Abstract:Natural gas is an attractive fuel for internal combustion engines in light of its potential for reduced greenhouse gas and particulate emissions, and significant reserves. To facilitate natural gas use in compression ignition engines, pilot-ignited direct-injection natural gas combustion uses a small pilot injection of diesel to ignite a more significant direct injection of natural gas. Compared to modern diesel combustion, this strategy is a promising technology for the reduction of CO 2 emissions while retaining diesel-like efficiency without a significant CH 4 emission penalty. To further develop this technology, investigation of in-cylinder combustion processes is needed to identify the primary fuel conversion processes. The objective of this work was to provide a framework of conceptual understanding by identifying key processes in a typical pilot-ignited direct-injection natural gas combustion event and characterizing their sensitivity to fuel injection parameters. A parametric sweep of injection pressure, natural gas injection duration, and relative timing of the diesel pilot and natural gas injections was performed in an optically accessible 2 L single-cylinder engine. Combined heat release rate and OH*-chemiluminescence reaction zone analysis was used to demarcate the transition from ignition reactions to primary natural gas heat release. Five distinct combustion processes were identified: (1) pilot auto-ignition; (2) natural gas ignition; (3) rapid, distributed partially premixed natural gas combustion; (4) non-premixed combustion; and (5) late-cycle oxidation. While natural gas ignition was found to be insensitive to injection pressure, it was strongly affected by the time between pilot and natural gas injections. Reducing the relative injection timing from +8° to −6° resulted in the primary natural gas heat release transitioning from non-premixed, to distributed partially premixed, to stratified premixed flame propagation as a result of increasing natural gas premixing. The presented measurements and analysis serve to refine an initial conceptual model of the combustion process and lay the groundwork for future, more focused studies of pilot-ignited, direct-injection natural gas combustion.

Parametric study of pilot-ignited direct-injection natural gas combustion in an optically accessible heavy-duty engine

Optical and Numerical Investigations of Flame Propagation in a Heavy Duty Spark Ignited Natural Gas Engine

An Experimental Investigation of Early Flame Development in an Optical Spark Ignition Engine Fueled with Natural Gas

Flame Development Analysis in a Diesel Optical Engine Converted to Spark Ignition Natural Gas Operation

Analysis of Two-Stage Natural-Gas Lean Combustion Inside a Diesel Geometry

Experimental Setup of Combustion Visualization Inside a Heavy-Duty Diesel Engine Converted to Natural-Gas Spark-Ignition Operation

Effect of Bowl-in-Piston Chamber on the Combustion Process in a Stoichiometric Natural-Gas Spark-Ignition Engine

An Experimental Study of the Combustion Process in a Natural-Gas Spark-Ignition Engine

Multiple Combustion Stages Inside a Heavy-Duty Diesel Engine Retrofitted to Natural-Gas Spark-Ignition Operation

Effect of Spark Timing on the Combustion Stages Seen in a Heavy-Duty Compression-Ignition Engine Retrofitted to Natural Gas Spark-Ignition Operation

Methodology to Separate the Two Burn Stages of Natural-Gas Lean Premixed-Combustion Inside a Diesel Geometry

Two-Stage Lean-Burn Combustion Inside a Natural-Gas Spark-Ignition Engine with a Bowl-in-Piston Chamber

Methodology to Determine the Fast Burn Period Inside a Heavy-Duty Diesel Engine Converted to Natural Gas Lean-Burn Spark Ignition Operation

Observation of Flame Propagation in a Heavy-Duty Natural-Gas Lean Burn Spark-Ignition Engine

Experimental Investigation of a Heavy-Duty Compression-Ignition Engine Retrofitted to Natural Gas Spark-Ignition Operation

Conversion of a Heavy-Duty Diesel Engine to Natural-Gas Spark-Ignition Operation: Test Bench Development

Twin-Peak Heat Release Phenomenon Inside a Heavy-Duty Diesel Engine Retrofitted to Natural-Gas Spark Ignition

Investigation of Multistage Combustion Inside a Heavy-Duty Natural-Gas Spark-Ignition Engine Using Three-Dimensional Computational Fluid Dynamics Simulations and the Wiebe-Function Combustion Model

Combustion Process and Emissions of A Heavy-Duty Engine Fueled with Directly Injected Natural Gas and Pilot Diesel

Study on the ignitability of a high-pressure direct-injected methane jet using a diesel pilot, a glow-plug, and a pre-chamber

Effects and mechanism of pilot diesel injection strategies on combustion and emissions of natural gas engine