Abstract:Magnesium‐lithium (MgLi) alloys have been widely used in various engineering fields due to their ultra-light characteristics. The strengthening of MgLi alloys is one of the key factors determining its application and has received extensive attention. In this work, the as-cast ultralight and high strength Mg-10Li-3Al-3Zn-xY (x = 0, 0.5 and 1.0, wt%) alloys with a density of only 1.52 g/cm3 were prepared via vacuum induction melting. The effects of rare earth element yttrium (Y) on the microstructure and mechanical properties of the MgLi alloy system were investigated. The results indicated that the microstructures of all the alloys mainly consisted of α-Mg, β-Li, AlLi, and MgLi2Al phases. The spherical AlLi phase was distributed inside the α-Mg and β-Li matrix. Part of the petal-like MgLi2Al phase was distributed in the interior of β-Li, and the rest grew along the grain boundaries as long strips. With the addition of Y, Al2Y phase formed with sharp edges and regular shapes. The Al2Y phase was mainly distributed inside the α-Mg phase and along the grain boundaries. Meanwhile, the amount of AlLi phase inside the α-Mg phase gradually decreased. The presence of nano-scale lath-shape MgLiZn phase in the β-Li matrix was observed in the HAADF map of the 0.5Y alloy. The continuous growth of MgLi2Al phase at the grain boundaries weakened its strength. As a consequence, it eventually led to intergranular fracture of the alloy. The 0.5Y alloy showed the highest tensile strength, up to ~244 MPa, and the yield strength was 60.5% higher than that of the 0Y alloy. Solid solution strengthening, precipitate strengthening and grain refinement were thus considered as the primary strengthening mechanisms caused by the addition of Y into the Mg-10Li-3Al-3Zn alloy.

Microstructure and Mechanical Properties of As-Cast Mg-Sn-Zn-Y Alloys

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Microstructure and Mechanical Properties of Mg-Xy-1.5mm-0.4zr Alloys

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

Improvement of Mechanical Properties and Corrosion Resistance of As‐Extruded Mg–2Zn–2Al–0.3Mn Alloy Through Y Addition

Effect of Y content on microstructure evolution and tensile properties of Mg-8Li-3Al-2Sn-xY alloys

Microstructure and mechanical properties of cast Mg-6Gd–Zr alloy with different Y addition

Microstructure and mechanical properties of as-cast ultralight and high strength Mg-10Li-3Al-3Zn-xY alloy with multi-precipitates

Effects of Y on Microstructure and Mechanical Properties of Extruded Mg-5Al-1Ca Magnesium Alloys

Effect of Yttrium Addition on Microstructure and Mechanical Properties of Sr-Modified Low-Si Cast Aluminum Alloy

Microstructure and Mechanical Properties of Extruded Mg-Zn-Nd-Y-Zr-Ca Alloy

Investigations on Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn-Zr-Nd Alloy

Achieving advanced elevated-temperature strength by tailoring precipitates in Mg-Sn-Y alloys

Influence of Al Addition on the Microstructure and Mechanical Properties of Mg-Zn-Sn-Mn-Ca Alloys

Simulation on Microstructure Evolution and Mechanical Properties of Mg−Y Alloys: Effect of Trace Y

Role of Y on the microstructure and mechanical properties of Mg-Gd-Zr alloy

Effects of yttrium additions on microstructures and mechanical properties of cast Al-Cu-Mg-Ag alloys

Microstructure, generation of intermetallic compounds and mechanical strengthening mechanism of as-cast Mg–4Y–xZn alloys

Effect of combined addition of Zr, Ti and Y on microstructure and tensile properties of an Al-Zn-Mg-Cu alloy

Effect of Al addition on the grain refinement and mechanical properties of as-cast Mg–5Y–4Sm alloys

Effects of Zn Addition on the Microstructure, Tensile Properties and Formability of As-Extruded Mg-1Sn-0.5Ca Alloy