Abstract:The automobile industry relies primarily on spot welding operations, particularly resistance spot welding (RSW). The performance and durability of the resistance spot-welded joints are significantly impacted by the welding quality outputs, such as the shear force, nugget diameter, failure mode, and the hardness of the welded joints. In light of this, the present study sought to determine how the aforementioned welding quality outputs of 0.5 and 1 mm thick austenitic stainless steel AISI 304 were affected by RSW parameters, such as welding current, welding time, pressure, holding time, squeezing time, and pulse welding. In order to guarantee precise evaluation and experimental analysis, it is essential that they are supported by a numerical model using an intelligent model. The primary objective of this research is to develop and enhance an intelligent model employing artificial neural network (ANN) models. This model aims to provide deeper knowledge of how the RSW parameters affect the quality of optimum joint behavior. The proposed neural network (NN) models were executed using different ANN structures with various training and transfer functions based on the feedforward backpropagation approach to find the optimal model. The performance of the ANN models was evaluated in accordance with validation metrics, like the mean squared error (MSE) and correlation coefficient (R2). Assessing the experimental findings revealed the maximum shear force and nugget diameter emerged to be 8.6 kN and 5.4 mm for the case of 1-1 mm, 3.298 kN and 4.1 mm for the case of 0.5-0.5 mm, and 4.031 kN and 4.9 mm for the case of 0.5-1 mm. Based on the results of the Pareto charts generated by the Minitab program, the most important parameter for the 1-1 mm case was the welding current; for the 0.5-0.5 mm case, it was pulse welding; and for the 0.5-1 mm case, it was holding time. When looking at the hardness results, it is clear that the nugget zone is much higher than the heat-affected zone (HZ) and base metal (BM) in all three cases. The ANN models showed that the one-output shear force model gave the best prediction, relating to the highest R and the lowest MSE compared to the one-output nugget diameter model and two-output structure. However, the Levenberg-Marquardt backpropagation (Trainlm) training function with the log sigmoid transfer function recorded the best prediction results of both ANN structures.

Modeling and Process Analysis of Resistance Spot Welded DP600 Joints Based on Regression Analysis

Numerical Prediction and Control of Deformation and Residual Stress in Double-Sided Arc Welding of Large Pressure Hull

Assessing the Residual Stresses in Dissimilar Welded Joint: Depth-Sensing Indentation Testing and Numerical Simulation

Numerical modeling from process to residual stress induced in resistance spot welding of DP980 steel

Influence of Material Model on Prediction Accuracy of Welding Residual Stress in an Austenitic Stainless Steel Multi-pass Butt-Welded Joint

Strength Prediction of Sheet to Tube Single Sided Resistance Spot Welding

Quantitative Interpretation of Dynamic Resistance Signal in Resistance Spot Welding

Process optimization of aluminum/steel resistance spot welding based on dynamic resistance analysis

Validated Multi-Physical Finite Element Modelling of the Spot Welding Process of the Advanced High Strength Steel DP1200HD

An experimental methodology to characterize load-based fracture models of third generation advanced high strength steel resistance spot welds

Advanced process characterization and machine learning-based correlations between interdiffusion layer and expulsion in spot welding

Artificial Neural Networks and Experimental Analysis of the Resistance Spot Welding Parameters Effect on the Welded Joint Quality of AISI 304

Measurement of Local Material Properties and Failure Analysis of Resistance Spot Welds of Advanced High-Strength Steel Sheets

Resistance spot welding of high-strength DP steel and nano/ultrafine-grained IF steel sheets

In Situ Observations of the Strain Competition Phenomenon in Aluminum Alloy Resistance Spot Welding Joints during Lap Shear Testing

Investigation on residual stress of EQ56 high strength steel butt weld

Predicting Welding Residual Stress of a Multi-pass P92 Steel Butt-Welded Joint with Consideration of Phase Transformation and Tempering Effect

Assessing Electrode Characteristics in Continuous Resistance Spot Welding of BH 340 Steel Based on Dynamic Resistance

Collaborative Simulation of Nugget Growth and Process Signals for Resistance Spot Welding

On Utilization Of Material Failure Criterion In Modeling Pull-Out Failure Of Spot-Welded Joints

Study on the Thermo-Effect of Nugget Growing in Single-Phase AC Resistance Spot Welding Based on the Calculation of Dynamic Resistance