Abstract:Twinning induced plasticity (TWIP) steel exhibits high strength and exceptional plasticity due to the formation of extensive twin under mechanical load and its ultimate tensile strength and elongation to failure ductility-value can be as high as 5x10(4) MPa.%, which provide a new choice for automobile in developing the light-weight and improving safety. Generally, due to the texture was formed during process of plastic deformation, metal material appear anisotropic behavior. The deformation mechanisms, responsible for this high strain hardening, are related to the strain-induced microstructural changes, which was dominated by slip and twinning. Different deformation mechanisms, which can be activated at different stages of deformation, will strongly influence the stress strain response and the evolution of the microstructure. In this work, to predict the texture evolution under different loading conditions and understand these two deformation mechanisms of plastic deformation process, a polycrystal plasticity constitutive model of TWIP steel coupling slip and twinning was developed based on the crystal plasticity theory and single crystal plasticity constitutive model. A polycrystal homogenization method to keep geometry coordination and stress balance adjacent grains was used, which connected the state variables of single crystal and polycrystal. And then the model was implemented and programed based on the ABAQUS/UMAT platform. The texture evolution was obtained by EBSD at strain 0.27 and 0.60, respectively. The fmite element models of tensile, compression and torsion processes were built by using the constitutive model. The mechanical response and texture evolution during plastic deformation process of TWIP steel were analyzed. The results show that with the increasing of the strain, the strain hardening phenomenon and texture density enhanced during the tensile process. Although texture types changed, texture density unchanged during the compression process. Owing to deformation increasing along the diameter direction, there is no obvious texture inside the cylinder when torsion deformation is small, texture emerged and enhanced gradually with the increasing of strain.

Crystal Plasticity Modeling of Texture Evolution of Aluminum Single Crystal Processed by High Pressure Torsion

Modelling of Texture Evolution in High Pressure Torsion by Crystal Plasticity Finite Element Method

Study of Anisotropic Plastic Behavior in High Pressure Torsion of Aluminum Single Crystal by Crystal Plasticity Finite Element Method

A Study of Plastic Deformation Behavior During High Pressure Torsion Process by Crystal Plasticity Finite Element Simulation

A Study on the Texture Evolution Mechanism of Nickel Single Crystal Deformed by High Pressure Torsion

Crystal Plasticity Modeling of Texture Evolution and Heterogeneity in Equal Channel Angular Pressing of Aluminum Single Crystal

Crystal Plasticity Investigation of Texture Evolution of Al Single Crystal During Extrusion Through a Bent Channel

Anisotropic Plasticity of Nanocrystalline Ti:A Molecular Dynamics Simulation

Investigation on Plastic Flow Behaviors of FCC Polycrystalline Aluminum under Pre-Cyclic Tension-Compression Loading: Experiments and Crystal Plasticity Modeling.

Heterogeneous Deformation and Damage Mechanisms in Multi-Phase TA15 Ti-alloy: Insights from Experiments Informed Damage-Crystal Plasticity Modelling

Investigation Of Grain Refinement Mechanism Of Nickel Single Crystal During High Pressure Torsion By Crystal Plasticity Modeling

Effect of Hardening Models on the Prediction of Deformation Textures for Polycrystalline

The Evolutions of Microstructure, Texture and Hardness of A1050 Deformed by HPT at the Transition Area

Texture evolution and deformation - induced amorphization in high pressure torsion of W

Crystal Plasticity Finite Element Modeling of Necking of Pure Aluminum During Uniaxial Tensile Deformation

Crystallographic orientation related dynamic recrystallization behavior and its impact on texture development of high-temperature α phase in TiAl alloy

Texture Stability and Transition in an Accumulative Roll-Bonding-Processed Aluminum Single Crystal

Theoretical Analysis of Texture Evolution in Cold Rolling Process of Single Crystal Aluminum

Finite Element Analysis on the Effect of the Texture to the Crack Tip Plasticity in Aluminum Alloy

CPFEM simulations on grain rotation of γ-TiAl single crystal during plastic deformation

INVESTIGATION OF PLASTIC DEFORMATION BEHAVIOR ON COUPLING TWINNING OF POLYCRYSTAL TWIP STEEL