Abstract:Natural gas is an attractive fuel for internal combustion engines in light of its potential for reduced greenhouse gas and particulate emissions, and significant reserves. To facilitate natural gas use in compression ignition engines, pilot-ignited direct-injection natural gas combustion uses a small pilot injection of diesel to ignite a more significant direct injection of natural gas. Compared to modern diesel combustion, this strategy is a promising technology for the reduction of CO 2 emissions while retaining diesel-like efficiency without a significant CH 4 emission penalty. To further develop this technology, investigation of in-cylinder combustion processes is needed to identify the primary fuel conversion processes. The objective of this work was to provide a framework of conceptual understanding by identifying key processes in a typical pilot-ignited direct-injection natural gas combustion event and characterizing their sensitivity to fuel injection parameters. A parametric sweep of injection pressure, natural gas injection duration, and relative timing of the diesel pilot and natural gas injections was performed in an optically accessible 2 L single-cylinder engine. Combined heat release rate and OH*-chemiluminescence reaction zone analysis was used to demarcate the transition from ignition reactions to primary natural gas heat release. Five distinct combustion processes were identified: (1) pilot auto-ignition; (2) natural gas ignition; (3) rapid, distributed partially premixed natural gas combustion; (4) non-premixed combustion; and (5) late-cycle oxidation. While natural gas ignition was found to be insensitive to injection pressure, it was strongly affected by the time between pilot and natural gas injections. Reducing the relative injection timing from +8° to −6° resulted in the primary natural gas heat release transitioning from non-premixed, to distributed partially premixed, to stratified premixed flame propagation as a result of increasing natural gas premixing. The presented measurements and analysis serve to refine an initial conceptual model of the combustion process and lay the groundwork for future, more focused studies of pilot-ignited, direct-injection natural gas combustion.

Parametric investigation of pre-injection on the combustion, knocking and emissions behaviour of a large marine four-stroke dual-fuel engine

Implementation and Parameter Analysis of the Knock Phenomenon of a Marine Dual-Fuel Engine Based on a Two-Zone Combustion Model

Numerical investigation on knock characteristics and mechanism of large-bore natural gas dual-fuel marine engine

Impact of Pilot Injection on Combustion and Emission Characteristics of a Low-Speed Two-Stroke Marine Diesel Engine

Investigation on efficient and clean combustion pre-injection strategy of a diesel/methanol dual direct-injection marine engine under full load

A Numerical Investigation on the Effects of Intake Swirl and Mixture Stratification on Combustion Characteristics in a Natural-Gas/Diesel Dual-Fuel Marine Engine

Numerical Investigation of the Effect of Injection Timing on the In-Cylinder Activity of a Gasoline Direct Injection Engine

Parametric analysis of hydrogen two-stage direct-injection on combustion characteristics, knock propensity, and emissions formation in a rotary engine

Experimental investigation of knock control criterion considering power output loss for a PFI SI methanol marine engine

Numerical Investigations of Injection Timing Effects on a GDI Engine Performance: Part B, In-Cylinder Emission Formation and Oxidation Process

Research on the Ignition Strategy of Diesel Direct Injection Combined with Jet Flame on the Combustion Character of Natural Gas in a Dual-Fuel Marine Engine

Optimization of direct injection mixture formation for dual-fuel low speed marine engine using novel compound electric gas injection devices

Study on Characteristics Optimization of Combustion and Fuel Injection of Marine Diesel Engine

Numerical Study of the Effect of Direct-Injection Timing of Methanol and Excess Air Ratio on the Combustion Characteristics of a Marine Diesel-Methanol Dual-Fuel Engine

Experimental research on the effects of kerosene on the pre-injection spray characteristics and engine performance of dual-direct injection diesel Jet Controlled Compression Ignition mode

Statistical Quantification of Knock With Spark Ignition and Pre-Chamber Jet Ignition in a Light Duty Gasoline Engine

Parametric study of pilot-ignited direct-injection natural gas combustion in an optically accessible heavy-duty engine

Hydrogen injection optimization of a low-speed two-stroke marine hydrogen/diesel engine

Dual-Injection As a Knock Mitigation Strategy Using Pure Ethanol and Methanol

Effects of injection strategy on the knocking behavior of a pilot ignited direct injection natural gas engine

Impact of pilot diesel injection timing on performance and emission characteristics of marine natural gas/diesel dual-fuel engine