistry. Published by Elsevier B.V. All rights reserved.
Conversion of Levulinate Ester and Formic Acid into Γ-Valerolactone Using a Homogeneous Iron Catalyst

Ming-Chen Fu,Rui Shang,Zheng Huang,Yao Fu

DOI: https://doi.org/10.1055/s-0034-1379462

2014-01-01

Synlett

Abstract:An iron-catalyzed hydrogenation of biomass-derived ethyl levulinate (EL) to -valerolactone (GVL) has been developed using formic acid as hydrogen source. Ethyl levulinate was converted into -valerolactone quantitatively under optimized reaction conditions. This catalytic process does not require the use of any base or additives.
Production of γ-Valerolactone from Methyl Levulinate via Catalytic Transfer Hydrogenation on Nickel-Copper Oxide Catalyst

Worapak Tanwongwal,Sanchai Kuboon,Wasawat Kraithong,Apiluck Eiad-Ua

DOI: https://doi.org/10.4028/www.scientific.net/msf.872.187

2016-09-01

Materials Science Forum

Abstract:γ-Valerolactone (GVL) is successfully produced via catalytic transfer hydrogenation from methyl levulinate on nickel copper oxide catalysts with the comparable result to that of Raney-nickel. This catalyst is prepared at lower temperature (lower than 1000oC) and pretreatment is not required before its use. Among different calcination temperature, Ni-Cu-O which synthesis at 700oC shows the best catalytic performance with 100% methyl levulinate conversion and more than 95% GVL yield and characterization result was shows this calcination temperature was affect catalyst to highest crystallization and surface area. The study of atomic ratio effect indicates that nickel-copper oxide which had nickel oxide more than copper oxide is better for this reaction.
Ion-Exchange Synthesis of Surrounded CoNi@Al2O3 Catalyst for Levulinic Acid Hydrogenation to γ-Valerolactone under Mild Conditions

Hongzhi Ding,Chenyu Yang,Congyan Jiang,Wei Luo,Qiuyue Wang,Xuefeng Guo

DOI: https://doi.org/10.3390/catal14020113

IF: 3.9

2024-01-31

Catalysts

Abstract:The use of eco-friendly biomass as a resource is an efficient way to address the problems of fossil fuel depletion and climate change. In biomass conversion, versatile γ-valerolactone (GVL) is generally obtained from levulinic acid (LA) hydrogenation via a multimetallic catalyst system. Despite conversion efficiency being enhanced in mild conditions due to metal interactions, maintaining high catalyst stability is still a challenge. In this study, we synthesized a surrounded Co0.52Ni0.48@Al2O3-IE catalyst that exhibited excellent alloying and synergistic interaction between the metal constituents. Under relatively mild reaction conditions, the GVL yield over the catalyst exceeded 99% in LA hydrogenation. The catalyst showed no deactivation in a test of five cycles, displaying superiority in stability, possibly due to reasons of the physical isolation of the shell and the alumina retention on the Co-Ni alloys surface caused by the reversibility of exchange equilibrium. The present work demonstrated that a surrounded structured catalyst fabricated by ion exchange (IE) with active metals physically enclosed can lead to high catalytic activity and superior stability.

chemistry, physical
Hydrogenation of levulinic acid to γ-valerolactone in dioxane over mixed MgO–Al2O3 supported Ni catalyst

Kun Jiang,Dong Sheng,Zihao Zhang,Jie Fu,Zhaoyin Hou,Xiuyang Lu

DOI: https://doi.org/10.1016/j.cattod.2016.01.056

IF: 5.3

2016-01-01

Catalysis Today

Abstract:•Ni/MgxAlyO(x+1.5y) possessed larger surface areas than those of Ni/MgO and Ni/Al2O3.•Ni/MgxAlyO(x+1.5y) were more active for LA hydrogenation than Ni/MgO and Ni/Al2O3.•Yield of GVL at 160°C, 1h and 3MPa H2 reached 99.7% over Ni/MgAlO2.5.•Ni/MgAlO2.5 could be recycled without obvious loss of its initial activity.
Conversion of levulinic acid and formic acid into γ-valerolactone over heterogeneous catalysts.

Li Deng,Yan Zhao,Jiang Li,Yao Fu,Bing Liao,Qing-Xiang Guo

DOI: https://doi.org/10.1002/cssc.201000163

IF: 8.4

2010-01-01

ChemSusChem

Abstract:LA Lacers: The conversion of levulinic acid (LA) to γ-valerolactone is catalyzed by heterogeneous catalysts without using the external H2. Ru-P/SiO2 has been demonstrated to be a bifunctional catalyst giving a yield of 96 %. Through a two-step process, excellent performance can be achieved in eight recycling runs. Moreover, no hazardous 2-Me-THF is produced during the process. Copyright © 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.
Effective Conversion Of Biomass-Derived Ethyl Levulinate Into Gamma-Valerolactone Over Commercial Zeolite Supported Pt Catalysts

Chu-Bai Chen,Meng-Yuan Chen,Bakht Zada,Ying-Jie Ma,Long Yan,Qing Xu,Wen-Zhi Li,Qing-Xiang Guo,Yao Fu

DOI: https://doi.org/10.1039/c6ra24323a

IF: 4.036

2016-01-01

RSC Advances

Abstract:The synthesis of gamma-valerolactone from biomass-derived ethyl levulinate is of great importance for biomass conversion. However, development of efficient catalytic systems which are simple, commercially available, easy for preparation, and large-scale for the hydrogenation of ethyl levulinate to afford gamma-valerolactone is still necessary. Here, a series of commercial zeolite supported catalysts were synthesized by using a wet impregnation method for the systemic investigation of the hydrogenation of biomass-derived ethyl levulinate. High yield and selectivity towards GVL were achieved and varied and systematic characterizations including XRD, XPS, TEM and BET were used to investigate these catalysts. The influence of different reaction condition parameters was also investigated and discussed. The construction of zeolite supported catalysts showed broad prospects for the conversion of biomass into biofuels.
Supported copper catalysts for highly efficient hydrogenation of biomass-derived levulinic acid and gamma-valerolactone

Qing Xu,Xinglong Li,Tao Pan,Chuguo Yu,Jin Deng,Qingxiang Guo,Yao Fu

DOI: https://doi.org/10.1039/c5gc01454a

IF: 9.8

2016-01-01

Green Chemistry

Abstract:Levulinic acid (LA) is one of the most significant cellulose-derived compounds. gamma-Valerolactone (GVL) and 1,4-pentanediol (1,4-PDO) are considered to be important chemical intermediates. Direct conversion of LA to GVL and GVL to 1,4-PDO was achieved via chemoselective hydrogenation by supported copper catalysts. We studied the transformation of LA to GVL in water and alcohol, and the pathway of the reaction was also studied. LA was converted to GVL catalyzed by the Cu (30%)-WO3 (10%)/ZrO2-CP-300 catalyst at 413 K in ethanol with 81% yield, while 84% GVL was obtained with the Cu (30%)/ZrO2-OG-300 catalyst in water at 393 K. Furthermore, 1,4-PDO was produced from GVL in excellent selectivities (>90%) using the Cu-TiO2/ZrO2-CP-600 catalyst.
Highly efficient CuNi-ZrO2 nanocomposites for selective hydrogenation of levulinic acid to γ-valerolactone

Yufang Ding,Junli Sun,Rongqi Hu,Daiping He,Xulin Qiu,Chengying Luo,Ping Jiang

DOI: https://doi.org/10.1039/d4ra04960h

2024-08-29

Abstract:CuNi-ZrO2 nanocomposites were prepared by a simple coprecipitation technique of copper, nickel and zirconium ions with potassium carbonate. The structures of the nanocomposites were characterized by N2 physical adsorption, XRD, H2-TPR and STEM-EDS. The Cu0.05Ni0.45-ZrO2 nanocomposite showed outstanding catalytic performance in hydrogenation of levulinic acid (LA) to γ-valerolactone (GVL), especially NaOH solution (0.5 mol L-1) as a solvent. 100% LA conversion and > 99.9% GVL selectivity are achieved over Cu0.05Ni0.45-ZrO2 catalyst at 200 °C, 3 MPa for 1.5 h. Characterization results suggest that the excellent reactivity of the Cu0.05Ni0.45-ZrO2 may be due to a better reducibility of nickel oxide in the CuONiO-ZrO2, dispersion of Ni in the Cu0.05Ni0.45-ZrO2 compared to nickel oxide in the NiO-ZrO2 and Ni in the Ni0.5-ZrO2 and promotion of OH-. The results demonstrate that the Cu0.05Ni0.45-ZrO2 nanocomposite has potential to realize high efficiency and low-cost synthesis of liquid fuels from biomass.

Highly Efficient Conversion of Biomass-Derived Levulinic Acid into Γ-Valerolactone over Ni/MgO Catalyst

Highly efficient Ni-Mn/SiO<sub>2</sub> catalyst for the selective hydrogenation of biomass-derived levulinic acid to -valerolactone under mild conditions

Hydrogenation of Levulinic Acid over Nickel Catalysts Supported on Aluminum Oxide to Prepare Γ-Valerolactone

Highly Efficient Selective Hydrogenation of Levulinic Acid to Γ-Valerolactone over Cu–Re/TiO2 Bimetallic Catalysts

Catalytic Hydrogenation of Levulinic Acid to Gamma-Valerolactone over Ni/ZrO2

Selective Production of gamma-Valerolactone and Valeric Acid in One-Pot Bifunctional Metal Catalysts

Selective Production of γ-Valerolactone from Biomass-Derived Levulinic acid over Ni/CMK-3 catalyst

Selective Conversion of Levulinic Acid to Gamma-Valerolactone over Ni-based Catalysts: Impacts of Catalyst Formulation on Sintering of Nickel

Efficient Hydrogenation of Biomass-derived Levulinic Acid into γ-Valerolactone Under Mild Condition

Catalytic Conversion of Biomass-Derived Levulinic Acid into Γ-Valerolactone Using Iridium Nanoparticles Supported on Carbon Nanotubes

Highly Efficient Hydrogenation of Levulinic Acid into Γ‐valerolactone Using an Iron Pincer Complex

Catalytic Hydrogenation of Levulinic Acid for the Preparation of γ-Valerolactone by CuAgZrO2-graphene Nanocomposite

Synthesis of Γ-Valerolactone from Ethyl Levulinate Hydrogenation and Ethyl 4-Hydroxypentanoate Lactonization over Supported Cu-Ni Bimetallic, Bifunctional Catalysts

Conversion of Levulinate Ester and Formic Acid into Γ-Valerolactone Using a Homogeneous Iron Catalyst

Production of γ-Valerolactone from Methyl Levulinate via Catalytic Transfer Hydrogenation on Nickel-Copper Oxide Catalyst

Ion-Exchange Synthesis of Surrounded CoNi@Al2O3 Catalyst for Levulinic Acid Hydrogenation to γ-Valerolactone under Mild Conditions

Hydrogenation of levulinic acid to γ-valerolactone in dioxane over mixed MgO–Al2O3 supported Ni catalyst

Conversion of levulinic acid and formic acid into γ-valerolactone over heterogeneous catalysts.

Effective Conversion Of Biomass-Derived Ethyl Levulinate Into Gamma-Valerolactone Over Commercial Zeolite Supported Pt Catalysts

Supported copper catalysts for highly efficient hydrogenation of biomass-derived levulinic acid and gamma-valerolactone

Highly efficient CuNi-ZrO2 nanocomposites for selective hydrogenation of levulinic acid to γ-valerolactone