Abstract:The flow condensation heat transfer coefficient of R134a inside two helical micro-fin tubes with outer diameter of 6.35 mm and helical angles of 18o and 28o respectively were experimentally studied at a high mass flux ranging from 500 to 1100 kg m−2 s−1. The condensation temperatures are 35°C, 40°C and 45°C, and the vapor qualities ranges from 0.95 to 1.00 at the inlet section and from 0.00 to 0.05 at the outlet section. Experimental results show that there are annular and intermittent flow regimes inside the tube under experimental conditions, the ratio of annular flow region to the total heat transfer region is about 70%. The liquid film flow changes from rotational flow to coexistence of rotational and horizontal flows when the vapor quality is 0.475±0.08, 0.486±0.06 and 0.521±0.05, respectively and the corresponding saturation temperature is 35°C, 40°C and 45°C. Based on the experimental data, the heat transfer coefficient increases with increasing mass flux and fin helical angle, and with decreasing saturation temperature and Reynolds number of cooling water. In addition, the heat transfer coefficient of annular flow is greater than that of intermittent flow, in other words, the heat transfer coefficient increases with increasing vapor quality. The heat transfer coefficient obtained at high mass flux was compared with the calculated data of some published correlations used at low mass flux. It was found that most correlations underestimate the experimental heat transfer coefficient inside the micro-fin tube, and these prediction deviation increases with increasing mass flux and fin helical angle. By introducing some dimensionless numbers as well as considering the flow mechanism of liquid film inside the tube, two heat transfer coefficient correlations were proposed based on the experimental data. The ratio of liquid film thickness to fin height was used to characterize whether the liquid film flow is rotational flow or coexistence of rotational and horizontal flows in the proposed correlation, which shows a better prediction accuracy with a mean deviation of less than 7.3%.

Experimental Investigation on Two-Phase Heat Transfer of R-134a During Vaporization in a Plate Heat Exchanger with Rough Surface

Pressure Drop and Heat Transfer of Flow Boiling R134a in a Dimpled Flat Duct

Experimental Investigation on Evaporation Heat Transfer and Pressure Drop Characteristics of HFC-161 in a Horizontal Smooth Tube

Effect of Surface Roughness on the Condensation of R-134a in Vertical Chevron Gasketed Plate Heat Exchangers

Experimental investigation on the flow boiling of R134a in a plate heat exchanger with mini-wavy corrugations

Experimental Study on Evaporative Heat Transfer and Pressure Drop of R-134a in a Horizontal Dimpled Tube

Flow Boiling in Dimpled Plate Heat Exchangers with Different Geometric Parameters: Analysis of Asymmetric Channels

Enhancing the vertical downward condensation heat transfer of a plate heat exchanger by electrochemical etching

Condensation heat transfer performance of R290 in a plate heat exchanger for electric vehicle heat pumps

Experimental Study of Condensation Heat Transfer of R134a Inside the Micro-Fin Tubes at High Mass Flux

Experimental Investigation of Single-Phase Turbulent Flow of R-134a in a Multiport Microchannel Heat Sink

Heat Transfer Characteristics of Plate Heat Exchanger with Bubble Fin Using Al2O3/Water Nanofluid: Numerical Investigation

Condensation of R1234yf in a plate heat exchanger with an offset strip fin flow structure for electric vehicle heat pumps

An experimental study on two-phase flow patterns and heat transfer characteristics during boiling of R134a flowing through a multi-microchannel heat sink

Effects of Experimental Parameters on Condensation Heat Transfer in Plate Fin Heat Exchanger

Evaporation Heat Transfer Characteristics On The Outside Of Horizontal Smooth, Herringbone And Enhanced Surface 1eht Tubes

Experimental Investigation on Condensation Heat Transfer and Pressure Drop of R134a in a Plate Heat Exchanger

Thermal-hydraulic Performance of a Plate Heat Exchanger with Grooved Copper Foam

Theoretical and experimental investigation of a heat pipe heat exchanger for energy recovery of exhaust air

An Experimental Investigation on R134a Evaporation inside an Internally Discrete Inclined Grooved Tube

Experimental investigation on the condensation heat transfer coefficient and frictional pressure drop of R-513A and R-134a in commercial refrigeration tubes