Engineering A Membrane Based Air Cathode for Microbial Fuel Cells Via Hot Pressing and Using Multi-Catalyst Layer Stacking

Wulin Yang,Bruce E. Logan

DOI: https://doi.org/10.1039/c6ew00098c

2016-01-01

Environmental Science Water Research & Technology

Abstract:Microbial fuel cell (MFC) cathodes must have high performance and be resistant to water leakage.

What problem does this paper attempt to address?

Ion Exchange Membrane Cathodes For Scalable Microbial Fuel Cells

YI Z UO,S HAOAN C HENG,BRUCE E. L OGAN

DOI: https://doi.org/10.1021/es801055r

IF: 11.4

2008-01-01

Environmental Science & Technology

Abstract:One of the main challenges for using microbial fuel cells (MFCs) is developing materials and architectures that are economical and generate high power densities. The performance of two cathodes constructed from two low-cost anion (AEM) and cation (CEM) exchange membranes was compared to that achieved using an ultrafiltration (UF) cathode, when the membranes were made electrically conductive using graphite paint and a nonprecious metal catalyst (CoTMPP). The best performance in single-chamber MFCs using graphite fiber brush anodes was achieved using an AEM cathode with the conductive coating facing the solution, at a catalyst loading of 0.5 mg/cm(2) CoTMPP. The maximum power density was 449 mW/m(2) (normalized to the projected cathode surface area) or 13.1 W/m(3) (total reactor volume), with a Coulombic efficiency up to 70% in a 50 mM phosphate buffer solution (PBS) using acetate. Decreasing the CoTMPP loading by 40-80% reduced power by 28-56%, with only 16% of the power (72 mW/m(2)) generated using an AEM cathode lacking a catalyst. Using a current collector (a stainless steel mesh) pressed against the inside surface of the AEM cathode and 200 mM PBS, the maximum power produced was further increased to 728 mW/m(2) (21.2 W/m(3)). The use of AEM cathodes and brush anodes provides comparable performance to similar systems that use materials costing nearly an order of magnitude more (carbon paper electrodes) and thus represent more useful materials for reducing the costs of MFCs for wastewater treatment applications.
Pressurized Air Cathodes for Enhanced Stability and Power Generation by Microbial Fuel Cells

Weihua He,Wulin Yang,Yushi Tian,Xiuping Zhu,Jia Liu,Yujie Feng,Bruce E. Logan

DOI: https://doi.org/10.1016/j.jpowsour.2016.09.112

IF: 9.2

2016-01-01

Journal of Power Sources

Abstract:Large differences between the water and air pressure in microbial fuel cells (MFCs) can deform and damage cathodes. To avoid deformation, the cathode air pressure was controlled to balance pressure differences between the air and water. Raising the air pressures from 0 to 10 kPa at a set cathode potential of -0.3 V (versus Ag/AgCl) enhanced cathode performance by 17%, but pressures >= 25 kPa decreased current and resulted in air leakage into the solution. Matching the air pressure with the water pressure avoided cathode deformation and improved performance. The maximum power density increased by 15%, from 1070 +/- 20 to 1230 +/- 70 mW m(-2), with balanced air and water pressures of 10 -25 kPa. Oxygen partial pressures >= 12.5 kPa in the cathode compartment maintained the oxygen reduction rate to be within 92 +/- 1% of that in ambient air. The use of pressurized air flow through the cathode compartments can enable closer spacing of the cathodes compared to passive gas transfer systems, which could make the reactor design more compact. The energy cost of pressurizing the cathodes was estimated to be smaller than the increase in power that resulted from the use of pressurized cathodes. (C) 2016 Elsevier B.V. All rights reserved.
Single-Step Fabrication Using A Phase Inversion Method of Poly(Vinylidene Fluoride) (pvdf) Activated Carbon Air Cathodes for Microbial Fuel Cells

Wulin Yang,Weihua He,Fang Zhang,Michael A. Hickner,Bruce E. Logan

DOI: https://doi.org/10.1021/ez5002769

IF: 11.558

2014-01-01

Environmental Science & Technology Letters

Abstract:Air cathodes used in microbial fuel cells (MFCs) need to have high catalytic activity for oxygen reduction, but they must also be easy to manufacture, inexpensive, and watertight. A simple one-step, phase inversion process was used here to construct an inexpensive MFC cathode using a poly(vinylidene fluoride) (PVDF) binder and an activated carbon catalyst. The phase inversion process enabled cathode preparation at room temperatures, without, the need for additional heat treatment, and it produced for the first time a cathode that did not require a separate diffusion layer to prevent water leakage. MFCs using this new type of cathode produced a maximum power density of 1470 +/- 50 mW m(-2) with acetate as a substrate, and 230 +/- 10 mW m(-2) with domestic wastewater. These power densities were similar to those obtained using cathodes made using more expensive materials or more complex procedures, such as cathodes with a polytetrafluoroethylene (PTFE) binder and a poly(dimethylsiloxane) (PDMS) diffusion layer, or a Pt catalyst. Even though the PVDF cathodes did not have a diffusion layer, they withstood up to 1.22 +/- 0.04 m of water head (similar to 12 kPa) without leakage, compared to 0.18 +/- 0.02 m for cathodes made using PTFE binder and PDMS diffusion layer. The cost of PVDF and activated carbon ($3 m(-2)) was less than that of the stainless steel mesh current collector ($12 m(-2)). PVDF-based AC cathodes therefore are inexpensive, have excellent performance in terms of power and water leakage, and they can be easily manufactured using a single phase inversion process at room temperature.
Power Generation by Packed-Bed Air-Cathode Microbial Fuel Cells

Xiaoyuan Zhang,Juan Shi,Peng Liang,Jincheng Wei,Xia Huang,Chuanyi Zhang,Bruce E. Logan

DOI: https://doi.org/10.1016/j.biortech.2013.05.014

IF: 11.4

2013-01-01

Bioresource Technology

Abstract:Catalysts and catalyst binders are significant portions of the cost of microbial fuel cell (MFC) cathodes. Many materials have been tested as aqueous cathodes, but air-cathodes are needed to avoid energy demands for water aeration. Packed-bed air-cathodes were constructed without expensive binders or diffusion layers using four inexpensive carbon-based materials. Cathodes made from activated carbon produced the largest maximum power density of 676 +/- 93 mW/m(2), followed by semi-coke (376 +/- 47 mW/m(2)), graphite (122 +/- 14 mW/m(2)) and carbon felt (60 +/- 43 mW/m(2)). Increasing the mass of activated carbon and semi-coke from 5 to >= 15 g significantly reduced power generation because of a reduction in oxygen transfer due to a thicker water layer in the cathode (similar to 3 or similar to 6 cm). These results indicate that a thin packed layer of activated carbon or semi-coke can be used to make inexpensive air-cathodes for MFCs. (C) 2013 Elsevier Ltd. All rights reserved.
Tubular Membrane Cathodes for Scalable Power Generation in Microbial Fuel Cells.

Yi Zuo,Shaoan Cheng,Doug Call,Bruce E. Logan

DOI: https://doi.org/10.1021/es0627601

IF: 11.4

2007-01-01

Environmental Science & Technology

Abstract:One of the greatest challenges for using microbial fuel cells (MFCs) for wastewater treatment is creating a scalable architecture that provides large surface areas for oxygen reduction at the cathode and bacteria growth on the anode. We demonstrate here a scalable cathode concept by showing that a tubular ultrafiltration membrane with a conductive graphite coating and a nonprecious metal catalyst (CoTMPP) can be used to produce power in an MFC. Using a carbon paper anode (surface area Aan = 7 cm2, surface area per reactor volume Aan,s = 25 m2/m3), an MFC with two 3-cm tube cathodes (Acat = 27 cm2, Acat,s = 84 m2/m3) generated up to 8.8 W/m3 (403 mW/m2) using glucose [0.8 g/L in a 50 mM phosphate buffer solution (PBS)], which was only slightly less than that produced using a carbon paper cathode with a Pt catalyst (9.9 W/m3, 394 mW/m2; Acat= 7 cm2, Acat,s= 25 m2/m3). Coulombic efficiencies (CEs) with carbon paper anodes were 25-40% with tube cathodes (CoTMPP), compared to 7-19% with a carbon paper cathode. When a high-surface-area graphite brush anode was used (Aan = 2235 cm2, Aan,s = 7700 m2/m3) with two tube cathodes placed inside the reactor (Acat = 27 cm2, Acas, = 93 m2/m3), the MFC produced 17.7 W/m3 with a CE = 70-74% (200 mM PBS). Further increases in the surface area of the tube cathodes to 54 cm2 (120 m2/m3) increased the total power output (from 0.51 to 0.83 mW), but the increase in volume resulted in a constant volumetric power density (approximately 18 W/m3). These results demonstrate that an MFC design using tubular cathodes coated with nonprecious metal catalysts, and brush anodes, is a promising architecture that is intrinsically scalable for creating larger systems. Further increases in power output will be possible through the development of cathodes with lower internal resistances.
Combined Carbon Mesh and Small Graphite Fiber Brush Anodes to Enhance and Stabilize Power Generation in Microbial Fuel Cells Treating Domestic Wastewater

Shijia Wu,Weihua He,Wulin Yang,Yaoli Ye,Xia Huang,Bruce E. Logan

DOI: https://doi.org/10.1016/j.jpowsour.2017.01.041

IF: 9.2

2017-01-01

Journal of Power Sources

Abstract:Microbial fuel cells (MFCs) need to have a compact architecture, but power generation using low strength domestic wastewater is unstable for closely-spaced electrode designs using- thin anodes (flat mesh or small diameter graphite fiber brushes) due to oxygen crossover from the cathode. A composite anode configuration was developed to improve performance, by joining the mesh and brushes together, with the mesh used to block oxygen crossover to the brushes, and the brushes used to stabilize mesh potentials. In small, fed-batch MFCs (28 mL), the composite anode produced 20% higher power densities than MFCs using only brushes, and 150% power densities compared to carbon mesh anodes. In continuous flow tests at short hydraulic retention times (HRTs, 2 or 4 h) using larger MFCs (100 mL), composite anodes had stable performance, while brush anode MFCs exhibited power overshoot in polarization tests. Both configurations exhibited power overshoot at a longer HRT of 8 h due to lower effluent CODs. The use of composite anodes reduced biomass growth on the cathode (1.9 +/- 0.2 mg) compared to only brushes (3.1 +/- 0.3 mg), and increased coulombic efficiencies, demonstrating that they successfully reduced oxygen contamination of the anode and the bio-fouling of cathode. (C) 2017 Elsevier B.V. All rights reserved.
Defect Free Rolling Phase Inversion Activated Carbon Air Cathodes for Scale-Up Electrochemical Applications

Kexin Yi,Wulin Yang,Bruce E. Logan

DOI: https://doi.org/10.1016/j.cej.2022.140411

IF: 15.1

2023-01-01

Chemical Engineering Journal

Abstract:Scalable production of air cathodes is crucial for applying electrochemical technologies in practical water treatment applications. However, existing fabrication procedures of air cathodes for microbial fuel cells (MFCs) are either complicated or not sufficiently waterproof for larger-scale processes. In this study, an easily imple-mented low-pressure rolling phase inversion method was developed for preparing scalable, waterproof activated carbon air cathodes. An aminated PVDF (NH2-PVDF) membrane was synthesized as a new gas diffusion layer (GDL) to avoid defect formation from contacting organic solvent during cathode fabrication. The cathode was easily enlarged to 1000 cm(2) with a high pressure resistance of 13 +/- 0.7 m H2O height (similar to 137 kPa), exceeding the waterproof capability of previously reported air cathodes. The electrochemical performance of the fabricated air cathode was not affected by the additional membrane. MFCs with the NH2-PVDF cathodes produced a maximum power density of 1010 +/- 40 mW m(-2), consistent with literature values. The cathode was used to generate H2O2 at a rate of 420 +/- 40 mg L-1 h(-1) (25 mA cm(-2)), and nickel catalyst modification further increased the rate to 760 +/- 60 mg L-1 h(-1) (25 mA cm(-2)). Overall, the highly waterproof rolling phase inversion activated carbon air cathodes showed great promise for scaling up biotic and abiotic electrochemical systems for practical applications.
Air-cathode preparation with activated carbon as catalyst, PTFE as binder and nickel foam as current collector for microbial fuel cells.

Shaoan Cheng,Jiancheng Wu

DOI: https://doi.org/10.1016/j.bioelechem.2013.03.001

IF: 5.76

2013-01-01

Bioelectrochemistry

Abstract:A cathode is a critical factor that limits the practical application of microbial fuel cells (MFCs) in terms of cost and power generation. To develop a cost-effective cathode, we investigate a cathode preparation technique using nickel foam as a current collector, activated carbon as a catalyst and PTFE as a binder. The effects of the type and loading of conductive carbon, the type and loading of activated carbon, and PTFE loading on cathode performance are systematically studied by linear sweep voltammetry (LSV). The nickel foam cathode MFC produces a power density of 1190±50mWm−2, comparable with 1320mWm−2 from a typical carbon cloth Pt cathode MFC. However, the cost of a nickel foam activated carbon cathode is 1/30 of that of carbon cloth Pt cathode. The results indicate that a nickel foam cathode could be used in scaling up the MFC system.
Microbial Fuel Cell Cathodes with Poly(dimethylsiloxane) Diffusion Layers Constructed Around Stainless Steel Mesh Current Collectors

Fang Zhang,Tomonori Saito,Shaoan Cheng,Michael A. Hickner,Bruce E. Logan

DOI: https://doi.org/10.1021/es903009d

2010-01-01

Abstract:A new and simplified approach for making cathodes for microbial fuel cells (MFCs) was developed by using metal mesh current collectors and inexpensive polymer/carbon diffusion layers (DLs). Rather than adding a current collector to a cathode material such as carbon cloth, we constructed the cathode around the metal mesh itself, thereby avoiding the need for the carbon cloth or other supporting material. A base layer of poly(dimethylsiloxane) (PDMS) and carbon black was applied to the air-side of a stainless steel mesh, and Pt on carbon black with Nafion binder was applied to the solution-side as catalyst for oxygen reduction. The PDMS prevented water leakage and functioned as a DL by limiting oxygen transfer through the cathode and improving coulombic efficiency. PDMS is hydrophobic, stable, and less expensive than other DL materials, such as PTFE, that are commonly applied to air cathodes. Multiple PDMS/carbon layers were applied in order to optimize the performance of the cathode. Two PDMS/carbon layers achieved the highest maximum power density of 1610 +/- 56 mW/m(2) (normalized to cathode projected surface area; 47.0 +/- 1.6 W/m(3) based on liquid volume). This power output was comparable to the best result of 1635 +/- 62 mW/m(2) obtained using carbon cloth with three PDMS/carbon layers and a Pt catalyst. The coulombic efficiency of the mesh cathodes reached more than 80%, and was much higher than the maximum of 57% obtained with carbon cloth. These findings demonstrate that cathodes can be constructed around metal mesh materials such as stainless steel, and that an inexpensive coating of PDMS can prevent water leakage and lead to improved coulombic efficiencies.
Immobilization of a Metal-Nitrogen-Carbon Catalyst on Activated Carbon with Enhanced Cathode Performance in Microbial Fuel Cells.

Wulin Yang,Bruce E. Logan

DOI: https://doi.org/10.1002/cssc.201600573

IF: 8.4

2016-01-01

ChemSusChem

Abstract:Applications of microbial fuel cells (MFCs) are limited in part by low power densities mainly due to cathode performance. Successful immobilization of an Fe-N-C co-catalyst on activated carbon (Fe-N-C/AC) improved the oxygen reduction reaction to nearly a four-electron transfer, compared to a twoelectron transfer achieved using AC. With acetate as the fuel, the maximum power density was 4.7±0.2 W m(-2) , which is higher than any previous report for an air-cathode MFC. With domestic wastewater as a fuel, MFCs with the Fe-N-C/AC cathode produced up to 0.8±0.03 W m(-2) , which was twice that obtained with a Pt-catalyzed cathode. The use of this Fe-N-C/AC catalyst can therefore substantially increase power production, and enable broader applications of MFCs for renewable electricity generation using waste materials.
Scalable air cathode microbial fuel cells using glass fiber separators, plastic mesh supporters, and graphite fiber brush anodes.

Xiaoyuan Zhang,Shaoan Cheng,Peng Liang,Xia Huang,Bruce E Logan

DOI: https://doi.org/10.1016/j.biortech.2010.05.090

IF: 11.4

2011-01-01

Bioresource Technology

Abstract:The combined use of brush anodes and glass fiber (GF1) separators, and plastic mesh supporters were used here for the first time to create a scalable microbial fuel cell architecture. Separators prevented short circuiting of closely-spaced electrodes, and cathode supporters were used to avoid water gaps between the separator and cathode that can reduce power production. The maximum power density with a separator and supporter and a single cathode was 75±1W/m3. Removing the separator decreased power by 8%. Adding a second cathode increased power to 154±1W/m3. Current was increased by connecting two MFCs connected in parallel. These results show that brush anodes, combined with a glass fiber separator and a plastic mesh supporter, produce a useful MFC architecture that is inherently scalable due to good insulation between the electrodes and a compact architecture.
Microalgae hydrogel-derived monolithicfree-standing air cathode for microbial fuel cells: Tailoring the macroporous structure for enhanced bioelectricity generation

Jun Li,Yingying Dong,Linbin Hu,Yudong Zhang,Qian Fu,Liang Zhang,Xun Zhu,Qiang Liao

DOI: https://doi.org/10.1016/j.rser.2021.111773

IF: 16.799

2022-01-01

Renewable and Sustainable Energy Reviews

Abstract:A high-performance and cost-effective cathode is highly desirable for the practical implementation of microbial fuel cell (MFC) technology, used for renewable energy recovery from wastewater. In this study, a monolithic, free-standing air cathode for MFCs is fabricated through a sol-gel-based route. Chlorella pyrenoidosa (CP) is selected as the catalyst precursor, polyacrylonitrile fiber as the precursor for the conductive and supporting skeleton, and deionized water as the solvent and pore former. Agar is also used as the gelling agent to facilitate the formation of 3D porous networks inside the cathodes. By systematically tailoring the porosity of the tubular air cathodes by varying the water content in the CP agar composite hydrogel, the mechanical strength and electrical conductivity of the cathode is optimized. Moreover, this fabrication process leads to abundant active sites for the oxygen reduction reaction and an interconnected hierarchical porous structure with separated transport paths for air supply and ion transfer. The tubular air cathode can be directly employed as an MFC cathode without the use of a polymer binder or other modifications. The MFC delivers a maximum power density of 106.3 ± 5.9 W m- 3, which is approximately 33% higher than that with a converntional Pt/C cathode (79.8 ± 4.1 W m- 3). This work therefore offers a promising new route for recovering bioelectricity from wastewater based on MFCs.

energy & fuels,green & sustainable science & technology
Cathodic Biofouling Control by Microbial Separators in Air-Breathing Microbial Fuel Cells

Chao Li,Kexin Yi,Shaogang Hu,Wulin Yang

DOI: https://doi.org/10.1016/j.ese.2023.100251

IF: 9.371

2023-01-01

Environmental Science and Ecotechnology

Abstract:Microbial fuel cells (MFCs) incorporating air-breathing cathodes have emerged as a promising ecofriendly wastewater treatment technology capable of operating on an energy-free basis. However, the inevitable biofouling of these devices rapidly decreases cathodic catalytic activity and also reduces the stability of MFCs during long-term operation. The present work developed a novel microbial separator for use in air-breathing MFCs that protects cathodic catalytic activity. In these modified devices, microbes preferentially grow on the microbial separator rather than the cathodic surface such that biofouling is prevented. Trials showed that this concept provided low charge transfer and mass diffusion resistance values during the cathodic oxygen reduction reaction of 4.6 +/- 1.3 and 17.3 +/- 6.8 U, respectively, after prolonged operation. The maximum power density was found to be stable at 1.06 +/- 0.07 W m-2 throughout a long-term test and the chemical oxygen demand removal efficiency was increased to 92% compared with a value of 83% for MFCs exhibiting serious biofouling. In addition, a cathode combined with a microbial separator demonstrated less cross-cathode diffusion of oxygen to the anolyte. This effect indirectly induced the growth of electroactive bacteria and produced higher currents in air-breathing MFCs. Most importantly, the present microbial separator concept enhances both the lifespan and economics of air-breathing MFCs by removing the need to replace or regenerate the cathode during longterm operation. These results indicate that the installation of a microbial separator is an effective means of stabilizing power generation and ensuring the cost-effective performance of air-breathing MFCs intended for future industrial applications.(c) 2023 The Authors. Published by Elsevier B.V. on behalf of Chinese Society for Environmental Sciences, Harbin Institute of Technology, Chinese Research Academy of Environmental Sciences. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/).
Power Generation Using an Activated Carbon and Metal Mesh Cathode in A Microbial Fuel Cell

Fang Zhang,Shaoan Cheng,Deepak Pant,Gilbert Van Bogaert,Bruce E. Logan

DOI: https://doi.org/10.1016/j.elecom.2009.09.024

IF: 5.443

2009-01-01

Electrochemistry Communications

Abstract:An inexpensive activated carbon (AC) air cathode was developed as an alternative to a platinum-catalyzed electrode for oxygen reduction in a microbial fuel cell (MFC). AC was cold-pressed with a polytetrafluoroethylene (PTFE) binder to form the cathode around a Ni mesh current collector. This cathode construction avoided the need for carbon cloth or a metal catalyst, and produced a cathode with high activity for oxygen reduction at typical MFC current densities. Tests with the AC cathode produced a maximum power density of 1220mW/m2 (normalized to cathode projected surface area; 36W/m3 based on liquid volume) compared to 1060mW/m2 obtained by Pt catalyzed carbon cloth cathode. The Coulombic efficiency ranged from 15% to 55%. These findings show that AC is a cost-effective material for achieving useful rates of oxygen reduction in air cathode MFCs.
Continuous Flowing Membraneless Microbial Fuel Cells with Separated Electrode Chambers

Du Fangzhou,Xie Beizhen,Dong Wenbo,Jia Boyang,Dong Kun,Liu Hong

DOI: https://doi.org/10.1016/j.biortech.2011.07.056

IF: 11.4

2011-01-01

Bioresource Technology

Abstract:Microbial fuel cell (MFC) is an emerging technology in the energy and environment field. Its application is limited due to its high cost caused by the utilization of membranes and noble metal catalysts. In this paper, a membraneless MFC, with separated electrode chambers, was designed. The two separated chambers are connected via a channel and the continuous electrolyte flow from anode to cathode drives proton transfer. The proton mass transfer coefficiency in this MFC is 0.9086cm/s, which is higher than reported MFCs with membranes, such as J-cloth and glass fiber. The maximum output voltage is 160.7mV, with 1000Ω resistor. Its peak power density is 24.33mW/m3. SCOD removal efficiency can reach 90.45% via this MFC. If the connection between the two electrode chambers is blocked, the performance of MFC will decrease severely. All the above results prove the feasibility and advantages of this special MFC model.
Air-cathode structure optimization in separator-coupled microbial fuel cells.

Xiaoyuan Zhang,Haotian Sun,Peng Liang,Xia Huang,Xi Chen,Bruce E Logan

DOI: https://doi.org/10.1016/j.bios.2011.09.023

IF: 12.545

2011-01-01

Biosensors and Bioelectronics

Abstract:Microbial fuel cells (MFC) with 30% wet-proofed air cathodes have previously been optimized to have 4 diffusion layers (DLs) in order to limit oxygen transfer into the anode chamber and optimize performance. Newer MFC designs that allow close electrode spacing have a separator that can also reduce oxygen transfer into the anode chamber, and there are many types of carbon wet-proofed materials available. Additional analysis of conditions that optimize performance is therefore needed for separator-coupled MFCs in terms of the number of DLs and the percent of wet proofing used for the cathode. The number of DLs on a 50% wet-proofed carbon cloth cathode significantly affected MFC performance, with the maximum power density decreasing from 1427 to 855 mW/m(2) for 1-4 DLs. A commonly used cathode (30% wet-proofed, 4 DLs) produced a maximum power density (988 mW/m(2)) that was 31% less than that produced by the 50% wet-proofed cathode (1 DL). It was shown that the cathode performance with different materials and numbers of DLs was directly related to conditions that increased oxygen transfer. The coulombic efficiency (CE) was more affected by the current density than the oxygen transfer coefficient for the cathode. MFCs with the 50% wet-proofed cathode (2 DLs) had a CE of >84% (6.8 A/m(2)), which was substantially larger than that previously obtained using carbon cloth air-cathodes lacking separators. These results demonstrate that MFCs constructed with separators should have the minimum number of DLs that prevent water leakage and maximize oxygen transfer to the cathode. (C) 2011 Elsevier B.V. All rights reserved.
Mitigating External and Internal Cathode Fouling Using a Polymer Bonded Separator in Microbial Fuel Cells.

Wulin Yang,Ruggero Rossi,Yushi Tian,Kyoung-Yeol Kim,Bruce E. Logan

DOI: https://doi.org/10.1016/j.biortech.2017.10.109

IF: 11.4

2017-01-01

Bioresource Technology

Abstract:Microbial fuel cell (MFC) cathodes rapidly foul when treating domestic wastewater, substantially reducing power production over time. Here a wipe separator was chemically bonded to an activated carbon air cathode using polyvinylidene fluoride (PVDF) to mitigate cathode fouling and extend cathode performance over time. MFCs with separator-bonded cathodes produced a maximum power density of 190 +/- 30 mW m(-2) after 2 months of operation using domestic wastewater, which was similar to 220% higher than controls (60 +/- 50 mW m(-2)) with separators that were not chemically bonded to the cathode. Less biomass (protein) was measured on the bonded separator surface than the non-bonded separator, indicating chemical bonding reduced external bio-fouling. Salt precipitation that contributed to internal fouling was also reduced using separator-bonded cathodes. Overall, the separator-bonded cathodes showed better performance over time by mitigating both external bio-fouling and internal salt fouling.
Role and Important Properties of a Membrane with Its Recent Advancement in a Microbial Fuel Cell

Aritro Banerjee,Rajnish Kaur Calay,Fasil Ejigu Eregno

DOI: https://doi.org/10.3390/en15020444

IF: 3.2

2022-01-09

Energies

Abstract:Microbial fuel cells (MFC) are an emerging technology for wastewater treatment that utilizes the metabolism of microorganisms to generate electricity from the organic matter present in water directly. The principle of MFC is the same as hydrogen fuel cell and has three main components (i.e., anode, cathode, and proton exchange membrane). The membrane separates the anode and cathode chambers and keeps the anaerobic and aerobic conditions in the two chambers, respectively. This review paper describes the state-of-the-art membrane materials particularly suited for MFC and discusses the recent development to obtain robust, sustainable, and cost-effective membranes. Nafion 117, Flemion, and Hyflon are the typical commercially available membranes used in MFC. Use of non-fluorinated polymeric membrane materials such as sulfonated silicon dioxide (S-SiO2) in sulfonated polystyrene ethylene butylene polystyrene (SSEBS), sulfonated polyether ether ketone (SPEEK) and graphene oxide sulfonated polyether ether ketone (GO/SPEEK) membranes showed promising output and proved to be an alternative material to Nafion 117. There are many challenges to selecting a suitable membrane for a scaled-up MFC system so that the technology become technically and economically viable.

energy & fuels
High-Power Microbial Fuel Cells Based on a Carbon-Carbon Composite Air Cathode.

Xiaoyuan Zhang,Qiuying Wang,Cheng Tang,Hao-Fan Wang,Peng Liang,Xia Huang,Qiang Zhang

DOI: https://doi.org/10.1002/smll.201905240

IF: 13.3

2020-01-01

Small

Abstract:Microbial fuel cells (MFCs) can convert organics in wastewater directly to electricity, and improving oxygen reduction reaction (ORR) performance is critical to their development and future applications. Electrocatalytic ORR performance is determined by the intrinsic activity and accessible amounts of active sites. A surface nitrogen-enriched carbon coaxial nanocable (NCCN) is applied as an ORR electrocatalyst and combined with activated carbon (AC) with 80 wt% addition as a carbon-carbon composite air cathode in MFCs. The fully exposed nitrogen active sites of NCCN contribute to the enhanced ORR activity, while the graphitized core affords a rapid pathway for electron transportation. AC serves as a spacer to construct a porous framework with interconnected ion diffusion channels. This cathode thus exhibits a maximum power density of 2090 mW m(-2), 120% higher than commercial Pt/C electrocatalysts, and also 6% higher than the pure NCCN, indicating a synergistic effect between NCCN and AC. A high-performance NCCN-AC air cathode with a great promise for future MFC applications is reported and an effective strategy to bridge the electrocatalytic performance from nanomaterials to practical devices is presented.
Graphite Fiber Brush Anodes For Increased Power Production In Air-Cathode Microbial Fuel Cells

Bruce Logan,Shaoan Cheng,Valerie Watson,Garett Estadt

DOI: https://doi.org/10.1021/es062644y

IF: 11.4

2007-01-01

Environmental Science & Technology

Abstract:To efficiently generate electricity using bacteria in microbial fuel cells (MFCs), highly conductive noncorrosive materials are needed that have a high specific surface area (surface area per volume) and an open structure to avoid biofouling. Graphite brush anodes, consisting of graphite fibers wound around a conductive, but noncorrosive metal core, were examined for power production in cube (C-MFC) and bottle (B-MFC) air-cathode MFCs. Power production in C-MFCs containing brush electrodes at 9600 m(2)/m(3) reactor volume reached a maximum power density of 2400 mW/m(2) (normalized to the cathode projected surface area), or 73 W/m(3) based on liquid volume, with a maximum Coulombic efficiency (CE) of 60%. This power density, normalized by cathode projected area, is the highest value yet achieved by an air-cathode system. The increased power resulted from a reduction in internal resistance from 31 to 8 Omega. Brush electrodes (4200 m(2)/m(3)) were also tested in B-MFCs, consisting of a laboratory media bottle modified to have a single side arm with a cathode clamped to its end. B-MFCs inoculated with wastewater produced up to 1430 mW/m(2) (2.3 W/m(3), CE = 23%) with brush electrodes, versus 600 mW/m(2) with a plain carbon paper electrode. These findings show that brush anodes that have high surface areas and a porous structure can produce high power densities, and therefore have qualities that make them ideal for scaling up MFC systems.

Engineering A Membrane Based Air Cathode for Microbial Fuel Cells Via Hot Pressing and Using Multi-Catalyst Layer Stacking

Ion Exchange Membrane Cathodes For Scalable Microbial Fuel Cells

Pressurized Air Cathodes for Enhanced Stability and Power Generation by Microbial Fuel Cells

Single-Step Fabrication Using A Phase Inversion Method of Poly(Vinylidene Fluoride) (pvdf) Activated Carbon Air Cathodes for Microbial Fuel Cells

Power Generation by Packed-Bed Air-Cathode Microbial Fuel Cells

Tubular Membrane Cathodes for Scalable Power Generation in Microbial Fuel Cells.

Combined Carbon Mesh and Small Graphite Fiber Brush Anodes to Enhance and Stabilize Power Generation in Microbial Fuel Cells Treating Domestic Wastewater

Defect Free Rolling Phase Inversion Activated Carbon Air Cathodes for Scale-Up Electrochemical Applications

Air-cathode preparation with activated carbon as catalyst, PTFE as binder and nickel foam as current collector for microbial fuel cells.

Microbial Fuel Cell Cathodes with Poly(dimethylsiloxane) Diffusion Layers Constructed Around Stainless Steel Mesh Current Collectors

Immobilization of a Metal-Nitrogen-Carbon Catalyst on Activated Carbon with Enhanced Cathode Performance in Microbial Fuel Cells.

Scalable air cathode microbial fuel cells using glass fiber separators, plastic mesh supporters, and graphite fiber brush anodes.

Microalgae hydrogel-derived monolithicfree-standing air cathode for microbial fuel cells: Tailoring the macroporous structure for enhanced bioelectricity generation

Cathodic Biofouling Control by Microbial Separators in Air-Breathing Microbial Fuel Cells

Power Generation Using an Activated Carbon and Metal Mesh Cathode in A Microbial Fuel Cell

Continuous Flowing Membraneless Microbial Fuel Cells with Separated Electrode Chambers

Air-cathode structure optimization in separator-coupled microbial fuel cells.

Mitigating External and Internal Cathode Fouling Using a Polymer Bonded Separator in Microbial Fuel Cells.

Role and Important Properties of a Membrane with Its Recent Advancement in a Microbial Fuel Cell

High-Power Microbial Fuel Cells Based on a Carbon-Carbon Composite Air Cathode.

Graphite Fiber Brush Anodes For Increased Power Production In Air-Cathode Microbial Fuel Cells