Abstract:Advances in Mechanical Engineering, Volume 14, Issue 5, May 2022. Experimental investigations of the condensation and evaporation of R410A on the outside of two double-side enhanced heat transfer tubes were conducted, and the tube performance was compared with that of a smooth copper tube. The research object consisted of a smooth tube with a length of 2000 mm and an outer diameter of 25.4 mm and two double-side enhanced tubes of the same size. The evaporation experiments were run under the following conditions: the evaporation saturation temperature was 7°C, water inlet temperature was 8°C–18°C, and water flow rate was 0.6–1.6 m3/h. The condensation experiments were run under the following conditions: the saturation temperature was 35°C, water inlet temperature was 21°C–30°C, and water flow rate was 0.4–1.6 m3/h. During the data processing, the heat transfer coefficient of the water side was obtained using the Gnielinski-Wilson method, and that of the refrigerant side was obtained using the thermal resistance separation method. The effect of the surface structure on the heat transfer performance was analyzed, and a strengthening measure was proposed. The experimental results indicate that the evaporation heat transfer coefficients outside the smooth tube increased with the raise of the inlet water temperature, while the double-side enhanced tubes decreased; both the condensation heat transfer coefficients outside the smooth tube and the enhanced tubes increased with the increase of the water flow rate. Due to the different type of enhanced tube ribs, tube #3 surface structure is more conducive to the formation of vaporization core, which is about 30% higher than the outer heat transfer coefficient of tube #2. It is more in line with the requirements of strengthening horizontal single tube external pool boiling heat transfer. In the condensation experiment, the condensation heat transfer coefficients outside the smooth tube increased with the raise of the inlet water temperature, while the double enhanced tubes decreased; both the condensation heat transfer coefficients outside the smooth tube and the enhanced tubes increased with the increase of the water flow rate. With the analysis of the rib structure, the outer surface structure of tube #2 has stronger drainage capacity, and the external average condensation heat transfer coefficient is about 7% higher than that of tube #3, which is more in line with the requirements of condensing heat transfer outside the single tube.

Pool boiling heat transfer outside horizontal tubes at higher heat flux

Pool Boiling Heat Transfer of R134a Outside Reentrant Cavity Tubes at Higher Heat Flux

Experimental study on the pool boiling heat transfer of R134a outside various enhanced tubes

Falling Film Evaporation and Nucleate Pool Boiling Heat Transfer of R134a on the Same Enhanced Tube

Nucleate pool boiling and filmwise condensation heat transfer of R134a on the same horizontal tubes

Experimental Study of Condensation Heat Transfer of R134a Inside the Micro-Fin Tubes at High Mass Flux

Boiling Heat Transfer of R134a Outside Horizontal Doubly-Enhanced Tubes

Experimental comparison on condensation and evaporation outside double-side enhanced horizontal tubes

Boiling Heat Transfer of R22 Outside Single Horizontal Doubly-Enhanced Tubes

Effect of Subsurface Tunnel on the Nucleate Pool Boiling Heat Transfer of R1234ze(E), R1233zd(E) and R134a

Heat transfer enhancement of helical tubes during pool boiling

Experimental determination of the role of roughness and wettability on pool-boiling heat transfer of refrigerant

Flow Boiling Heat Transfer Characteristic of Refrigerant R1234ze(E) in Horizontal Circular Tube

Flow Boiling Heat Transfer of R134a in a Vertical Helically Coiled Tube

Flow Boiling Heat Transfer Characteristics in Horizontal, Three-Dimensional Enhanced Tubes

Comparison of the Evaporation and Condensation Heat Transfer Coefficients on the External Surface of Tubes in the Annulus of a Tube-in-Tube Heat Exchanger

Numerical Investigation on the Nucleate Pool Boiling Heat Transfer of R134a Outside the Plain Tube

Comparison of flow boiling heat transfer characteristics inside different enhanced heat transfer tubes

R410A flow boiling coefficient in horizontal annular channels of enhanced tubes, Part II: Heat transfer

Experimental Study on Condensation Heat Transfer of Horizontal Enhanced Tubes for R134a

Heat Transfer of R134a in a Horizontal Internally Ribbed Tube and in a Smooth Tube under Super Critical Pressure