Abstract:Tackling the challenges through comprehensive materials performance manipulation, delicate barrier material design, and transient liquid phase bonding technique. It is demonstrated that an all‐Mg3Sb2‐based module with a high efficiency of ≈8.3% is superior to the conventional reported PbTe‐, Skutterudite‐, and half‐Heusler‐based modules. This work will catalyze the application process of Mg3(Sb, Bi)2‐based materials in harvesting the mid‐temperature heat. n‐Type Mg3(Sb, Bi)2 shows great prospects in mid‐temperature power generation due to its extraordinary thermoelectric (TE) performance, low‐cost, and environment‐friendly attributes. However, its practical application is hindered by the slow progress of its p‐type counterpart. Herein, a high ZT of ≈0.9 at 773 K is achieved for p‐type Na0.01Mg1.7Zn1Yb0.25Sb2 through manipulation of the electronic transport properties. Then thermal expansion matched barrier material Fe75Sb25 is subtly obtained for Na0.01Mg1.7Zn1Yb0.25Sb2. The contact resistivity no longer increases significantly after aging for 72 hours at 673 K and tends to stabilize, remaining below ≈17 μΩ cm2 after 168 hours. Paired with the high‐performance n‐type Mg3(Sb, Bi)2, the transient liquid phase bonding technique is adopted to connect the hot side of the all‐Mg3Sb2‐based legs to electrode at low temperature, which enables service at high temperature. This all‐Mg3Sb2‐based module displays a high efficiency of ≈8.3% at a temperature difference of ≈430 K and shows good thermal stability when the hot side temperature is maintained at 673 K. This work merits the great potential of the all‐Mg3Sb2‐based device for heat recovery.

Half‐Heusler Thermoelectric Module with High Conversion Efficiency and High Power Density

Engineering the Thermoelectric Transport in Half‐Heusler Materials through a Bottom‐Up Nanostructure Synthesis

Realizing high figure of merit in heavy-band p -type half-Heusler thermoelectric materials

High Thermoelectric Performance of a Sc2Si2Te6 Monolayer at Medium Temperatures: an Ab Initio Study.

Half Heusler Alloys for Efficient Thermoelectric Power Conversion

High Efficiency Half‐Heusler Thermoelectric Materials for Energy Harvesting

Power generation from n-type NbCo1−xNixSn and p-type NbFe1−xMnxSb ternary half-Heusler compounds: from materials development to module fabrication

High Band Degeneracy Contributes to High Thermoelectric Performance in p-Type Half-Heusler Compounds

Half-Heusler alloys as emerging high power density thermoelectric cooling materials

High‐Efficiency Thermoelectric Module Based on High‐Performance Bi0.42Sb1.58Te3 Materials

A Device-to-Material Strategy Guiding the “Double-High” Thermoelectric Module

Enhanced Thermoelectric Performance in Hf-Free p-Type (Ti, Zr)CoSb Half-Heusler Alloys

Half-Heusler Compounds: Promising Materials For Mid-To-High Temperature Thermoelectric Conversion

Bismuth Telluride/Half‐Heusler Segmented Thermoelectric Unicouple Modules Provide 12% Conversion Efficiency

Performance Advancements in P-Type TaFeSb-Based Thermoelectric Materials through Composition and Composite Optimizations

Bi2Te3-Based Thermoelectric Modules for Efficient and Reliable Low-Grade Heat Recovery

All‐Mg3Sb2‐Based Module for Thermoelectric Power Generation

High-performance Sb2Si2Te6 thermoelectric device

Realizing ultrahigh ZT value and efficiency of the Bi2Te3 thermoelectric module by periodic heating

High‐Performance Thermoelectric Material and Module Driven by Medium‐Entropy Engineering in SnTe

High‐Performance Industrial‐Grade p‐Type (Bi,Sb)2Te3 Thermoelectric Enabled by a Stepwise Optimization Strategy