Abstract:This paper presented an innovative three-dimensional vibration isolation bearing (3D-VIB) to mitigate horizontal seismic action and rail-induced vertical vibration. The 3D-VIB was composed of a thick laminated rubber bearing acting as the vertical vibration isolation module and a friction pendulum acting as the horizontal seismic isolation module. The thick laminated rubber bearing was used as a part of the slider in the friction pendulum. The compression performance of 3D-VIB was decoupled from its shear performance by concentrating the compressive deformation into the thick rubber bearing while shear deformation occurred independently in the friction pendulum module. The bearing capacity, vertical and horizontal properties of a full-scale 3D-VIB specimen were tested. In the test, the ultimate bearing capacity of 3D-VIB was 7 times that of the design compressive load of normal service condition. The vertical stiffness of the specimen under seismic vibration and vertical rail-induced vibration were tested separately. It was found that the vertical stiffness of the specimen under rail-induced vibration was 1.55 times higher than the vertical stiffness under seismic vibration. The horizontal performance of the 3D-VIB was characterized by stable parallelogram-shaped hysteretic curves similar to that of the traditional friction pendulum system. A user-defined element was developed and incorporated into ABAQUS to simulate the mechanical behavior of the 3D-VIB under different loading conditions, and simulation results agreed with the test results. The responses of a steel structure equipped with the 3D-VIB, while subjected to earthquake ground motions and rail-induced vibrations, respectively, were analyzed and compared with the non-isolated one. The analysis results suggested that with the installation of the 3D-VIB, the maximum inter-story drift ratio of the structure under maximum considered earthquake was reduced by about 88%. The average maximum transient vibration value of the rail-induced vertical vibration at the typical points of the conventional model was 86.2 dB, while that in the 3D-isolated model was 78.6 dB, the vibration reduction was 7.6 dB.

Three-Dimensional Base Isolation Using Vertical Negative Stiffness Devices

Analytical and numerical investigations of base isolation system with negative stiffness devices

Effect of Negative Stiffness Mechanism in a Vibration Isolator with Asymmetric and High-Static-low-dynamic Stiffness

A Direct Displacement-Based Design Procedure for Base-Isolated Building Structures with Lead Rubber Bearings (Lrbs)

Seismic performance improvement of a three-dimensional isolated spherical reticulated shell structure using pseudo-negative-stiffness magnetorheological dampers

An enhanced base isolation system equipped with optimal tuned mass damper inerter (TMDI)

A Novel Negative Stiffness Amplification System Based Isolation Method for the Vibration Control of Underground Structures

Nonlinear Viscous Damping-Based Negative Stiffness Isolation System with for Over-Track Complex Structures

A state-of-the-art review on negative stiffness mechanism for safer structures in seismic areas

Effectiveness in protecting rigid-block-like objects through horizontal and vertical seismic isolation

Seismic performance of advanced three-dimensional base-isolated nuclear structures in complex-layered sites

Multi-location seismic isolation approach and design for underground structures employing the negative-stiffness amplification system

Seismic protection of a single-layer spherical lattice shell structure using a separated three-dimensional isolation system

Development of an innovative three-dimensional vibration isolation bearing

Performance of a nonlinear hybrid base isolation system under the ground motions

Analysis of an Isolation System with Vertical Spring-viscous Dampers in Horizontal and Vertical Ground Motion

Application of Supplementary Inerter-Based Damping Devices Alongside Unbonded Fiber-Reinforced Elastomeric Isolators

Horizontal Shaking Table Tests on a Four-Story Prototype Structure Using Multi-Dimensional Earthquake Isolation and Mitigation Devices

Base Isolation for Seismic Retrofitting of a Multiple Building Structure: Design, Construction, and Assessment

Comprehensive Assessment of the Seismic Performance of an Innovative Hybrid Semiactive and Passive State Control System for a Low-Degree-of-Freedom Structure Using Real-Time Hybrid Simulation

Seismic control of multi-degrees-of-freedom structures by vertical mass isolation method using MR dampers