Abstract:In this study, SiC nanoparticles were added into matrix alloy through a combination of semisolid stirring and ultrasonic vibration while dynamic precipitation of second phases was obtained through multi-pass forging with varying temperatures. During single-pass forging of the present composite, as the deformation temperature increased, the extent of recrystallization increased, and grains were refined due to the inhibition effect of the increasing amount of dispersed SiC nanoparticles. A small amount of twins within the SiC nanoparticle dense zone could be found while the precipitated phases of Mg17Al12 in long strips and deformation bands with high density dislocations were formed in the particle sparse zone after single-pass forging at 350 °C. This indicated that the particle sparse zone was mainly deformed by dislocation slip while the nanoparticle dense zone may have been deformed by twinning. The yield strength and ultimate tensile strength of the composites were gradually enhanced through increasing the single-pass forging temperature from 300 °C to 400 °C, which demonstrated that initial high forging temperature contributed to the improvement of the mechanical properties. During multi-pass forging with varying temperatures, the grain size of the composite was gradually decreased while the grain size distribution tended to be uniform with reducing the deformation temperature and extending the forging passes. In addition, the amount of precipitated second phases was significantly increased compared with that after multi-pass forging under a constant temperature. The improvement in the yield strength of the developed composite was related to grain refinement strengthening and Orowan strengthening resulting from synergistical effect of the externally applied SiC nanoparticles and internally precipitated second phases.

Superplasticity and Sinter-Forging of Fine-Grained Si3N4-Si2N2O Composite

Superplasticity and sinter-forging of fine-grained Si3N 4-Si2N2O composite

Fabrication of Fine-Grained Si 3 N 4 -Si 2 N 2 O Composites by Sintering Amorphous Nano-Sized Silicon Nitride Powders

Superplastic Forging for Sialon-based Nanocomposite at Ultralow Temperature in the Electric Field

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Strengthening mechanism and anisotropy of mechanical properties of Si3N4p/Al-Mg-Si composites fabricated by sintering and extrusion

Hot-press Sintering and Superplastic Forming of Nano-Ceramics

Influence of Fabricated Process on Mechanical Properties of Porous Sic-Particle/Si3n4 Composites

Injection Molding of Ultra-Fine Si 3 N 4 Powder for Gas-Pressure Sintering

Influence of fabricated process on mechanical properties of porous SiC-particle/ Si3N4 composites

Fabrication and Properties of SiO2-BN-Si3N4 Composites

Development of SiC Nanoparticles and Second Phases Synergistically Reinforced Mg-Based Composites Processed by Multi-Pass Forging with Varying Temperatures

Fabrication and Mechanical Properties of Si3N4/SiC Nanocompoisites under Pressureless Sintering.

Mechanical properties and superplasticity of the Ni/Si3N4(W) nanocomposite fabricated by electrodeposition

Superplasticity of Multiphase Refractory Nb-16si-2fe in Situ Composite

Fabrication of continuously porous SiC–Si3N4 composite using SiC powder by extrusion process

Superplasticity of Nb-Si-Fe and TiAl Intermetallics Synthesized by Powder Metallurgy

The Effect of Si3N4 on Microstructure, Mechanical Properties and Oxidation Resistance of HfB2-based Composite

Fabrication and Mechanical Properties of Si3n4/Sic Nanocomposite with Pressureless Sintering and Sinter-Post-Hiping

Fabrication of silicon nitride with high thermal conductivity and flexural strength by hot‐pressing flowing sintering

High Temperature Mechanical Properties of Partially Sinter-Forged Porous Anisotropic Silicon Nitride