Abstract:Objective, Total talar replacement (TTR) using a customised talus prosthesis is an emerging surgical alternative to conventional total ankle arthroplasty (TAA) for treating ankle problems. Upon satisfying clinical reports in the literature, this study explored the advantages of TTR in restoring foot biomechanics during walking compared with TAA through computational simulations.Methods, A dynamic finite element foot model was built from the MRIs of a healthy participant and modified into two implanted counterparts (TTR and TAA) by incorporating the corresponding prosthetic components into the ankle joint. Twenty bony parts, thirty-nine ligament/tendon units, nine muscle contractors, and bulk soft tissue were included in the intact foot model. The TTR prosthesis was reconstructed from the mirror image data of the participant's contralateral talus and the TAA prosthesis was modelled by reproducing the Scandinavian ankle replacement procedure in the model assembly. The model was meshed with explicit deformable elements and validated against existing experimental studies that have assessed specific walking scenarios. Simulations were performed using the boundary conditions (time-variant matrix of muscle forces, segment orientation, and ground reaction forces) derived from motion capture analyses and musculoskeletal modelling of the participant's walking gait. Outcome variables, including foot kinematics, joint loading, and plantar pressure were reported and compared among the three model conditions.ResultsLinear regression indicated a better agreement between the TTR model and intact foot model in plots of joint motions and foot segment movements during walking (R2 = 0.721–0.993) than between the TAA and intact foot (R2 = 0.623–0.990). TAA reduced talocrural excursion by 21.36%–31.92% and increased (MTP) dorsiflexion by 3.03%. Compared with the intact foot, TTR and TAA increased the midtarsal joint contact force by 17.92% and 10.73% respectively. The proximal-to-distal force transmission within the midfoot was shifted to the lateral column in TTR (94.52% or 210.54 N higher) while concentrated on the medial column in TAA (41.58% or 27.55 N higher). The TTR produced a plantar pressure map similar to that of the intact foot. TAA caused the plantar pressure centre to drift medially and increased the peak forefoot pressure by 7.36% in the late stance.ConclusionThe TTR better reproduced the foot joint motions, segment movements, and plantar pressure map of an intact foot during walking. TAA reduced ankle mobility while increasing movement of the adjacent joints and forefoot plantar pressure. Both implant methods changed force transmission within the midfoot during gait progression.The translational potential of this article Our work is one of the few to report foot segment movements and the internal loading status of implanted ankles during a dynamic locomotion task. These outcomes partially support the conjecture that TTR is a prospective surgical alternative for pathological ankles from a biomechanical perspective. This study paves the way for further clinical investigations and systematic statistics to confirm the effects of TTR on functional joint recovery.

Total Ankle Total Talus Replacement Using a 3D Printed Talus Component: A Case Report.

3d Printed Total Talus Replacement For Avascular Necrosis Of The Talus

Partial talar replacement with a novel 3D printed prosthesis

Initial Safety of Total Talus Replacement Used to Treat Talar Avascular Necrosis

Total Talar Replacement with Custom-Made Vitallium Prosthesis for Talar Avascular Necrosis

Outcomes of cobalt-chrome 3D-printed total talus replacement with and without combined total ankle replacement

Outcomes following total ankle total talus replacement: A systematic review

Three dimension printing talar prostheses for total replacement in talar necrosis and collapse

Custom Patient-Specific 3D-Printed Titanium Truss Tibiotalocalcaneal Arthrodesis Implants for Failed Total Ankle Replacements: Classification, Technical Tips, and Treatment Algorithm

Total Talar Replacement Using a Novel 3D-Printed Prosthesis for Recurrent Giant Cell Tumour of the Talus

Avascular Necrosis of the Talus: Diagnosis, Treatment, and Modern Reconstructive Options

Total Ankle/Total Talus Replacement – Retrospective Comparison of Surgeon Decision Relative to Three-Dimensional Joint Health Assessment

Total Talar Replacement with a Novel 3D Printed Modular Prosthesis for Tumors

Single-Center, Early Experience with the First 3D-Printed Surface, Fixed Bearing, Total Ankle Arthroplasty: A Minimum of 2-Year Follow-Up

Development of an internally braced prosthesis for total talus replacement

Designing and additive manufacturing of talus implant for post-traumatic talus avascular necrosis: a case study

Total Talus Allograft Transplantation With Subtalar Arthrodesis for Missing Talus: A Report of a Rare Case

Early Experience with a 3-D Printed Porous Surface, Fixed-Bearing, Total Ankle Arthroplasty: A Minimum of 2-Year Follow-Up

Dynamic finite element analyses to compare the influences of customised total talar replacement and total ankle arthroplasty on foot biomechanics during gait

3D-Printed Porous Titanium Augments for Reconstruction of Massive Bone Defect in Complex Revision Total Knee Arthroplasty: Implant Design and Surgical Technique

Reconstruction of the Talus and Calcaneus Using a Three-Dimensional (3D)-Printed Custom Implant Following a Shotgun Wound: A Case Report