Abstract:Antimony chalcogenides are widely studied as a light-absorbing material due to their merits of low toxicity, efficient cost, and excellent photovoltaic properties. However, the band gaps of antimony selenide (approximately 1.1 eV) and antimony sulfide (approximately 1.7 eV) both deviate from the optimal detailed balance band gap (∼1.3 eV) for terrestrial single-junction solar cells. Notably, the band gap of Sb2(S, Se)3 can be tunable in the range from 1.1 to 1.7 eV, which can cover the detailed balance band gap. In this work, the vapor transport deposition method with two independent evaporation sources is used to deposit Sb2(S, Se)3 thin films. By carefully optimizing the evaporation temperature and the start evaporation time of the Sb2Se3 and Sb2S3 sources, a suitable band gap of 1.33 eV is obtained. Finally, on the basis of the optimal Sb2(S, Se)3 films, Sb2(S, Se)3 solar cells without a hole transport layer achieved an efficiency of 7.03%.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c10758.Saturated vapor pressure curves of Sb2Se3 and Sb2S3; temperature–time curves of Sb2Se3 and Sb2S3 sources; top-view SEM images at different Sb2Se3 and Sb2S3 source temperatures; XRD diffraction pattern under different Sb2Se3 and Sb2S3 source temperatures; transmission spectroscopy at different Sb2Se3 and Sb2S3 source temperatures; schematic diagram of thin-film light absorption; heating process of the uniform Sb2(S, Se)3 films and band gaps of Sb2(S, Se)3 films; 1/C2–V curves of the devices; band gaps of the devices obtained from EQE data; J–V curves under different light intensities; atomic and ionic radii; material parameters for SCAPS simulations; CdS trap state parameters for SCAPS simulations; and Sb2(S, Se)3 trap state parameters (PDF)This article has not yet been cited by other publications.

Sb-2(Se1-xSx)(3) Thin-Film Solar Cells Fabricated by Single-Source Vapor Transport Deposition

Fabrication of Homogenous Sb 2 (S,Se) 3 Solar Cells by Close Space Sublimation Using a Single Alloyed Powder Source

Solvent‐Assisted Hydrothermal Deposition Approach for Highly‐Efficient Sb2(S,Se)3 Thin‐Film Solar Cells

Fabricating over 7%-efficient Sb2(S,Se)3 thin-film solar cells by vapor transport deposition using Sb2Se3 and Sb2S3 mixed powders as the evaporation source

Vapor Transport Deposition of Sb 2 (S,Se) 3 Solar Cells with Continuously Tunable Band Gaps

Stable SnS x Se 1−x /CdS thin-film solar cells via single-source vapor transport deposition: unveiling band alignment at heterojunction interface

An effective combination reaction involved with sputtered and selenized Sb precursors for efficient Sb2Se3 thin film solar cells

Selenium‐Rich Sb2(S,Se)3 Thin Films Deposited via Sequential Chemical Bath Deposition for High‐Efficiency Solar Cells

Magnetron Sputtered Sb2Se3-based Thin Films Towards High Performance Quasi-Homojunction Thin Film Solar Cells

Sb2Se3 thin film solar cells in substrate configuration and the back contact selenization

Optimisation of Sb2S3 thin-film solar cells via Sb2Se3 post-treatment

Regulating Deposition Kinetics via A Novel Additive-assisted Chemical Bath Deposition Technology Enables 10.57%-efficient Sb2Se3 Solar Cells

Oxygen Content Modulation Toward Highly Efficient Sb2Se3 Solar Cells

Quasi-Vertically Oriented Sb 2 Se 3 Thin-Film Solar Cells with Open-Circuit Voltage Exceeding 500 mV Prepared via Close-Space Sublimation and Selenization

Co‐Evaporated CuSbSe2 Thin Films for Solar Cells

Fabricating High‐Efficiency Sb2(S,Se)3 Solar Cells by Novel Additive‐Assisted Longitudinal Component Engineering

Temperature‐Gradient Solution Deposition Amends Unfavorable Band Structure of Sb2(S,Se)3 Film for Highly Efficient Solar Cells

Se-Elemental Concentration Gradient Regulation for Efficient Sb2(S,Se)3 Solar Cells With High Open-Circuit Voltages

HTL-Free Sb 2 (S, Se) 3 Solar Cells with an Optimal Detailed Balance Band Gap

Molecular Beam Epitaxy Deposition of In Situ O‐Doped CdS Films for Highly Efficient Sb2(S,Se)3 Solar Cells

Self‐Regulated Growth of Large‐Grain Sb2S3 Thin Films for High‐Efficiency Solar Cells