Abstract:Introduction/Purpose: As the fourth generation of total ankle arthroplasty (TAA) implants evolve, treatment solutions for end- stage ankle arthritis continue to improve. Technological advancements in CT guided planning and 3-D printing offers surgeons the ability to perform TAA with patient specific instrumentation and implants. 3-D printed components are designed to act as scaffold in hopes to facilitate early in-growth, to increase implant stability, to support long-term survivorship, and ultimately to improve the quality of life our patients. We present our early experience at a single academic center with a minimum of 2-year follow up data on the first 3-D printed, fixed bearing, TAA in the United States. We hypothesize that 3-D printed technology will demonstrate improved long-term survival and increased bony in-growth on the implant-bone interface. Methods: A retrospective review was performed on patients who underwent TAA with a minimum of 2-year clinical and radiographic data in which this 3-D printed TAA was utilized at our single academic center. Patient demographic, radiographic, and functional outcome scores were collected preoperatively, at 6 months, 1 year, and 2 years. The severity of ankle arthritis and associated deformities in patients were stratified using the COFAS classification. The primary outcomes of this study were implant survivorship, comparative analysis of preoperative and postoperative Patient Reported Outcomes Measurement Information System (PROMIS) physical function scores, VAS pain scores, radiographic development of linear radiolucency >2 mm, cystic radiolucency > 5mm, subsidence, and adverse events within 2 years of surgery. Results: Thirty patients were included with a median follow-up of 26 months (range, 24-36 months). Implant survival rate was 90%. One patient was revised to a stemmed TAA secondary to tibial subsidence. One patient required a TTC fusion secondary to Charcot collapse. One patient was revised to a staged ankle fusion secondary to periprosthetic joint infection. Two patients (6.7%) experienced linear radiolucency >2mm with tibial subsidence in which one patient required a revision TAA (mentioned above) and another who was asymptomatic. No significant cystic radiolucency >5 mm were identified. Five patients required re-operation from complications unrelated to the implant. VAS scores decreased significantly from 6 (IQR, 4-8) to 1 (IQR, 2-4) (P <.001; r=0.55). PROMIS Physical scores increased significantly from 43.6 (IQR, 33-47.7) to 50.8 (44.8-57.7)(P <.001; r=0.60). Conclusion: The utilization of this new 3-D printed, fixed bearing TAA demonstrated a ninety percent overall implant survival rate in our small cohort of patients. Further data will be required to determine the long term efficacy of this new 3-D printed implant on patient outcomes. Our early experience and complications presented in our study demonstrate that this 3-D printed TAA implant is safe and effective in the treatment of end-stage ankle arthritis.

Early Experience with a 3-D Printed Porous Surface, Fixed-Bearing, Total Ankle Arthroplasty: A Minimum of 2-Year Follow-Up

Single-Center, Early Experience with the First 3D-Printed Surface, Fixed Bearing, Total Ankle Arthroplasty: A Minimum of 2-Year Follow-Up

Early Radiographic and Clinical Outcomes of a Novel, Fixed-Bearing Fourth-Generation Total Ankle Replacement System

Two-Year Outcomes After Total Ankle Replacement with a Novel Fixed-Bearing Implant by a Single Surgeon Non-Inventor

Outcomes of cobalt-chrome 3D-printed total talus replacement with and without combined total ankle replacement

Initial Safety of Total Talus Replacement Used to Treat Talar Avascular Necrosis

Outcomes After Total Ankle Arthroplasty in Patients Aged ≤50 Years at Midterm Follow-up

Clinical Outcomes of the Lateral Trabecular Metal Total Ankle Replacement at a 5-Year Minimum Follow-up

Increased Early Revision Rate With the INFINITY Total Ankle Prosthesis

A new ligament-compatible patient-specific 3D-printed implant and instrumentation for total ankle arthroplasty: from biomechanical studies to clinical cases

Custom Patient-Specific 3D-Printed Titanium Truss Tibiotalocalcaneal Arthrodesis Implants for Failed Total Ankle Replacements: Classification, Technical Tips, and Treatment Algorithm

3d Printed Total Talus Replacement For Avascular Necrosis Of The Talus

Contemporary modern total ankle arthroplasty (TAA): A systematic review and meta-analysis of indications, survivorship and complication rates

3D Printing Hip Prostheses Offer Accurate Reconstruction, Stable Fixation, and Functional Recovery for Revision Total Hip Arthroplasty with Complex Acetabular Bone Defect

Prospective Multicenter Study of Salto Talaris Ankle Arthroplasty With Minimum 4-Year Follow-Up

Positive and Negative Factors for the Treatment Outcomes Following Total Ankle Arthroplasty? A Systematic Review

Total Ankle Total Talus Replacement Using a 3D Printed Talus Component: A Case Report.

Outcomes following total ankle total talus replacement: A systematic review

Implant Choice May Reduce the Risk of Early Mechanical Failure in Total Ankle Replacement

Use of Patient-Specific 3D-Printed Titanium Implants for Complex Foot and Ankle Limb Salvage, Deformity Correction, and Arthrodesis Procedures

Survival and risk assessment in revision arthroplasty of the ankle