Abstract:Objective To explore the feasibility and clinical efficacy of long-segmental bone defects after en bloc tumor resection of lower limb segment with composite of titanium alloy 3D printed prosthesis and vascularized fibular autograft and bioceramics.Methods 5 patients with lower extremity tumor (1 high grade chondrosarcoma,1 Ewing sarcoma,1 single metastatic tumor and 2 osteosarcoma) were treated by en bloc resection and precise reconstruction with segmental 3D-printed,custom-made prosthesis from August 2015 to November 2016,which composed of 1 male and 4 females,ranged from 16 to 56 years old,the average was 32± 19.3 years old.Three-dimensional computed tomography reconstructed images of patients' tumors were built before surgery.Custom-made prostheses were manufactured based on the patients' reconstructed images with micro-pores on the surface.After en bloc tumor resection with the help of osteotomy guide plate,the defects were reconstructed with 3D-printed,custom-made prostheses.Vascularized fibular autografts were put inside the prostheses,and the interval space among them was filled with bioceramics.Results All the 5 cases were performed surgical planning before the surgery with prosthesis and guide plate were designed at the same time.After verification of the finite element analysis SLM (2 cases) and the EBM (3 cases) were used to process prosthesis,and were designed into porous sharp with 210.98±66.16 mm in length and 26 901.76±12 903.96 mm3 in volume.Then the prosthesis would be cleaned and sterilized.All 5 operation were proceeded according to the plan of preoperative.The intra-operative guide plate were installed on the bone surface stably.The bone cutting was guided according to the plan of preoperative.By intra-operative frozen pathological examination,there were no malignant tissues in near and far marrow cavity.Unfolded fibular flap with 168.75±49.07 mm in length and porous tricalcium phosphate particle composite implants with 10±4.08 g were used in 4 cases and bone cement was used in 1 cases of metastatic tumor.The average operation time was 261±85 min and average blood loss was 540±182 ml.After a mean follow-up time of 6.4 months (1-15 months),all 5 cases survived with no local recurrence and pulmonary metastasis tumor.2 cases with vascular pedicle fibular transplant confirmed the survival of fibula via bone scan 3 months after operation.All cases were no infection,fractures,prosthesis loosening,except broken screw in 1 case.The Musculoskeletal Tumor Society (MSTS) 93 score was 17-26.Conclusion Long segment tubular titanium alloy 3D printed prosthesis with vascularized fibular autograft and bioceramics could reconstruct the segmental defects caused by tumor resection.

3D‐Printed Talus‐Calcaneus Prosthesis in Treating Ewing's Sarcoma: A Case Report

Total Talar Replacement with a Novel 3D Printed Modular Prosthesis for Tumors

Total Talar Replacement Using a Novel 3D-Printed Prosthesis for Recurrent Giant Cell Tumour of the Talus

Reconstruction with a 3D-Printed Megaprosthesis with Ankle Arthrodesis after Distal Tibial Tumor Resection

Case Report: Reconstruction of Medialis Malleolus (1/4 of the Ankle Joint) after Resection of Distal Tibia Tumor with an Uncemented Three-Dimensional-Printed Prosthesis

Three-dimensional printed custom-made modular talus prosthesis in patients with talus malignant tumor resection

Reconstruction of the Talus and Calcaneus Using a Three-Dimensional (3D)-Printed Custom Implant Following a Shotgun Wound: A Case Report

Arthrodesis reconstruction of distal tibia by 3D-printed porous prosthesis after malignant tumor resection

Case report: Individualized 3D-printed uncemented distal fibular prosthesis preserving the lateral malleolus for repair of distal fibular defects

Uncemented Three-Dimensional-printed Prosthetic Reconstruction for Massive Bone Defects of the Proximal Tibia

Intercalary Reconstruction of the “Ultra-Critical Sized Bone Defect” by 3D-Printed Porous Prosthesis after Resection of Tibial Malignant Tumor

Three dimension printing talar prostheses for total replacement in talar necrosis and collapse

Partial talar replacement with a novel 3D printed prosthesis

Reconstruction with Customized, 3D-Printed Prosthesis after Resection of Periacetabular Ewing’s Sarcoma in Children Using "triradiate Cartilage-Based" Surgical Strategy:A Technical Note

Aplication of 3D-Printed Prosthesis on Construction of Long Segmental Bone Defect after Tumor Resection

Cmar_a_245949 2503..2512

Reconstruction with Double Pedicel Fibular Graft and Ankle Arthrodesis for Aggressive Chondroblastoma in the Distal Tibia

3D-Printed Modular Endoprosthesis Reconstruction Following Total Calcanectomy in Calcaneal Malignancy

Total Talar Replacement with Custom-Made Vitallium Prosthesis for Talar Avascular Necrosis

Three-dimensional-printed intercalary prosthesis for the reconstruction of large bone defect after joint-preserving tumor resection.

Case Report: Three-dimensional Printed Prosthesis Reconstruction for Patello-Femoral Large Osteochondral Defects in a Patient with Distal Femoral Giant Cell Tumour: A Case Report