Highly Efficient Selective Hydrogenation of Levulinic Acid to Γ-Valerolactone over Cu–Re/TiO2 Bimetallic Catalysts

Yingxin Liu,Kai Liu,Meihua Zhang,Kaiyue Zhang,Jiao Ma,Shuwen Xiao,Zuojun Wei,Shuguang Deng

DOI: https://doi.org/10.1039/d1ra05804e

IF: 4.036

2022-01-01

RSC Advances

Abstract:Herein, we report a highly efficient and recyclable Cu–Re(1 : 1)/TiO2 bimetallic catalyst for liquid phase hydrogenation of levulinic acid to γ-valerolactone.

What problem does this paper attempt to address?

Highly efficient selective hydrogenation of levulinic acid to γ-valerolactone over Cu–Re/TiO 2 bimetallic catalysts

Yingxin Liu,Kai Liu,Meihua Zhang,Kaiyue Zhang,Jiao Ma,Shuwen Xiao,Zuojun Wei,Shuguang Deng

DOI: https://doi.org/10.1039/d1ra05804e

IF: 4.036

2022-01-01

RSC Advances

Abstract:Herein, we report a highly efficient and recyclable Cu–Re(1 : 1)/TiO 2 bimetallic catalyst for liquid phase hydrogenation of levulinic acid to γ-valerolactone.

chemistry, multidisciplinary
Low Loading of CoRe/TiO<sub>2</sub> for Efficient Hydrodeoxygenation of Levulinic Acid to -Valerolactone

Zuojun Wei,Qing Li,Yuran Cheng,Mei Dong,Zuyi Zhang,Xinmiao Zhu,Yingxin Liu,Yong Sun

DOI: https://doi.org/10.1021/acssuschemeng.1c03380

IF: 8.4

2021-01-01

ACS Sustainable Chemistry & Engineering

Abstract:CoRe bimetallic catalysts with low loading were designed for hydrodeoxygenation of levulinic acid to gamma-valerolactone. Results show that the 1 wt % Co0.5Re0.5/TiO2 catalyst achieved the highest yield of gamma-valerolactone (>99%) at 220 degrees C, 3 h, a 1,4-dioxane solvent and Co/levulinic acid molar ratio of 1:1760, with a turnover frequency (TOF) of 1328 h(-1). The catalyst can be reused four times with only slight activity loss. The catalyst was characterized with various physicochemical measurements, and its adsorption styles with H-2 and levulinic acid were calculated by density functional theory. The results reveal that four main factors are related to its excellent catalytic performance. First, the Re oxides synergize with Co by spillover of the dissociated H atoms, which increases the apparent dispersion of Co and promotes the reaction. Second, the low loading of 1 wt % allowed the metal nanoparticles to be well dispersed with a very fine size of ca. 1.24 nm, which may expose more active sites to the substrate and result in a higher catalytic efficiency. Third, CoRe formed an amorphous alloy with the formula Co-ReO1.6, which showed a synergistic effect during the reaction. Finally, the TiO2 support was nonporous and hydrophilic, which would be beneficial for the mass diffusion of the reaction components to be adsorbed/desorbed onto the vicinity of the metallic active sites and lead to a high TOF in the hydrodeoxygenation process.
Highly Efficient Selective Hydrogenation of Cinnamaldehyde to Cinnamyl Alcohol over CoRe/TiO2 Catalyst.

Mengting Chen,Yun Wang,Limin Jiang,Yuran Cheng,Yingxin Liu,Zuojun Wei

DOI: https://doi.org/10.3390/molecules28083336

IF: 4.6

2023-01-01

Molecules

Abstract:Allylic alcohols typically produced through selective hydrogenation of α,β-unsaturated aldehydes are important intermediates in fine chemical industry, but it is still a challenge to achieve its high selectivity transformation. Herein, we report a series of TiO2-supported CoRe bimetallic catalysts for the selective hydrogenation of cinnamaldehyde (CAL) to cinnamyl alcohol (COL) using formic acid (FA) as a hydrogen donor. The resultant catalyst with the optimized Co/Re ratio of 1:1 can achieve an exceptional COL selectivity of 89% with a CAL conversion of 99% under mild conditions of 140 °C for 4 h, and the catalyst can be reused four times without loss of activity. Meanwhile, the Co1Re1/TiO2/FA system was efficient for the selective hydrogenation of various α,β-unsaturated aldehydes to the corresponding α,β-unsaturated alcohols. The presence of ReOx on the Co1Re1/TiO2 catalyst surface was advantageous to the adsorption of C=O, and the ultrafine Co nanoparticles provided abundant hydrogenation active sites for the selective hydrogenation. Moreover, FA as a hydrogen donor improved the selectivity to α,β-unsaturated alcohols.
Highly efficient Ni-Mn/SiO<sub>2</sub> catalyst for the selective hydrogenation of biomass-derived levulinic acid to -valerolactone under mild conditions

Mengting Chen,Qifeng Zhong,Jiao Ma,Zhiyang Zhang,Yingxin Liu,Zuojun Wei,Shuguang Deng

DOI: https://doi.org/10.1039/d3nj01010d

IF: 3.3

2023-01-01

New Journal of Chemistry

Abstract:Hydrogenation of levulinic acid (LA) to gamma-valerolactone (GVL) is a key reaction in the conversion of biomass to renewable fuels and value-added chemicals. Developing low-cost, highly efficient and reusable non-noble metal-based heterogeneous catalysts is vital but challenging. Herein, non-noble Ni-Mn/SiO2 catalysts with a low Ni loading (2.0 wt%) were designed for the selective hydrogenation of LA to GVL. The results showed that the optimal Ni-Mn/SiO2 (Ni/Mn = 2) catalyst with well-dispersed and small-sized metal nanoparticles (2.21 nm) and moderate acid sites exhibited excellent activity and selectivity and achieved a 100% yield of GVL in a 1,4-dioxane solvent under mild reaction conditions (e.g., 0.8 mol% Ni, 140 degrees C and 2.0 MPa H-2) for 5.5 h and a 100% GVL yield at 180 degrees C for 2 h with a turnover frequency (TOF) of 190.2 h(-1), which is better than most non-noble metal catalysts reported. Furthermore, the catalyst exhibited excellent reusability and could be recycled at least five times with only slight activity loss. This work provides new insights for the rational design of highly efficient and stable non-noble metal catalysts for the conversion of LA to GVL.
An Efficient and Reusable Embedded Ru Catalyst for the Hydrogenolysis of Levulinic Acid to Γ‐valerolactone

Zuojun Wei,Jiongtao Lou,Chuanmin Su,Dechao Guo,Yingxin Liu,Shuguang Deng

DOI: https://doi.org/10.1002/cssc.201601769

IF: 8.4

2017-01-01

ChemSusChem

Abstract:To achieve a higher activity and reusability of a Ru-based catalyst, Ru nanoparticles were embedded in N-doped mesoporous carbon through a hard-template method. The catalyst showed excellent catalytic performance (314h(-1) turnover frequency) and recyclability (reusable five times with 3% activity loss) for the hydrogenolysis of levulinic acid to -valerolactone. Compared with the mesoporous carbon without N-doping and conventional activated carbon, the introduction of N-dopant effectively improved the dispersion of Ru nanoparticles, decreased the average size of Ru nanoparticles to as small as 1.32nm, and improved the adsorption of levulinic acid, which contributed to the increase in the activity of the catalyst. Additionally, the embedding method increased the interaction between Ru nanoparticles and carbon support in contrast with the conventional impregnation method, thus preventing the Ru nanoparticles from migration, aggregation, and leaching from the carbon surface and therefore increasing the reusability of the catalyst.
Pt-Re/rGO Bimetallic Catalyst for Highly Selective Hydrogenation of Cinnamaldehyde to Cinnamylalcohol

Zuojun Wei,Xinmiao Zhu,Xiaoshuang Liu,Haiqin Xu,Xinghua Li,Yaxin Hou,Yingxin Liu

DOI: https://doi.org/10.1016/j.cjche.2018.04.022

IF: 3.8

2018-01-01

Chinese Journal of Chemical Engineering

Abstract:In the present work, a series of Pt-based catalysts, alloyed with a second metal, i.e., Re, Sn, Er, La, and Y, and supported on activated carbon, ordered mesoporous carbon, N-doped mesoporous carbon or reduced graphene oxide(rGO), have been developed for selective hydrogenation of cinnamaldehyde to cinnamylalcohol. Re and rGO were proved to be the most favorable metal dopant and catalyst support, respectively. Pt 50 Re 50 /rGO showed the highest cinnamylalcohol selectivity of 89% with 94% conversion of cinnamaldehyde at the reaction conditions of 120 °C, 2.0 MPaH 2 and 4 h.
Catalytic Hydrogenation of Levulinic Acid to Gamma-Valerolactone over Ni/ZrO2

Dong Sheng,Jie Fu,Xiuyang Lv

2016-01-01

Abstract:Five kinds of nickel supported zirconia (Ni/ZrO2) catalysts were prepared and characterized by N2 physisorption, X-Ray diffraction and transmission electron microscope(TEM) analysis. The effects of nickel loading and different reaction conditons on the catalytic activity were studied. The results showed that the conversion of levulinic acid increased with the increase of nickel content. It was found that the highest conversion could be achieved over 50 % Ni/ZrO2 and the highest turnover frequency(TOF) was obtained over 30% Ni/ZrO2. The reaction was accelerated with the increase of reaction temperature and much favored in dioxane than in water. The highest conversion of levulinic acid (99.1%) and yield of gamma-valerolactone (91.6%) were achieved after 9 hours under the conditions of 200℃ and hydrogen pressure of 5 MPa in dioxane.
Hydrogenation of Levulinic Acid over Nickel Catalysts Supported on Aluminum Oxide to Prepare Γ-Valerolactone

Jie Fu,Dong Sheng,Xiuyang Lu

DOI: https://doi.org/10.3390/catal6010006

IF: 3.9

2016-01-01

Catalysts

Abstract:Four types of nickel catalysts supported on aluminum oxide (Ni/Al2O3) with different nickel loadings were synthesized using the co-precipitation method and were used for the hydrogenation of levulinic acid (LA) to prepare γ-valerolactone (GVL). The synthesized Ni/Al2O3 catalysts exhibited excellent catalytic activity in dioxane, and the activity of the catalysts was excellent even after being used four times in dioxane. The catalytic activity in dioxane as a solvent was found to be superior to the activity in water. Nitrogen physisorption, X-ray diffraction, and transmission electron microscopy were employed to characterize the fresh and used catalysts. The effects of the nickel loading, temperature, hydrogen pressure, and substrate/catalyst ratio on the catalytic activity were investigated.
Levulinic acid hydrogenation to γ-valerolactone over single Ru atoms on a TiO 2 @nitrogen doped carbon support

Kaili Zhang,Qinglei Meng,Haihong Wu,Tongying Yuan,Shitao Han,Jianxin Zhai,Bingxiao Zheng,Caiyun Xu,Wei Wu,Mingyuan He,Buxing Han

DOI: https://doi.org/10.1039/d0gc04108d

IF: 9.8

2021-01-01

Green Chemistry

Abstract:TiO 2 @nitrogen doped porous carbon dispersed single Ru atom catalyst (Ru/TiO 2 @CN) efficiently transforms levulinic acid into γ-valerolactone at room temperature in water with a turnover frequency of 278 mol GVL mol Ru −1 h −1 at complete conversion.

chemistry, multidisciplinary,green & sustainable science & technology
Highly Efficient Hydrogenation of Levulinic Acid into Γ‐valerolactone Using an Iron Pincer Complex

Yuxuan Yi,Huiying Liu,Ling-Ping Xiao,Bo Wang,Guoyong Song

DOI: https://doi.org/10.1002/cssc.201800435

IF: 8.4

2018-01-01

ChemSusChem

Abstract:The search for nonprecious-metal-based catalysts for the synthesis of gamma-valerolactone (GVL) through hydrogenation of levulinic acid and its derivatives in an efficient fashion is of great interest and importance, as GVL is an important a sustainable liquid. We herein report a pincer iron complex that can efficiently catalyze the hydrogenation of levulinic acid and methyl levulinate into GVL, achieving a turnover number of up to 23000 and a turnover frequency of 1917 h(-1). This iron-based catalyst also enabled the formation of GVL from various biomass-derived carbohydrates in aqueous solution, thus paving a new way toward a renewable chemical industry.
Highly efficient CuNi-ZrO2 nanocomposites for selective hydrogenation of levulinic acid to γ-valerolactone

Yufang Ding,Junli Sun,Rongqi Hu,Daiping He,Xulin Qiu,Chengying Luo,Ping Jiang

DOI: https://doi.org/10.1039/d4ra04960h

2024-08-29

Abstract:CuNi-ZrO2 nanocomposites were prepared by a simple coprecipitation technique of copper, nickel and zirconium ions with potassium carbonate. The structures of the nanocomposites were characterized by N2 physical adsorption, XRD, H2-TPR and STEM-EDS. The Cu0.05Ni0.45-ZrO2 nanocomposite showed outstanding catalytic performance in hydrogenation of levulinic acid (LA) to γ-valerolactone (GVL), especially NaOH solution (0.5 mol L-1) as a solvent. 100% LA conversion and > 99.9% GVL selectivity are achieved over Cu0.05Ni0.45-ZrO2 catalyst at 200 °C, 3 MPa for 1.5 h. Characterization results suggest that the excellent reactivity of the Cu0.05Ni0.45-ZrO2 may be due to a better reducibility of nickel oxide in the CuONiO-ZrO2, dispersion of Ni in the Cu0.05Ni0.45-ZrO2 compared to nickel oxide in the NiO-ZrO2 and Ni in the Ni0.5-ZrO2 and promotion of OH-. The results demonstrate that the Cu0.05Ni0.45-ZrO2 nanocomposite has potential to realize high efficiency and low-cost synthesis of liquid fuels from biomass.
Synthesis of Γ-Valerolactone from Ethyl Levulinate Hydrogenation and Ethyl 4-Hydroxypentanoate Lactonization over Supported Cu-Ni Bimetallic, Bifunctional Catalysts

Yafei Li,Xiaocheng Lan,Boyang Liu,Tiefeng Wang

DOI: https://doi.org/10.1016/j.jiec.2021.11.048

IF: 6.76

2021-01-01

Journal of Industrial and Engineering Chemistry

Abstract:A stable and highly efficient supported Cu-Ni catalysts for the conversion of ethyl levulinate (EL) to gamma-valerolactone (GVL) was developed. The catalysts were characterized by XRD, TEM, TPD, TPR, and XPS. The support effect of metal oxides (Al2O3, SiO2, ZrO2, and TiO2) revealed that Cu-Ni supported on Al2O3 showed the highest activity for EL hydrogenation to ethyl 4-hydroxypentanoate (EHP) and the subsequent intramolecular esterification of EHP to GVL. EHP intramolecular esterification to GVL in the ethanol solution was a reversible reaction with an equilibrium constant of 24 at 453 K. A simplified reaction kinetic network was established. The solvent had a significant influence on the reaction equilibrium and the catalyst stability. Cu-Ni/Al2O3 in n-hexane solvent gave a higher GVL yield than that in ethanol solvent, and showed better recyclability than that in toluene solvent. With optimizing the conditions, CuNi/Al2O3 gave 99.9% conversion and 98% selectivity to GVL with a space-time yield of 1.13 gGVL gcat(-1) h(-1) in n-hexane solvent with good recyclability. (C) 2021 The Korean Society of Industrial and Engineering Chemistry. Published by Elsevier B.V. All rights reserved.
An Efficient and Reusable Bimetallic Ni3Fe NPs@C Catalyst for Selective Hydrogenation of Biomass-Derived Levulinic Acid to Γ-Valerolactone

Haojie Wang,Chun Chen,Haimin Zhang,Guozhong Wang,Huijun Zhao

DOI: https://doi.org/10.1016/s1872-2067(18)63105-5

2018-01-01

CHINESE JOURNAL OF CATALYSIS (CHINESE VERSION)

Abstract:Bimetallic nanostructures have attracted great interest as efficient catalyst to enhance activity, selectivity and stability in catalytical conversion. Herein, we report a facile one-pot carbothermal route to in-situ controllable synthesize heterogeneous bimetallic Ni3Fe NPs@C nanocatalyst. The X-ray diffraction, transmission electron microscopy, X-ray photoelectron spectroscopy and N-2 adsorption-description results reveal that the Ni3Fe alloy nanoparticles are evenly embedded in carbon matrix. The as-prepared Ni3Fe NPs@C catalyst shows excellent selective hydrogenation catalytic performance toward the conversion of levulinic acid (LA) to gamma-valerolactone (GVL) via both direct hydrogenation (DH) and transfer hydrogenation (TH). In DH of LA, the bimetallic catalyst achieved a 93.8% LA conversion efficiency with a 95.5% GVL selectivity and 38.2 mmol g(-1) h(-1) GVL productivity (under 130 degrees C, 2MPa H-2 within 2 h), which are 6 and 40 times in comparison with monometallic Ni NPs@C and Fe NPs@C catalysts, respectively. In addition, the identical catalyst displayed a full conversion of LA with almost 100% GVL selectivity and 167.1 mmol g(-1) h(-1) GVL productivity at 180 degrees C within 0.5 h in TH of LA. Under optimal reaction conditions, the DH and TH catalytic performance of 500-Ni3Fe NPs@C(3:1) catalyst for converting LA to GVL is comparable to the state-of-the-art noble-based catalysts. The demonstrated capability of bimetallic catalyst design approach to introduce dual-catalytic functionality for DH and TH reactions could be adoptable for other catalysis processes. (C) 2018, Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by Elsevier B.V. All rights reserved.
Catalytic Hydrogenation of Levulinic Acid for the Preparation of γ-Valerolactone by CuAgZrO2-graphene Nanocomposite

Yufeng Jia,Hui Lv,Jingbo Mao,Jinxia Zhou

DOI: https://doi.org/10.1039/d3nj05088b

IF: 3.3

2024-03-27

New Journal of Chemistry

Abstract:Hydrogenation of biomass-derived levulinic acid (LA) could produce a high value-added compound, gamma-valerolactone (GVL). However, metal leaching is a major issue in the efficient production of GVL from LA due to the acidity of LA. Some endeavors have tended to focus on the external factors of the catalysts for preventing metal leaching, such as reaction at high temperature and H2 pressure or the esterification of LA with alcohols. Focusing on the catalyst itself, in this work, metal leaching was solved by the selection of suitable catalyst compositions and preparation methods. The CuAgZrGO catalyst was synthesized by regulating the pH of the precipitation system to achieve a one-pot layered assembly of Zr4+, Cu2+, and Ag+ components on the graphene oxide (GO) surface at the atomic level. The catalyst without reduction pretreatment resulted in the complete conversion of LA and achieved approximately 100% yield of GVL, and metal leaching in the LA aqueous phase could be substantially prevented. Under mild reaction conditions, the catalyst exhibits good stability after four times of recycling in the aqueous phase. The positive-titration co-precipitation method controls the Ag more scattered on the surface of Cu and Zr precipitate, which makes CuAgZrGO to be metal-leaching-resistant catalyst for aqueous-phase hydrogenation of LA.

chemistry, multidisciplinary
The solvent-free hydrogenation of butyl levulinate to γ-valerolactone and 1,4-pentanediol over skeletal Cu-Al-Zn catalyst

Bo Li,Haijun Guo,Zhen Xiong,Lian Xiong,Shimiao Yao,Mengkun Wang,Hairong Zhang,Xinde Chen

DOI: https://doi.org/10.1016/j.mcat.2023.113046

IF: 4.6

2023-03-14

Molecular Catalysis

Abstract:γ-valerolactone (GVL) is a sustainable chemical, which can be obtained by hydrogenation of levulinic acid (LA) and levulinate. Herein, we reported a solvent-free hydrogenation of butyl levulinate (BL) to GVL and 1,4-pentanediol (1,4-PDO) over a skeletal Cu-Al-Zn catalyst. The skeletal Cu-Al-Zn catalyst was prepared from Devarda's alloy by alkali leaching and the catalyst was characterized by different analysis methods. The aluminum in the Devarda's alloy was dissolved by sodium hydroxide in the leaching process and many active Cu atoms were generated on the catalyst surface and the skeletal Cu-Al-Zn exhibited many micrometer-scale irregular particles with rough surface. The skeletal Cu-Al-Zn catalyst showed the excellent performance in the solvent-free hydrogenation of BL to GVL under constant hydrogen pressure (5 wt% catalyst loading, 180°C, 6 MPa of H 2 , 6 h): the LA conversion was 100%, the GVL yield was 74.75% and the 1,4-PDO yield was 25.63%. Moreover, the catalyst showed stable performance and it was reusable up to 5 times without apparent loss of activity. A stable hydrogen pressure with Zn would suppressed the dehydration of 1,4-PDO.

chemistry, physical
Efficient Hydrogenation of Biomass-derived Levulinic Acid into γ-Valerolactone Under Mild Condition

DU Xian-long,YUAN Jing,CAO Yong,LIU Yong-mei,FAN Kang-nian

DOI: https://doi.org/10.15943/j.cnki.fdxb-jns.2012.05.011

2012-01-01

Abstract:Ir/CNT,a catalyst of high-activity,was used for the hydrogenation of levulinic acid(LA) to y-valerolactone(GVL),and all the factors that affect LA hydrogenation were discussed.The variations of the fresh and used catalysts were characterized by XRD、TEM and XPS.The origin for high activity of Ir/CNT catalyst was investigated through H_2-TPD experiment.It was found that an excellent GVL yield of 99%has been obtained at 50℃and 2 MPa H_2.Finally the simulated biomass-derived substrates containing equimolar amounts of LA and formic acid can be converted into GVL in the presence of Ir/CNT catalyst with enhanced hydrogen pressure.
SSZ-39 zeolite-based Ru catalysts for selective hydrogenation of levulinic acid to γ-valerolactone: Influence of synthesis method and zeolite acidity

Amar Al-khawlani,Jiehua Bao,Xiaoli Sheng,Pingping Yu,Basheer M. Al-Maswari,Awatif Rashed Z. Almotairy,Yiwei Zhang,Zhou Yuming

DOI: https://doi.org/10.1016/j.micromeso.2024.113112

IF: 5.876

2024-03-27

Microporous and Mesoporous Materials

Abstract:Novel SSZ-39 zeolite-based Ru catalysts were synthesized by impregnation on as-synthesized metallic and protonated SSZ-39 and a one-pot synthesis strategy. The study focused on the influence of the SSZ-39 zeolite characteristics and catalyst preparation method type toward levulinic acid (LA) selective conversion to γ-valerolactone (GVL) under relatively mild reaction conditions (150 °C, 4 h and 2MPa of H 2 with H 2 O and THF as solvents). Catalysts exhibited excellent catalytic efficiency (100 % LA conversion and 98.3 % GVL selectivity) and remarkable hydrothermal stability. The results revealed a correlation between excellent catalytic activity and the structural features of the synthesized catalysts, predominantly dependent on their appropriate surface acidity (strong Lewis acid sites) and enhanced electronic interaction between Ru species and SSZ-39. The one-pot method promoted the formation of mesopores besides the zeolitic micropores present in SSZ-39; therefore, the catalyst prepared by the one-pot method (Ru/SSZ-39) showed purer SSZ-39 crystallites and a slightly larger catalytic surface area of 439 m 2 /g than the original zeolite surface area of 424 m 2 /g. In addition, the original zeolite crystals retained their morphology as spherical aggregates and remained unaffected by Ru impregnation on the metallic or protonated support during the synthesis of Ru/Na-SSZ-39 and Ru/H-SSZ-39 catalysts, respectively. Notably, it has been demonstrated that SSZ-39 zeolite effectively acts as a support for the preparation of Ru catalyst in biomass conversion reactions. Moreover, the reused catalyst exhibited consistent activity over six cycles, maintaining its structural framework without significant loss in activity.

materials science, multidisciplinary,chemistry, physical,nanoscience & nanotechnology, applied
Conversion of levulinic acid and formic acid into γ-valerolactone over heterogeneous catalysts.

Li Deng,Yan Zhao,Jiang Li,Yao Fu,Bing Liao,Qing-Xiang Guo

DOI: https://doi.org/10.1002/cssc.201000163

IF: 8.4

2010-01-01

ChemSusChem

Abstract:LA Lacers: The conversion of levulinic acid (LA) to γ-valerolactone is catalyzed by heterogeneous catalysts without using the external H2. Ru-P/SiO2 has been demonstrated to be a bifunctional catalyst giving a yield of 96 %. Through a two-step process, excellent performance can be achieved in eight recycling runs. Moreover, no hazardous 2-Me-THF is produced during the process. Copyright © 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.
Copper-based Catalysts with Tunable Acidic and Basic Sites for the Selective Conversion of Levulinic Acid/ester to Γ-Valerolactone or 1,4-Pentanediol

Yuewen Shao,Kai Sun,Qingyin Li,Qianhe Liu,Shu Zhang,Qing Liu,Guangzhi Hu,Xun Hu

DOI: https://doi.org/10.1039/c9gc01706b

IF: 9.8

2019-01-01

Green Chemistry

Abstract:Selective conversion of levulinic acid/ester to γ-valerolactone or 1,4-pentanediol was achieved over copper-based catalysts with tunable acidic and basic sites.
Role of the Cu-ZrO2 interface in the hydrogenation of levulinic acid to γ-valerolactone

Ziyi Li,Haigang Hao,Jingjing Lu,Chengming Wu,Rui Gao,Jifan Li,Chun-Ling Liu,Wen-Sheng Dong

DOI: https://doi.org/10.1016/j.jechem.2021.01.046

IF: 13.1

2021-10-01

Journal of Energy Chemistry

Abstract:Here we exquisitely fabricated Cu/ZrO2-dp catalysts with plentiful Cu-ZrO2 interfaces by depositing amorphous ZrO2 onto Cu nanoparticles for the hydrogenation of levulinic acid (LA) to γ-valerolactone (GVL). With the created plentiful Cu-ZrO2 interfaces, the optimal catalyst 3Cu/ZrO2-dp exhibited exceptional catalytic performance under mild reaction conditions, and achieved the highest GVL mass productivity of 266.0 mmol GVL·h−1·g−1 Cu, which was 12.5 and 2.3 times of Cu/ZrO2 catalysts with equivalent Cu loadings prepared by traditional impregnation (3Cu/ZrO2-im) or co-precipitation (3Cu/ZrO2-cp). As far as we know, this GVL mass productivity stood at the highest level compared with those obtained using non-noble metal catalysts under similar reaction conditions. By systematic investigation with multiple characterizations, density functional theory (DFT) calculations, and kinetic studies, it was found that interfacial active centers were created at Cu-ZrO2 interfaces, which contained oxygen vacancies (Ov), negatively charged Cuδ− and partially reduced Zr3+. The Ov favored the adsorption and activation of LA via its ketone group, while negatively charged Cuδ− was able to enhance heterolysis of H2, which resulted in the formation of H+-Cuδ− and Zr3+-H− active species via hydrogen spillover. Also, plentiful acid sites, which derived from coordinatively unsaturated and defective Zr species, generated at Cu-ZrO2 interfaces. With the cooperation of interfacial active centers (Cuδ−-Ov-Zr3+) and acid sites, the fabricated 3Cu/ZrO2-dp with plentiful Cu-ZrO2 interfaces achieved excellent catalytic performance for the hydrogenation of LA to GVL. Hence, the synergistic catalysis of Cu-ZrO2 interfaces provided an effective strategy for designing catalysts with a satisfactory performance for the hydrogenation of LA, which also can be expanded to other hydrodeoxygenation reactions.

chemistry, physical,engineering, chemical, applied,energy & fuels

Highly Efficient Selective Hydrogenation of Levulinic Acid to Γ-Valerolactone over Cu–Re/TiO2 Bimetallic Catalysts

Highly efficient selective hydrogenation of levulinic acid to γ-valerolactone over Cu–Re/TiO 2 bimetallic catalysts

Low Loading of CoRe/TiO<sub>2</sub> for Efficient Hydrodeoxygenation of Levulinic Acid to -Valerolactone

Highly Efficient Selective Hydrogenation of Cinnamaldehyde to Cinnamyl Alcohol over CoRe/TiO2 Catalyst.

Highly efficient Ni-Mn/SiO<sub>2</sub> catalyst for the selective hydrogenation of biomass-derived levulinic acid to -valerolactone under mild conditions

An Efficient and Reusable Embedded Ru Catalyst for the Hydrogenolysis of Levulinic Acid to Γ‐valerolactone

Pt-Re/rGO Bimetallic Catalyst for Highly Selective Hydrogenation of Cinnamaldehyde to Cinnamylalcohol

Catalytic Hydrogenation of Levulinic Acid to Gamma-Valerolactone over Ni/ZrO2

Hydrogenation of Levulinic Acid over Nickel Catalysts Supported on Aluminum Oxide to Prepare Γ-Valerolactone

Levulinic acid hydrogenation to γ-valerolactone over single Ru atoms on a TiO 2 @nitrogen doped carbon support

Highly Efficient Hydrogenation of Levulinic Acid into Γ‐valerolactone Using an Iron Pincer Complex

Highly efficient CuNi-ZrO2 nanocomposites for selective hydrogenation of levulinic acid to γ-valerolactone

Synthesis of Γ-Valerolactone from Ethyl Levulinate Hydrogenation and Ethyl 4-Hydroxypentanoate Lactonization over Supported Cu-Ni Bimetallic, Bifunctional Catalysts

An Efficient and Reusable Bimetallic Ni3Fe NPs@C Catalyst for Selective Hydrogenation of Biomass-Derived Levulinic Acid to Γ-Valerolactone

Catalytic Hydrogenation of Levulinic Acid for the Preparation of γ-Valerolactone by CuAgZrO2-graphene Nanocomposite

The solvent-free hydrogenation of butyl levulinate to γ-valerolactone and 1,4-pentanediol over skeletal Cu-Al-Zn catalyst

Efficient Hydrogenation of Biomass-derived Levulinic Acid into γ-Valerolactone Under Mild Condition

SSZ-39 zeolite-based Ru catalysts for selective hydrogenation of levulinic acid to γ-valerolactone: Influence of synthesis method and zeolite acidity

Conversion of levulinic acid and formic acid into γ-valerolactone over heterogeneous catalysts.

Copper-based Catalysts with Tunable Acidic and Basic Sites for the Selective Conversion of Levulinic Acid/ester to Γ-Valerolactone or 1,4-Pentanediol

Role of the Cu-ZrO2 interface in the hydrogenation of levulinic acid to γ-valerolactone