Abstract:A previous study on quenching and partitioning (QP) steel showed that the transformation-induced plasticity (TRIP) effect strongly depends on the stress triaxiality and Lode angle parameters during the plastic deformation. However, only the impact of stress states on the linear hardening response (first-order effect) was investigated, assuming its yield and plastic flow evolution (second-order effect) follow isotropic behavior for both tension and compression. The high-order effects of phase transformation on plasticity are still elusive and difficult to incorporate owing to the inconsistent usage of the equivalent strain in kinetics law and constitutive modeling. In this study, the hardening law, considering martensitic transformation, was utilized in conjunction with a strength differential (SD) effect-induced asymmetric yield function based on the proposed work-conjugate framework. The contradiction where the previous model correlates the martensitic transformation law based on the von Mises strain and the mechanical responses based on the normalized plastic work-per-unit material (or the work-conjugate equivalent strain) was eliminated. This elimination imposed the phase transformation influence into size evolution of the yield surface for QP980 because the effective stress directly correlated with the martensitic transformation using the work-conjugate equivalent strain. One can use any yield function in conjunction with this work-conjugate framework to correlate the martensitic transformation and its impact on the mechanical behavior for both first- and second-order effects. Thus, the yield surface of QP980 steel was stably normalized through asymmetric function under different plastic strains and deformation modes. The SD effect of QP980 steel has proven to be anisotropic and the martensitic transformation has negligible impact on the shape evolution of its yield surface. The pressure-dependent phenomenon in the plastic flow behavior of the employed QP steel suggested that its volume change during the plastic deformation can be neglected. The correlation between the microstructure volume fraction, evolving yield surface, and the stress–strain response under nonlinear loadings (Bauschinger effect) was predicted accurately. The forming limit imperfection analysis served as a typical application, where the phase transformation was further correlated with the localized necking phenomenon. The framework to understand the impact of microstructure evolution in QP steel sheets on its final forming limits was provided, suggesting that an optimized strain path design will greatly enhance the accumulated plastic limit before the localized necking.

Failure Investigation for QP Steel Sheets under uniaxial and Equal-Biaxial Tension Conditions

Phase transformation and plastic behavior of QP steel sheets: Transformation kinetics-informed modeling and forming limit prediction

Modelling of Q&P Steel Heat Treatment Process Based on Finite Element Method

Fracture of dual phase steel sheets under uniaxial tension (I): experimental study with dic techniques

Experimental and Numerical Study on Strain Path and Crystal Orientation Dependences of Phase Transformation Behaviors of QP1180 Steel

Evolving asymmetric yield surfaces of quenching and partitioning steels: Characterization and modeling

Quasi-Situ Characterization of Retained Austenite Orientation in Quenching and Partitioning Steel via Uniaxial Tensile Tests

Study on the Mechanical Behavior of Quenching and Partitioning Sheet Steel and Its Application to Stamping of a Hinge Pillar Inner Panel

In-situ Investigation Via High Energy X-ray Diffraction of Stress-Induced(0002)α→(110)β Transformation in a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr Alloy

Experimental characterization and modeling of complex anisotropic hardening in quenching and partitioning (Q&P) steel subject to biaxial non-proportional loadings

Real-Time in Situ Neutron Diffraction Investigation of Phase-Specific Load Sharing in a Cold-Rolled TRIP Sheet Steel

Investigation of ductile damage in dual phase steel during tensile deformation by in situ X-ray computed tomography

Effect of alloying and microstructure on formability of advanced high-strength steels processed via quenching and partitioning

Understanding the damage initiation and growth mechanisms of two DP800 dual phase grades

Effect of compressive load on texture evolution and anisotropic behavior of dual-phase steel under biaxial loading in complete σ 11 -σ 22 space

Investigation of evolving yield surfaces of dual-phase steels

Failure behavior and mechanical properties in the resistance spot welding of quenched and partitioned (Q&P) steels

Study on Dynamic Deformation Behavior of Q&P Steel with Heterogeneous Ultrafine-Grain Ferrite Matrix

The Study and Application on Ductile Fracture Criterion of Dual Phase Steels During Forming

Abnormal Strain Rate‐Dependent Work‐Hardening Behavior in Quenching and Partitioning Steel