Abstract:Objective: To explore the design points of a three-dimensional (3D) printed customized cementless intercalary endoprosthesis with an intra-neck curved stem and to evaluate the key points and mid-term effectiveness of its application in the reconstruction of ultrashort bone segments in the proximal femur. Methods: Between October 2015 and January 2021, 17 patients underwent reconstruction with a 3D printed-customized cementless intercalary endoprosthesis with an intra-neck curved stem. There were 11 males and 6 females, the age ranged from 10 to 76 years, with an average of 30.1 years. There were 9 cases of osteosarcoma, 4 cases of Ewing sarcoma, 2 cases of chondrosarcoma, 1 case of liposarcoma, and 1 case of myofibroblastoma. The disease duration was 5-14 months, with an average of 9.5 months. Enneking staging included 16 cases of stage ⅡB and 1 case of stage ⅢB. The distances from the center of the femoral head to the body midline and the acetabular apex were measured preoperatively on X-ray images. Additionally, the distances from the tip of the intra-neck curved stem to the body midline and the acetabular apex were measured at immediate postoperatively and last follow-up. The neck-shaft angle was also measured preoperatively, at immediate postoperatively, and at last follow-up. The status of osseointegration at the bone-prosthesis interface and bone growth into the prosthesis surface were assessed by X-ray films, CT, and Tomosynthesis-Shimadzu metal artefact reduction technology (T-SMART). The survival status of the patients, presence of local recurrence or distant metastasis, and occurrence of postoperative complications were assessed. The recovery of lower limb function was evaluated pre- and post-operatively using the Musculoskeletal Tumor Society (MSTS) scoring system, and pain relief was evaluated using the visual analogue scale (VAS) scores. Results: The patient's femoral resection length was (163.1±57.5) mm, the remaining proximal femoral length was (69.6±9.3) mm, and the percentage of femoral resection length/total femoral length was 38.7%±14.6%. All 17 patients were followed up 25-86 months with an average of 58.1 months. During the follow-up, 1 patient died of lung metastasis at 46 months postoperatively, and the remaining 16 patients survived tumor-free. There was no complication such as periprosthetic infection, delayed incision healing, aseptic loosening, prosthesis fracture, or periprosthetic fracture. No evidence of micromotion or wear around the implanted stem of the prosthesis was detected in X-ray and T-SMART evaluations. There was no significant radiolucent lines, and radiographic evidence of bone ingrowth into the bone-prosthesis interface was observed in all stems. There was no significant difference in the distance from the tip of the curved stem to the body midline and the apex of the acetabulum at immediate postoperatively and last follow-up compared with the distance from the center of the femoral head to the body midline and the apex of the acetabulum before operation, respectively (P>0.05), and there was no significant difference in the above indexes between immediate postoperatively and last follow-up (P>0.05). The differences in the neck-shaft angle at various time points before and after operation were also not significant (P>0.05). At last follow-up, the MSTS score was 26.1±1.2 and the VAS score was 0.1±0.5, which were significantly improved when compared with those before operation [19.4±2.1 and 5.7±1.0, respectively] (t=14.735, P<0.001; t=21.301, P<0.001). At last follow-up, none of the patients walked with the aid of crutches or other walkers. Conclusion: The 3D printed customized cementless intercalary endoprosthesis with an intra-neck curved stem is an effective method for reconstructing ultrashort bone segments in the proximal femur following malignant tumor resection. The operation is reliable, the postoperative lower limb function is satisfactory, and the incidence of complications is low.

Efficacy of 3D-printed segmental tumor prosthesis for reconstruction of bone defects after resection of weight-bearing long bone tumors in the lower extremity

[Endoprosthetic Reconstruction after Wide Resection of Primary Bone Tumor Around the Knee].

[Mid-term effectiveness of hip preservation in the reconstruction of ultrashort bone segments in the proximal femur with three-dimensional printed customized cementless intercalary endoprosthesis with an intra-neck curved stem]

Application of three-dimensional printed endoprosthesis for reconstruction after metaphysis-involved intercalary tumor resection

Reconstruction for long segment bone defect of long bone malignant tumor in teenagers

Three-dimensional-printed titanium prostheses with bone trabeculae enable mechanical-biological reconstruction after resection of bone tumours

Arthrodesis reconstruction of distal tibia by 3D-printed porous prosthesis after malignant tumor resection

Reconstruction with a 3D-Printed Megaprosthesis with Ankle Arthrodesis after Distal Tibial Tumor Resection

Clinical effects of 3D printed porous titanium-alloy prosthesis in reconstruction of long bone defects of lower extremities

The application of custom 3D-printed prostheses with ultra-short stems in the reconstruction of bone defects: a single center analysis

Clinical study of 3D printed personalized prosthesis in the treatment of bone defect after pelvic tumor resection

Reconstruction of the proximal radius with 3D-printed personalized prosthesis after tumor resection: case series

Clinical exploration of the international society of limb salvage classification of endoprosthetic failure using Henderson in the application of 3D-printed pelvic tumor prostheses

Reconstruction with 3D-Printed Pelvic Endoprostheses after Resection of a Pelvic Tumour.

Three-dimensional printed customized uncemented unipolar prosthesis combined with ligament reconstruction for tumorous defect of the distal femur in children

Using 3D printing endoprosthesis for reconstruction after resection of bone tumor

Elbow Hemiarthroplasty with a 3D-Printed Megaprosthesis for Defects of the Distal Humerus or Proximal Ulna after Tumour Resection

3D-printed personalised prostheses for bone defect repair and reconstruction following resection of metacarpal giant cell tumours

Applying 3D‐Printed Porous Ti6Al4V Prostheses to Repair Osteomyelitis‐Induced Partial Bone Defects of Lower Limbs: Finite Element Analysis and Clinical Outcomes

[Non-Cemented Modular Prosthetic Reconstruction for Bone Defect after Tumor Resection in Lower Extremities].

Applying 3D-printed prostheses to reconstruct critical-sized bone defects of tibial diaphysis (> 10 cm) caused by osteomyelitis and aseptic non-union