Abstract:Herein, copper indium diselenide ternary (CuInSe2) thin film has been deposited on Indium Tin Oxide (ITO) coated glass substrate by electrochemical deposition technique with different potential and pH solutions. CuInSe2 thin films were deposited by one-step electrodeposition before post-depot selenization at 450 °C for 30 min. The effect of potential and pH on the structural and optical properties of CuInSe thin film have been studied using X-ray diffraction (XRD), Scanning electron microscopy (SEM), and UV-Visible spectrometer. According to the X-ray diffraction (XRD) measurements, it was observed that all samples exhibit prominent reflections (112), (204/220), and (312/116) of tetragonal CuInSe2. The films electrodeposited at -0.8 V potential shows growth and peak values increasing in the (204/220) crystal direction within a pH range of 2.2, whereas the films electrodeposited at pH 2.6 tend to favor an increase in (112) peaks. We also noticed an improvement in surface morphology and adherent of CuInSe2 thin films electrodeposited at -0.8 V applied potential from the solution having pH 2.6. The band gaps of samples electrodeposited at -0.8V potentials from pH 2.6, 2.4, and 2.2 solutions were 1.15 eV, 1.25 eV, and 1.21 eV, respectively. As part of our investigation, we used a Solar Cell capacitance simulator (SCAPS) to perform our electrodeposited films. The most effective Power conversion efficiency (PCE) was obtained for thin films electrodeposited at -0.8 V within the solution having pH 2.4.

Structure and Photovoltaic Characteristics of CuInSe2 Thin Films Prepared by Pulse-Reverse Electrodeposition and Selenization Process

Preparation and characterization of CuInSe2 thin films derived by electrodeposition process for solar cells

Preparation and Characterization of Cuins2 Thin Films for Solar Cells by Chemical Bath Deposition

Preparation and characterization of Cu2ZnSnSe4 thin films by selenization of electrodeposited metal precursors

Structural properties of CuInSe2 films prepared by selenization of metallic precursors on MoNx film substrates

Preparation and Characterization of Electrodeposited-Annealed CuInSe2 Thin Films for Solar Cells

P-type CuInSe 2 Thin Films Prepared by Selenization of One-Step Electrodeposited Precursors

Research on CuInS2 Thin Films Prepared by One-step Electrodeposition

Preparation Of Cu(In1-Xalx)Se-2 Thin Films By Sol-Gel Method

Optimization of Fabrication Parameters of CuInSe2 Thin Films by DC-Magnetron Sputtering the Metal Precursor Followed by Selenization

Investigation of CuIn1-xAlxSe2 Thin Film for Solar Cells Prepared by a Selenization Process

Growth of copper indium diselenide ternary thin films (CuInSe2) for solar cells: Optimization of electrodeposition potential and pH parameters

Preparation of Cu(In 1−x Al x )Se 2 thin films by sol-gel method

Preparation of Cu(In1−xAlx)Se2 thin films by sol-gel method

Reactive Close-Spaced Sublimation Processed CuSbSe2 Thin Films and Their Photovoltaic Application

Thin-Film Solar Cells Based on Selenized CuSbS2 Absorber

The Cu 2ZnSnSe 4 thin films solar cells synthesized by electrodeposition route

Pulse Selenization in Cu(In,Ga)Se 2 Solar Cells: A Promising Approach to Achieve High Efficiency by Electrodeposition

Preparation of CuInSe2 thin films by pulsed laser deposition the Cu–In alloy precursor and vacuum selenization

Influence Of Annealing Conditions On The Structure And Compositions Of Electrodeposited Cuinse2 Films

Fundamental studies of CuInSe_2 thin films based solar cells