Abstract:"In research and development, the use of model-based methods has been established widely. In spite of the required costs and time for modelling and parameterization, the models become applicable in many steps of the design process from concept studies until parameter optimization. Particularly, during the early phase of the development of products or functions, it is necessary to keep time and cost efforts as low as possible without significantly reducing the quality of the simulation results. For the development of vehicle dynamic controls, the quality of the used models depends highly on the modelling of the wheel-road contact. Due to the reduced parameterization and calculation effort, mathematical-empirical or semi-physical approaches as well as flexible belt-ring models are preferred to simulate severe driving manoeuvres such as full braking with ABS intervention or the ISO 3888 double lane-change. The determination of the model parameters is carried out using special tire test rigs in which the tire and rim are clamped. Due to the complex experimental setup and the required infrastructure, these tests are very cost-intensive. In driving tests with real vehicle, commercially available wheel force transducers are used today. By means of force measuring elements, which are usually attached to an especially manufactured and split rim body, the transmitted forces and moments are determined while driving. A high-resolution angle sensor detects the rotation angle and the angular velocity of the wheel in order to transform the measured quantities (forces and torque at the wheel) from the rotating to the vehicle related coordinate system. At the beginning of the paper, established concepts of tire test rigs for determining the parameters of mathematical-empirical tire models will be summarized and compared with the proposed usage of a wheel force transducer in real-driving tests. This will include an estimation of the boundary conditions and the reproducibility of the measurements as well as influencing factors on the force transmission. Subsequently, the test equipment and driving manoeuvres that were carried out with the test vehicle are presented. In addition to the wheel force transducer, a 2-axis optical speed sensor is added to the test setup. Using the measured vehicle velocity and the measured wheel speed the tire slip can be calculated now. The measurement data is partly used for parameter identification of two simplified tire models according to PACEJKA and BURCKHARDT, which describe the steady-state friction coefficient slip characteristic. Since these are nonlinear tire models, a non-linear least squares algorithm is used as the mathematical optimization method. The measurement data, which was not used for the parameterization, are applied in the subsequent validation of the tire model. On the basis of the obtained results a statement about the usability of a parameterized tire model based on measurements with a wheel force transducer is made and possible extensions and suggestions for improvement are derived."

Tire-Ground Interaction Force Model and Its Parameter Identification Considering Tire Geometry and Pressure

Finite Element Modeling of Interaction Between Non-Pneumatic Mechanical Elastic Wheel and Soil

Static Tire Properties Analysis and Static Parameters Derivation to Characterising Tire Model Using Experimental and Numerical Solutions

Parameter identification for a LuGre model based on steady-state tire conditions

A Hybrid Physical-Dynamic Tire/Road Friction Model

Research on tire model parameter identification strategy based on CDTire/3D

Research on simplified tire finite element modeling and simulation method

Tire–Pavement Contact Stress with 3D Finite-Element Model—Part 1: Semi-Steel Radial Tires on Light Vehicles

FEM tire model oriented to virtual experiment of off-road vehicle trafficability

Modeling and Validation of a Passenger Car Tire Using Finite Element Analysis

A Tire-Pavement Contact Model Derived from Measured Tire Characteristics

A novel theoretical model of tire in-plane dynamics on uneven roads and its experimental validation

Parameter Identification of mathematical-empirical Tire Models using Measurement Data of a Wheel Force Transducer

Static Tire/Road Stick–Slip Interactions: Analysis and Experiments

Analysis on Polygonal Wear of Automotive Tire of Lateral-vertical Force Coupling Model

Research of FE Tire Model Oriented to Virtual Experiment of Off-Road Vehicle Trafficability

Tread's longitudinal vibration modeling and analysis for attachment characteristics of tire

Analytical model of tire rolling resistance based on elastic hysteresis theory

PARAMETER CALIBRATION FOR THE DISCRETE ELEMENT SIMULATION OF TIRE-SOIL INTERACTION

A Hybrid Physical and Data-Driven Framework for Improving Tire Force Calculation Accuracy

A Universal Approach to Tire Forces Estimation by Accelerometer-Based Intelligent Tire: Analytical Model and Experimental Validation