Abstract:The increasing global water pollution leads to the need for urgent development of rapid and accurate water quality monitoring methods. Microbial fuel cells (MFCs) have emerged as real-time biosensors for biochemical oxygen demand (BOD), but they grapple with several challenges, including issues related to reproducibility, operational stability, and cost-effectiveness. These challenges are substantially shaped by the selection of an appropriate air-breathing cathode. Previous studies indicated a critical influence of the cathode on both the enduring electrochemical performance of MFCs and the taxonomic diversity at the electroactive anode. However, the effect of different gas diffusion electrodes (GDE) on 3D-printed single-chamber MFCs for BOD biosensing application and its effect on the bioelectroactive anode was not investigated before. Our study focuses on comparing GDE cathode materials to enhance MFC performance for precise and rapid BOD analysis in wastewater. We examined for over 120 days two Pt-coated air-breathing cathodes with distinct carbonaceous gas diffusion layers (GDLs) and catalyst layers (CLs): cost-effective carbon paper (CP) with hand-coated CL and more expensive woven carbon cloth (CC) with CL pre-applied by the supplier. The results show significant differences in electrochemical characteristics and anodic biofilm composition between MFCs with CP and CC GDE cathodes. CP-MFCs exhibited lower sensitivity (16.6 C L mg−1 m−2) and a narrower dynamic range (25 to 600 mg L−1), attributed to biofouling-related degradation of the GDE. In contrast, CC-MFCs demonstrated superior performance with higher sensitivity (37.6 C L mg−1 m−2) and a broader dynamic range (25 to 800 mg L−1). In conclusion, our study underscores the pivotal role of cathode selection in 3D-printed MFC biosensors, influencing anodic biofilm enrichment time and overall BOD assessment performance. We recommend the use of cost-effective CP GDL with hand-coated CL for short-term MFC biosensor applications, while advocating for CC GDL supplied with CL as the preferred choice for long-term sensing implementations with enduring reliability.

Copper Current Collectors Reduce Long-Term Fouling of Air Cathodes in Microbial Fuel Cells

Copper Anode Corrosion Affects Power Generation in Microbial Fuel Cells

Cathodes for microbial fuel cells that improve the removal of copper ions from wastewater concomitant with power generation using the response surface methodology

Influence of Soluble Microbial Products on the Long-Term Stability of Air Cathodes in Microbial Fuel Cells

Cathodic Biofouling Control by Microbial Separators in Air-Breathing Microbial Fuel Cells

Effect of electrode types on simultaneous anaerobic sulfide and nitrate removal in microbial fuel cell (vol 134, pg 20, 2014)

Mitigating External and Internal Cathode Fouling Using a Polymer Bonded Separator in Microbial Fuel Cells.

Combined Carbon Mesh and Small Graphite Fiber Brush Anodes to Enhance and Stabilize Power Generation in Microbial Fuel Cells Treating Domestic Wastewater

Air-cathode preparation with activated carbon as catalyst, PTFE as binder and nickel foam as current collector for microbial fuel cells.

In Situ Biofilm Removal from Air Cathodes in Microbial Fuel Cells Treating Domestic Wastewater

Impact of Cleaning Procedures on Restoring Cathode Performance for Microbial Fuel Cells Treating Domestic Wastewater.

Removal of copper from aqueous solution by electrodeposition in cathode chamber of microbial fuel cell

Mesh optimization for microbial fuel cell cathodes constructed around stainless steel mesh current collectors

Engineering A Membrane Based Air Cathode for Microbial Fuel Cells Via Hot Pressing and Using Multi-Catalyst Layer Stacking

Microbial Fuel Cell Cathodes with Poly(dimethylsiloxane) Diffusion Layers Constructed Around Stainless Steel Mesh Current Collectors

Improved Performance of Microbial Fuel Cells Enriched with Natural Microbial Inocula and Treated by Electrical Current

Long-term performance of activated carbon air cathodes with different diffusion layer porosities in microbial fuel cells

Effects of Anode Materials on Electricity Generation and Organic Wastewater Treatment of 6 L Microbial Fuel Cells

Ag@Co/Zn N‐Doped Carbon as Antibacterial Oxygen Reduction Catalysts for Microbial Fuel Cells

Impact of Air-Cathodes on Operational Stability of Single-Chamber Microbial Fuel Cell Biosensors for Wastewater Monitoring

Recent Progress in Electrodes for Microbial Fuel Cells