Abstract:In ITER, pellets are calculated to require more than 8 times the mass than currently planned to reliably trigger ELMs. Unmitigated heat flux impulses from edge-localized modes (ELMs) are intolerable in ITER at full power and current. Therefore, ITER operation relies on multiple approaches to control ELM heat fluxes. One method is pellet ELM pacing to instigate small rapid ELMs with low heat flux. Predicting the performance of pellet pacing is critical for ITER, which is expected to operate in a regime with a low-collisionality, peeling-limited pedestal. However, to trigger ELMs the local pressure increase in the expanding pellet cloud pushes the equilibrium over the ballooning stability limit. In this work, linear and nonlinear M3D-C1 simulations are used to predict pellet mass thresholds in DIII-D discharges and ITER scenarios with peeling-limited pedestals. It is found that the distance of the equilibrium's operational point from the ballooning branch of the pedestal stability boundary strongly changes thresholds. Linear M3D-C1 simulations find a strong dependence of the pellet mass threshold on the poloidal injection location for ITER's 15 MA, Q=10 scenario. The required pellet mass at the planned injection locations is 8 to 17 times larger than currently considered. However, such linear simulations do not include pellet ablation physics or time evolution of density and temperature. A new scheme of 2D nonlinear simulations, coupled with linear stability analysis at various steps throughout the nonlinear time evolution, was developed to include such physics and improve on the linear results. These new nonlinear-to-linear simulations confirm previous findings. This result suggests that pellet ELM triggering in ITER could require pellets much larger than those currently planned, which makes ELM-pacing operationally challenging. On the other hand, fueling pellets injected from the high-field side will likely not unintentionally trigger ELMs in an otherwise ELM-stable plasma.

Numerical Simulation of Li-pellet Injection Experiments for ELM-pacing in EAST

ELM Mitigation by Supersonic Molecular Beam Injection into the H-mode Pedestal in the HL-2A Tokamak

Simulation of Li-pellet triggered ELM in EAST with an impurity model implemented under BOUT++ framework

Numerical Simulation of Lithium Granule Injection in Tokamak Edge Plasma

Simulation of triggering and evolution of ELM by pellet injection in EAST under BOUT++ framework

First Observations of ELM Triggering by Injected Lithium Granules in EAST

Injected Mass Deposition Thresholds for Lithium Granule Instigated Triggering of Edge Localized Modes on EAST

ELM Frequency Enhancement and Discharge Modification Through Lithium Granule Injection into EAST H-modes

Numerical Simulation of Fueling Pellet Ablation and Transport in the EAST H-mode Discharge

ELM Mitigation by Means of Supersonic Molecular Beam and Pellet Injection on the EAST Superconducting Tokamak

Impacts of Lithium Injection Positions on Lithium Transport and Heat Flux on EAST with EMC3-EIRENE Modelling

Numerical Simulation of Li Pellet Ablation in the H-mode Pedestal Region

Prediction of pellet mass thresholds for ELM triggering in low-collisionality, ITER-like discharges

First Results of ELM Triggering with a Multichamber Lithium Granule Injector into EAST Discharges

Type-I ELM Mitigation by Continuous Lithium Granule Gravitational Injection into the Upper Tungsten Divertor in EAST

Numerical simulation of the effect of pellet injection on ELMs

Features of Spontaneous and Pellet-Induced ELMs on the HL-2A Tokamak

Design of a Centrifugal Acceleration System for High Velocity Injection of Impurity Pellet into EAST Tokamak

Comparing spontaneous and pellet-triggered ELMs via non-linear extended MHD simulations

Numerical Simulation of E×B Drift Effects on Fueling Pellet Ablation and Transport in EAST

Density Compensation with Pellet Fueling During ELM Suppression with N = 4 RMP on Metal-Wall EAST Tokamak