Abstract:Additively manufactured (AM) biodegradable porous iron-manganese (FeMn) alloys have recently been developed as promising bone-substituting biomaterials. However, their corrosion fatigue behavior has not yet been studied. Here, we present the first study on the corrosion fatigue behavior of an extrusion-based AM porous Fe35Mn alloy under cyclic loading in air and in the revised simulated body fluid (r-SBF), including the fatigue crack morphology and distribution in the porous structure. We hypothesized that the fatigue behavior of the architected AM Fe35Mn alloy would be strongly affected by the simultaneous biodegradation process. We defined the endurance limit as the maximum stress at which the scaffolds could undergo 3 million loading cycles without failure. The endurance limit of the scaffolds was determined to be 90 % of their yield strength in air, but only 60 % in r-SBF. No notable crack formation in the specimens tested in air was observed even after loading up to 90 % of their yield strength. As for the specimens tested in r-SBF, however, cracks formed in the specimens subjected to loads exceeding 60 % of their yield strength appeared to initiate on the periphery and propagate toward the internal struts. Altogether, the results show that the extrusion-based AM porous Fe35Mn alloy is capable of tolerating up to 60 % of its yield strength for up to 3 million cycles, which corresponds to 1.5 years of use of load-bearing implants subjected to repetitive gait cycles. The fatigue performance of the alloy thus further enhances its potential for trabecular bone substitution subjected to cyclic compressive loading. STATEMENT OF SIGNIFICANCE: Fatigue behavior of extrusion-based AM porous Fe35Mn alloy scaffolds in air and revised simulated body fluid was studied. The Fe35Mn alloy scaffolds endured 90 % of their yield strength for up to 3 × 10<sup>6</sup> loading cycles in air. Moreover, the scaffolds tolerated 3 × 10<sup>6</sup> loading cycles at 60 % of their yield strength in revised simulated body fluid. The Fe35Mn alloy scaffolds exhibited a capacity of withstanding 1.5-year physiological loading when used as bone implants.

Selective Laser Melted Fe-Mn Bone Scaffold: Microstructure, Corrosion Behavior and Cell Response

Regulation of Surface Micro-Nano Structure of Porous Fe-Mn Alloy and Evaluation on Its Biological Performance

A Novel Porous Fe/Fe-W Alloy Scaffold with A Double-Layer Structured Skeleton: Preparation, in Vitro Degradability and Biocompatibility

Microstructure, Mechanical Properties and Corrosion Behavior of Additively-Manufactured Fe–Mn Alloys

Microstructure and Corrosion Behavior of Iron Based Biocomposites Prepared by Laser Additive Manufacturing

Mechanical and Functional Properties of Fe–Mn–Si Biodegradable Alloys Fabricated by Laser Powder Bed Fusion: Effect of Heat Treatment

Galvanic Corrosion Induced by Heterogeneous Bimodal Grain Structures in Fe-Mn Implant

Accelerated biodegradation of Fe-30Mn-S biocomposite via preferential corrosion of secondary phase

Comparative Study of Pure Iron Manufactured by Selective Laser Melting, Laser Metal Deposition, and Casting Processes

Finite Element Simulation of Stainless Steel Porous Scaffolds for Selective Laser Melting (SLM) and Its Experimental Investigation

Mechanically Driving Supersaturated Fe–Mg Solid Solution for Bone Implant: Preparation, Solubility and Degradation

Dual Alloying Improves the Corrosion Resistance of Biodegradable Mg Alloys Prepared by Selective Laser Melting

Tribocorrosion Behavior of Additively-Manufactured Fe-Mn Alloys

FeMnCSi alloy for degradable pin implants: surface and in vitro characterization

Optimization of Structural and Processing Parameters for Selective Laser Melting of Porous 316L Bone Scaffolds

<i>In vitro</i> and 48 weeks <i>in vivo</i> performances of 3D printed porous Fe-30Mn biodegradable scaffolds

Mesoporous Carbon as Galvanic-Corrosion Activator Accelerates Fe Degradation

Cancellous-Bone-like Porous Iron Scaffold Coated with Strontium Incorporated Octacalcium Phosphate Nanowhiskers for Bone Regeneration

Optimising Degradation and Mechanical Performance of Additively Manufactured Biodegradable Fe–Mn Scaffolds Using Design Strategies Based on Triply Periodic Minimal Surfaces

Biodegradation-affected fatigue behavior of extrusion-based additively manufactured porous iron–manganese scaffolds

Mechanical and corrosion performance of biodegradable iron porous structures