Abstract:Abstract Metal magnesium is mainly produced from the calcined dolomite by the silicothermic production. However, in this process, the reduction temperature is higher while the reaction speed is slow, which results in higher energy consumption and serious environmental problems. In this paper, adding aluminum into the ferrosilicon reducing agent is expected to lower the reaction temperature so as to solve the problems above. The phase transition involved in the whole reduction process including with and without aluminum addition were investigated in details by theoretical calculation and experimental research. The influence of aluminum on the magnesium oxide reduction path was analysis to clarify the internal mechanism. The results show that aluminum added into the ferrosilicon would first react with magnesium oxide to form magnesium vapor and alumina under vacuum pressure of 10 Pa when the temperature rises to 720°C. Then, calcium aluminate would be formed by the reaction of aluminum oxide and calcium oxide. Once the temperature reaches 1150°C, silicon begins to reduce the magnesium oxide to create the silicon oxide that will finally react with calcium oxide to form calcium silicate. When the temperature rises above 1150°C, both the aluminum and silicon will participate in the reduction of magnesium oxide. In the process of heating up, the mixture of aluminum, ferrosilicon and calcined dolomite forms Mg 2 Al 4 Si 5 O 18 and Ca 3 Al 2 (OH) 12 phase with the components in calcined dolomite. Mg 2 Al 4 Si 5 O 18 and Ca 3 Al 2 (OH) 12 phase finally form Ca 12 Al 14 O 33 phase. The interaction between aluminum and ferrosilicon in the mixture is less; the mixture of aluminum and ferrosilicon first forms Al 3 FeSi 2 phase, and finally has the trend of forming Al 4.5 FeSi phase. There is a great difference between the phase transformation of aluminum in the mixture of aluminum, ferrosilicon and calcined dolomite and that of aluminum in the mixture of aluminum and ferrosilicon.

Aluminum-Silicon Alloys Prepared from High-Aluminum Fly Ash to Extract Magnesium from Serpentine

Research on New Thermal Reduction Process of Magnesium Preparation at Ordinary Pressure with Serpentine as Raw Material

Green and Efficient Utilization of Ferruginous Gibbsite Ore and Ferruginous Manganese Ore by Synergetic Carbothermic Co-Reduction–Magnetic Separation Process

Kinetic study of high-pressure acid leaching of Mg and Ni from serpentine

Extraction of Aluminum Hydroxide from Coal Fly Ash by Pre-Desilication and Calcination Methods

Fe-Si alloys production and alumina extraction from coal fly ash via the vacuum thermal reduction and alkaline leaching

Phase transformation involved in the reduction process of magnesium oxide in calcined dolomite by ferrosilicon with additive of aluminum

Alumina Extraction from Alumina Rich Fly Ash Generated from Inner-Mongolia Chinese Coal

Aluminum extraction technologies from high aluminum fly ash

Recovery of Mg from H2SO4 Leaching Solution of Serpentine to Precipitation of High-Purity Mg(OH)2 and 4MgCO3·Mg(OH)2·4H2O

Extraction of aluminum values from fly ash

Energy-efficient leaching process for preparation of aluminum sulfate and synergistic extraction of Li and Ga from circulating fluidized bed fly ash

Novel Efficient Reduction Route for Magnesium Production Using Silicothermic Process

Spinel Ferrite Transformation for an Efficient Fe Removal from Circulating Fluidized Bed Fly Ash by Carbothermal Reduction at a Low Temperature.

Experimental Study of Magnesium (Mg) Production by an Integrated Calcination and Silicothermic Reduction Short Process

Extraction of Aluminum from Coal Fly Ash Using Pressurized Sulfuric Acid Leaching with Emphasis on Optimization and Mechanism

Study on magnesium reduction process for air-cooled high magnesium-bearing blast furnace slag

An efficient and environmental friendly strategy for alumina extraction and Fe–Si alloys production from coal fly ash by combining vacuum thermal reduction, alkali dissolving, and magnetic separation

Rare earth element recovery and aluminum-rich residue production from high alumina fly ash by alkali pre-desilication enhance the mechanochemical extraction process